PETG-CF
Carbon-Fiber-Reinforced PETG
24 products from 21 makers. Bambu Lab sells its own filament of this material for the H2C.
- Tensile modulus (XY)
- 3.7GPa
- 11 products · middle half 2.93–4.08
- Tensile strength (XY)
- 49.4MPa
- 12 products · middle half 43–53.7
- Tensile strength (Z)
- 28.5MPa
- 4 products · middle half 27–32
- Notched Charpy impact
- 8kJ/m²
- 5 products · middle half 4–15.7
- HDT at 0.45 MPa
- 72°C
- 11 products · middle half 71–75
- Price
- 41CAD/kg
- 3 products · 35–56
PETG-CF is a carbon-fibre-filled PETG copolyester. Makers sell it for end-use parts that do not need the full strength of carbon, and for structural parts and fixtures. Its HDT at 0.45 MPa is 72 °C, near its glass transition, and a maker notes the added stiffness costs impact resistance. On the H2C every product needs a hardened nozzle, and most print at 240–260 °C without chamber heat.
Partly documented Price rests on 3 products and tensile strength (Z) on 4 products. Each figure is the median of the products that publish it comparably, and beside it the middle half of them; a value on a test bar no document describes as printed, or with no stated test load, is set apart, except a heat deflection of a plastic that cannot crystallise, which its glass transition sets, unless its document points to a moulded or resin bar.
On the H2C
Printing in full- Nozzle
- 240–260 °C
- most products that give one
- Bed
- 70 °C
- most products that give one
- Heated chamber
- none needed
- 19 of 24 products
- Drying
- 40–80 °C, 2–12 h
- 15 of 24 products call for it; 9 more give it as optional
- Nozzle type
- hardened
- 14 of 24 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 10 more
No product's setting is beyond the H2C's limits: nozzle 350 °C, bed 120 °C, heated chamber 65 °C.
Among the materials
Carbon fibre adds little to PETG's heat resistance: PETG-CF's HDT at 0.45 MPa is 72 °C against 70 °C. Against PETG-GF, PETG-CF is 58 % stiffer, 10 % stronger flat and 7 % stronger across the layers. Among the materials, PETG-CF has a high tensile modulus (XY) and a low HDT at 0.45 MPa and price: each is in the top or bottom quarter of the materials that publish it. The rest of its key properties sit in the middle half.
Against its alternatives, PETG-CF has the highest tensile strength
How does it compare with what an engineer would buy instead?
- PETG-CF: its products' median and middle half
- an alternative
- lowest to highest
- each material's median (top row)
Each row is a material, each column a property: the bar is the middle half of a material's products, the tick their median, the hairline their lowest to highest; the ticks above the rows are every material's median.
The figure as a table
| Material | Modulus (XY) (GPa) | Strength (XY) (MPa) | Strength (Z) (MPa) | Notched Charpy (kJ/m²) | HDT 0.45 MPa (°C) | Price (CAD/kg) |
|---|---|---|---|---|---|---|
| PETG-CF (this material) | 3.7 (2.93–4.08) · 11 | 49.4 (43–53.7) · 12 | 28.5 (27–32) · 4 | 8 (4–15.7) · 5 | 72 (71–75) · 11 | 41 · 3 |
| PETG | 1.69 (1.42–1.95) · 24 | 47 (40.3–50.6) · 34 | 30.2 (28–36.5) · 16 | 6 (4.76–8) · 10 | 70 (69–71) · 32 | 26 (25–32) · 11 |
| PETG-GF | 2.33 · 3 | 45 · 3 | 26.6 · 2 | — | 76 · 1 | 37 · 1 |
| PLA-CF | 2.8 (2.26–3.65) · 7 | 42.3 (39.3–47) · 10 | 25.3 (24.1–26) · 5 | 6.08 · 2 | 55 (55–57) · 6 | 40 · 2 |
| ABS-CF | 4.35 (3.75–4.76) · 4 | 44 (36.2–47) · 7 | 28 · 3 | 16.1 · 1 | 90 (78–91) · 5 | 45 · 2 |
| ASA-CF | 3.91 (2.35–4.43) · 6 | 39.1 (39–45.8) · 7 | 27.5 (23–30.3) · 4 | 5.76 · 3 | 101 (97–103) · 5 | 65 (54–120) · 5 |
Each cell is the median of the products ranked, its middle half in brackets, and how many.
Where PETG-CF sits among the 128 rigid materials on file
Where is it in the landscape: stiffness against strength, heat resistance against price?
- PETG-CF: median, middle half as a cross
- a PETG-CF product
- an alternative
- another material
- beyond the scale
Tensile strength (XY) against tensile modulus (XY)
MPa, log scale
Tensile modulus (XY), GPa, log scale
HDT at 0.45 MPa against price
°C
Price, CAD/kg, log scale
Grey points are every other rigid material's medians; the alternatives are named.
The figure as a table
| Material | Tensile modulus (XY) | Tensile strength (XY) | Price | HDT at 0.45 MPa |
|---|---|---|---|---|
| PETG-CF (this material) | 3.7 GPa · 11 | 49.4 MPa · 12 | 41 CAD/kg · 3 | 72 °C · 11 |
| PETG | 1.69 GPa · 24 | 47 MPa · 34 | 26 CAD/kg · 11 | 70 °C · 32 |
| PETG-GF | 2.33 GPa · 3 | 45 MPa · 3 | 37 CAD/kg · 1 | 76 °C · 1 |
| PLA-CF | 2.8 GPa · 7 | 42.3 MPa · 10 | 40 CAD/kg · 2 | 55 °C · 6 |
| ABS-CF | 4.35 GPa · 4 | 44 MPa · 7 | 45 CAD/kg · 2 | 90 °C · 5 |
| ASA-CF | 3.91 GPa · 6 | 39.1 MPa · 7 | 65 CAD/kg · 5 | 101 °C · 5 |
Mechanical properties
Printed flat (XY), PETG-CF typically reaches a tensile strength of 49.4 MPa at a modulus of 3.7 GPa, and breaks at 5.7 % elongation. In bending, its flexural strength is typically 80 MPa at a flexural modulus of 3.21 GPa.
PETG-CF's products spread most in notched Charpy impact: the middle half runs 4–15.7 kJ/m²
How strong, stiff and tough are its products, and which stand out?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
- beyond the scale
One mark per product on each property's scale (zoomed where its products sit close together, as its label says); the band is the middle half of the products the median counts, and the line the median.
Hover or select a product to find it in every figure; its name opens its card on the Products page.
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| Tensile strength (XY) (MPa) | 12 | 49.4 | 43–53.7 | SUNLU PETG Carbon Fiber, 32 | Raise3D Hyper Speed PETG CF, 60 | 11 | 0 |
| Tensile modulus (XY) (GPa) | 11 | 3.7 | 2.93–4.08 | Eryone PETG-CF, 1.77 | 3DXTECH CarbonX Carbon Fiber PETG, 5.23 | 5 | 0 |
| Tensile strength (Z) (MPa) | 4 | 28.5 | 27–32 | Eryone PETG-CF, 24.1 | Polymaker Fiberon PETG-rCF08, 41.1 | 0 | 0 |
| Elongation at break (XY) (%) | 11 | 5.7 | 3.2–7.5 | Eryone PETG-CF, 1.9 | SUNLU PETG Carbon Fiber, 14 | 9 | 0 |
| Notched Charpy impact (kJ/m²) | 5 | 8 | 4–15.7 | Polymaker Fiberon PETG-rCF08, 4 | Nanovia PETG CF, 20 | 4 | 0 |
Every PETG-CF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
| Product | Notched Izod impact | Shore D hardness |
|---|---|---|
| SUNLU PETG Carbon Fiber | 7 kJ/m² | not published |
| Flashforge PETGCF10 | 3 kJ/m² | not published |
| 3D4Makers PETGCarbon | not published | 76.4 Shore D |
| FormFutura CarbonFil CF03 | 4.6 kJ/m²not described as printed | not published |
| SIDDAMENT PETG Carbon | 20 kJ/m²not described as printed | not published |
| 3DJake easyPETG CF | 4 kJ/m²not described as printed | not published |
| Nobufil PETG CF | 2 kJ/m²orientation not stated | not published |
Across the layers (Z), PETG-CF keeps 69 % of its flat strength and 71 % of its flat stiffness
What does a printed part lose across the layers (Z) against flat (XY), and is that usual?
- a product
- measured after annealing
- equal share: 100, 75, 50 and 25 %
- PETG-CF's median share
- an alternative
Tensile strength
Z keeps 69 % of XY, median of 3 products
flat (XY), MPa
Share kept: PETG-CF 69 % · PETG 69 % · ASA-CF 60 % · ABS-CF 59 % · PLA-CF 58 % · PETG-GF 47 %
Tensile modulus
Z keeps 71 % of XY, median of 3 products
flat (XY), GPa
Share kept: PETG-GF 90 % · PETG 88 % · PLA-CF 77 % · PETG-CF 71 % · ABS-CF 59 % · ASA-CF 56 %
Elongation at break
Z keeps 45 % of XY, median of 3 products
flat (XY), %
Share kept: ABS-CF 102 % · ASA-CF 91 % · PETG-GF 89 % · PETG 59 % · PETG-CF 45 % · PLA-CF 43 %
Each point is a product that publishes both from one sheet: below the 100 % ray it keeps less across the layers than flat. Under each plot, the median share its alternatives' products keep.
The figure as a table
| Product | Property | Flat (XY) | Across (Z) | Z as a share of XY |
|---|---|---|---|---|
| Bambu Lab PETG-CF | Tensile strength | 35 MPa | 29 MPa | 83 % |
| Polymaker Fiberon PETG-rCF08 | Tensile strength | 59.8 MPa | 41.1 MPa | 69 % |
| Eryone PETG-CF | Tensile strength | 48.7 MPa | 24.1 MPa, Z (X-Z) | 49 % |
| Bambu Lab PETG-CF | Tensile modulus | 2.46 GPa | 1.34 GPa | 54 % |
| Polymaker Fiberon PETG-rCF08 | Tensile modulus | 3.71 GPa | 2.65 GPa | 71 % |
| Eryone PETG-CF | Tensile modulus | 1.77 GPa | 1.7 GPa, Z (X-Z) | 96 % |
| Bambu Lab PETG-CF | Elongation at break | 10 % | 4.7 % | 45 % |
| Polymaker Fiberon PETG-rCF08 | Elongation at break | 5.7 % | 1.9 % | 33 % |
| Eryone PETG-CF | Elongation at break | 1.9 % | 1.5 %, Z (X-Z) | 79 % |
| PETG (alternative) | Tensile strength | 69 % · 13 | ||
| PETG-GF (alternative) | Tensile strength | 47 % · 1 | ||
| PLA-CF (alternative) | Tensile strength | 58 % · 5 | ||
| ABS-CF (alternative) | Tensile strength | 59 % · 3 | ||
| ASA-CF (alternative) | Tensile strength | 60 % · 4 | ||
| PETG (alternative) | Tensile modulus | 88 % · 10 | ||
| PETG-GF (alternative) | Tensile modulus | 90 % · 1 | ||
| PLA-CF (alternative) | Tensile modulus | 77 % · 5 | ||
| ABS-CF (alternative) | Tensile modulus | 59 % · 1 | ||
| ASA-CF (alternative) | Tensile modulus | 56 % · 4 | ||
| PETG (alternative) | Elongation at break | 59 % · 13 | ||
| PETG-GF (alternative) | Elongation at break | 89 % · 1 | ||
| PLA-CF (alternative) | Elongation at break | 43 % · 5 | ||
| ABS-CF (alternative) | Elongation at break | 102 % · 2 | ||
| ASA-CF (alternative) | Elongation at break | 91 % · 3 |
Tensile strength: one more product is in the median across the layers but gives no share, with no flat value of the same test from the same sheet: QIDI PETG CF (its flat and across values from two documents).
Flat and across the layers, property by property
Flat and across the layers
| Property | Printed flat (XY) | Across the layers (Z) | Z as a share of XY | ||
|---|---|---|---|---|---|
| Median | Products | Median | Products | ||
| Tensile strength MPa | 49.443–53.7 | 12 | 28.527–32 | 4 | 69 %3 products |
| Tensile modulus GPa | 3.72.93–4.08 | 11 | 1.7 | 3 | 71 %3 products |
| Elongation at break % | 5.73.2–7.5 | 11 | 1.9 | 3 | 45 %3 products |
| Flexural strength MPa | 8070–85 | 9 | 47.9 | 2 | 60 %2 products |
| Flexural modulus GPa | 3.212.99–3.78 | 9 | 1.59 | 2 | 48 %2 products |
The middle half of the products under each median. The share is each product's Z value as a part of its XY value, from one sheet and one state, and the median of those shares. Where it counts fewer products than the Z median, the others publish no flat value of the same test from the same sheet; the figure's table names them. How XY and Z differ.
Thermal properties
PETG-CF's HDT is typically 72 °C under 0.45 MPa and 68 °C under 1.8 MPa, with its glass transition typically at 69 °C. As published, Vicat softening is typically 82 °C.
Most PETG-CF products deflect at 71–75 °C under 0.45 MPa
Where do its products soften under load?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| HDT at 0.45 MPa (°C) | 11 | 72 | 71–75 | Polymaker Fiberon PETG-rCF08, 69 | QIDI PETG CF, 77 | 6 | 0 |
| HDT at 1.8 MPa (°C) | 6 | 68 | 66–69 | Raise3D Hyper Speed PETG CF, 65 | Recreus PET-G CF, 69 | 2 | 0 |
| Glass transition (Tg) (°C) | 10 | 69 | 68–79 | SUNLU PETG Carbon Fiber, 65 | Nanovia PETG CF, 80 | 0 | 0 |
Every PETG-CF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
Printing on the H2C
PETG-CF prints within the H2C's limits and softens near 72 °C, above its 65 °C chamber
What does printing it on the H2C take, and how hot can a part get?
- share of the products that accept each temperature
- what most products accept
- the H2C's limit, and beyond it
- a product
- PETG-CF: its products' median and middle half
- as published, under each sheet's own test
Printing it on the H2C
In service
°C
One temperature axis for the settings a print needs and the temperatures a part meets. A setting's shade is how many of the products whose sheets give a window accept each degree; the H2C's limit closes its row.
The figure as a table
| Setting or property | Most products, or the median | Products | H2C limit |
|---|---|---|---|
| Nozzle | 240–260 °C | 20 | 350 °C |
| Bed | 70 °C | 20 | 120 °C |
| Heated chamber | 35–50 °C | 3 | 65 °C |
| Drying | 40–80 °C, 2–12 h | 16 | — |
| HDT at 1.8 MPa | 68 °C (66–69 °C) | 6 | — |
| Glass transition (Tg) | 69 °C (68–79 °C) | 10 | — |
| HDT at 0.45 MPa | 72 °C (71–75 °C) | 11 | — |
| Vicat softening temperature | 72–85 °C | 12 | — |
Windows read from the Bambu Lab Filament Guide are not shaded: the guide speaks for every product that reads it.
| Setting | Most PETG-CF products | Bambu Lab Filament Guide (PETG-CF column) |
|---|---|---|
| Nozzle | 240–260 °C most products that give one | 240 - 270 ℃ |
| Bed | 70 °C most products that give one | Smooth PEI Plate (60 - 80 °C) Textured PEI Plate (60 - 80 °C) Cool Plate SuperTack (60-70 °C) |
| Heated chamber | none; sheets that give one say 35–50 °C 19 of 24 products | enclosure not needed |
| Drying | 40–80 °C, 2–12 h 15 of 24 products call for it; 9 more give it as optional | optional: 65 °C for 8 h |
| Nozzle type | hardened 14 of 24 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 10 more | hardened |
Where a product's own sheet is silent, its setting comes from a sheet it shares or from the Bambu Lab Filament Guide; each product's card says which.
After printing
One product publishes values measured after annealing, at 65 °C for 8 h.
the suggested annealing temperature of models printed with Bambu PETG-CF is 55 to 60 °C, and the time is 65 to 70 hours.
Bambu Lab PETG-CF, data sheet, p. 3
What makers say about printing it
Nozzle wear
Ruby or hardened nozzle recommended: Yes
Spectrum THE FILAMENT PETG CF, data sheet, p. 1
Warping and shrinkage
The specially formulated blend minimizes the risk of warping and nozzle sticking, while still providing a smooth and consistent print quality.
Bambu Lab PETG-CF, data sheet, p. 1
More from makers: moisture sensitivity, printing advice, supports and removal and odour and emissions
Moisture sensitivity
Fiberon™ PETG-rCF08 is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker Fiberon PETG-rCF08, data sheet, p. 1
Printing advice
After the printing process, it is recommended to dry the model in an oven at 70°C for 1-3 hours in order to increase the strength of the model.
Flashforge PETGCF10, data sheet, p. 3
Supports and removal
Supporting Material: Self-supporting, PVA
SIDDAMENT PETG Carbon Fiber, data sheet, p. 2
Odour and emissions
Odor / Low odor
QIDI PETG CF, data sheet, p. 3
Products
24 products from 21 makers; the most from FormFutura (2), SIDDAMENT (2) and Spectrum (2).
- Most documented: Bambu Lab PETG-CF, and 1 other that publishes as much.
- Highest tensile strength (XY): Raise3D Hyper Speed PETG CF, 60 MPa.
- Highest tensile strength (Z): Polymaker Fiberon PETG-rCF08, 41.1 MPa.
- Keeps the most strength across the layers: Bambu Lab PETG-CF, 83 % of its flat tensile strength (the median product keeps 69 %).
- Highest HDT at 0.45 MPa: 3DXTECH CarbonX Carbon Fiber PETG, 77 °C.
- Highest notched Charpy impact: Nanovia PETG CF, 20 kJ/m².
- Lowest price: eSUN PETG CF, 35 CAD/kg.
These are published values, not recommendations: the selector judges each product against your requirements.
Uses, limitations and chemicals
What it is sold for
PETG end use parts that do not require the full strength of carbon.
FormFutura CarbonFil CF03, data sheet, p. 1Structural parts, decorative items, toys, accessories, and figurines.
SUNLU PETG Carbon Fiber, data sheet, p. 1This makes it suitable for a variety of applications, including printing flower pots, fixtures, and water valve switches.
Eryone PETG-CF, data sheet, p. 1
What makers warn about
No. Carbon fiber reinforced filaments, including XPETG CF, are not certified for food contact. Any application requiring food safety should use a non-reinforced filament with confirmed food-contact compliance, such as PETG.
Extrudr XPETG CF, maker's product page or guide, p.1For an outdoor usage, it’s recommended either paint or apply a protective UV coating.
Nanovia PETG CF, data sheet, p. 1
Finish and accuracy
The 10% addition of carbon fibres enables to obtain matte surfaces of printed items, which greatly improves the aesthetic properties of printed items.
Spectrum PET-G Carbon, data sheet, p. 1This results in 3D prints with a magnificent carbon finish and no visible layers.
FormFutura CarbonFil CF03, data sheet, p. 1It prints with great precision and superb layer adhesion.
FormFutura CarbonFil CF03, data sheet, p. 1dimensional stability, precise details
QIDI PETG CF, data sheet, p. 2
Chemicals and environment
| Exposure | What makers say |
|---|---|
| Water solubility | Insoluble, in its one statement |
| Acid resistance | Not resistant, in its one statement |
| Alkali resistance | Not resistant, in its one statement |
| Organic solvent resistance | Limited, in 1 of 2 statements; the other gives no rating |
| Oil and grease resistance | Limited, in its one statement |
| Flammability | Flammable, in its one statement |
| UV and outdoor | Described in words, with no rating, in its one statement |
Makers rarely give the concentration, temperature or duration: treat them as indications, not design data. Each product's statements are on its card.
Density and price
PETG-CF's density is typically 1,290 kg/m³, the middle half 1,260–1,320 kg/m³, across 23 products. PETG-CF typically costs 41 CAD/kg, across the 3 products with a regular price in the sample; the lowest is eSUN PETG CF at 35 CAD/kg. QIDI Canada lists QIDI PETG CF, out of stock when sampled, with no regular price recorded.
| Product | Price |
|---|---|
| Bambu Lab PETG-CF | 41 CAD/kg |
| Polymaker Fiberon PETG-rCF08 | 56 CAD/kg |
| eSUN PETG CF | 35 CAD/kg |
Regular prices, never sale prices, from 9 Canadian shops and 10 foreign shops, sampled 10 Sep–20 Oct 2026, not live; shipping and tax are not included.
Other properties, as published
12 more properties are published, each under its own sheet's test conditions, so they are listed, not ranked.
The 12 properties, lowest to highest
| Property | Products | Lowest–highest |
|---|---|---|
| Fibre content | 16 | 3–20 % |
| Melt mass-flow rate | 9 | 5–19.3 g/10 min |
| Water absorption | 8 | 0.1–1 % |
| Melting temperature | 3 | 190–225 °C |
| Decomposition temperature | 2 | 370–425 °C |
| Elongation at yield | 2 | 3–3.8 % |
| Impact strength, test unclear | 2 | 3–8.5 kJ/m² |
| Melt volume-flow rate | 2 | 3.7–35 cm³/10 min |
| Tensile strain at strength | 2 | 2.3–2.7 % |
| Continuous service temperature | 1 | 80 °C |
| Hardness | 1 | 71 Shore (scale not specified by source) |
| Mould shrinkage | 1 | 0.2–0.3 % |
Sources
44 documents from 21 publishers (29 data sheets, 10 makers' product pages and guides, 4 safety data sheets and 1 printer document), read 10 Sep–19 Oct 2026. Each value on PETG-CF's Products page names its document and page, and links to the original.
Bambu Lab, H2C Filamant Printing Guide (the H2C's printer guide): print settings for 23 products.
The Bambu Lab Filament Guide (print settings per material type): read for 19 products whose own sheets are silent.
Every document (44), by publisher
| Publisher | Documents | Values | Products |
|---|---|---|---|
| Spectrum | 6 | 15 | 2 |
| Extrudr | 3 | 38 | 1 |
| FormFutura | 3 | 23 | 2 |
| Bambu Lab | 3 | 22 | 1 |
| 3DXTECH | 3 | 9 | 1 |
| QIDI | 2 | 24 | 1 |
| 3DJake | 2 | 16 | 1 |
| SIDDAMENT | 2 | 14 | 2 |
| SUNLU | 2 | 13 | 1 |
| Fiberlogy | 2 | 12 | 1 |
| Recreus | 2 | 11 | 1 |
| 3D4Makers | 2 | 10 | 1 |
| and 9 more publishers, with 10 documents | |||
- 3D4Makers, PETG Carbon Filament
- 3D4Makers, Technical Data Sheet 3D Printing Filament PETG Carbon Filament
- 3DJake, 3DJake easyPETG CF Filaments
- 3DJake, Technical Data Sheet 3DJAKE easyPETG CF
- 3DXTECH, CarbonX Carbon Fiber PETG safety data sheet
- 3DXTECH, CARBONX™ PETG+CF
- 3DXTECH, Technical Data Sheet: CarbonX™ Carbon Fiber PETG 3D Printing Filament
- Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CF
- Bambu Lab, Bambu Lab Filament Guide
- Bambu Lab, Bambu Lab PETG-CF safety data sheet
- Bambu Lab, H2C Filamant Printing Guide | Bambu Lab Wiki
- Bambu Lab, PETG-CF official maker product page
- Eryone, Technical Data Sheet (TDS) PETG-CF
- eSUN, ePETG-CF Technical Data Sheet
- Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF
- Extrudr, TECHNICAL DATA SHEET XPETG CF
- Extrudr, XPETG CF official maker product page
- Fiberlogy, PETG+CF Filament
- Fiberlogy, TECHNICAL DATA SHEET Fiberlogy PETG+CF
- Flashforge, Technical Data Sheet PETGCF10 Filament
- FormFutura, Technical Data Sheet CarbonFil
- FormFutura, TECHNICAL DATA SHEET CarbonFil CF03
- FormFutura, Technical Data Sheet CarbonFil™
- iSANMATE, PETG CF Filament Technical Data Sheet
- Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanovia
- Nanovia, PETG CF official material safety data sheet
- Nobufil, Technical Datasheet PETG CF
- Polymaker, Fiberon PETG-rCF08 Technical Data Sheet
- QIDI, QIDI Filament Guide | Choose the Right Filament
- QIDI, Technical Data Sheet QIDI PETG-CF
- Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheet
- Recreus, TECHNICAL DATA SHEET PET-G CF
- Recreus, TECHNICAL DATA SHEET PET-G CF
- SIDDAMENT, PETG Carbon Fiber - Technical Datasheet
- SIDDAMENT, PETG CF Technical Data Sheet
- Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Tech
- Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIO
- Spectrum, KARTA TECHNICZNA PET-G Carbon
- Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29
- Spectrum, TECHNICAL DATA SHEET PET-G Carbon
- Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CF
- Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CF
- SUNLU, SUNLU PETG Carbon Fiber safety data sheet
- SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiber