ASA-CF
Carbon-Fiber-Reinforced Acrylonitrile Styrene Acrylate
17 products from 15 makers. Bambu Lab sells its own filament of this material for the H2C.
- Tensile modulus (XY)
- 3.91GPa
- 6 products · middle half 2.35–4.43
- Tensile strength (XY)
- 39.1MPa
- 7 products · middle half 39–45.8
- Tensile strength (Z)
- 27.5MPa
- 4 products · middle half 23–30.3
- Notched Charpy impact
- 5.76kJ/m²
- 3 products · 5.5–6.2
- HDT at 0.45 MPa
- 101°C
- 5 products · middle half 97–103
- Price
- 65CAD/kg
- 5 products · middle half 54–120
ASA-CF is carbon-fibre-filled acrylonitrile styrene acrylate. Makers sell it for durable large models and outdoor parts, citing UV stability. Its HDT at 0.45 MPa is 101 °C, and across the layers it keeps 56 % of its flat stiffness. On the H2C it needs a hardened nozzle, and makers advise drying it before printing.
Partly documented Notched Charpy impact rests on 3 products and tensile strength (Z) on 4 products. Each figure is the median of the products that publish it comparably, and beside it the middle half of them; a value on a test bar no document describes as printed, or with no stated test load, is set apart, except a heat deflection of a plastic that cannot crystallise, which its glass transition sets, unless its document points to a moulded or resin bar.
On the H2C
Printing in full- Nozzle
- 240–270 °C
- most products that give one
- Bed
- 90–110 °C
- most products that give one
- Heated chamber
- 45–60 °C
- both that give one
- Drying
- 60–90 °C, 2–8 h
- 10 of 17 products call for it; 7 more give it as optional
- Nozzle type
- hardened
- 10 of 17 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 7 more
No product's setting is beyond the H2C's limits: nozzle 350 °C, bed 120 °C, heated chamber 65 °C.
Among the materials
Carbon fibre raises ASA's HDT at 0.45 MPa by 6 °C: ASA-CF's HDT at 0.45 MPa is 101 °C against 96 °C. Against ASA-GF, ASA-CF is 69 % stiffer and 12 % stronger across the layers, and its HDT at 0.45 MPa is 8 °C higher. Among the materials, ASA-CF has a high tensile modulus (XY) and a low density: both are in the top or bottom quarter of the materials that publish them. The rest of its key properties sit in the middle half.
Against its alternatives, ASA-CF has the lowest notched Charpy impact
How does it compare with what an engineer would buy instead?
- ASA-CF: its products' median and middle half
- an alternative
- lowest to highest
- each material's median (top row)
- set apart: test bar not described as printed, or no stated load
Each row is a material, each column a property: the bar is the middle half of a material's products, the tick their median, the hairline their lowest to highest; the ticks above the rows are every material's median.
The figure as a table
| Material | Modulus (XY) (GPa) | Strength (XY) (MPa) | Strength (Z) (MPa) | Notched Charpy (kJ/m²) | HDT 0.45 MPa (°C) | Price (CAD/kg) |
|---|---|---|---|---|---|---|
| ASA-CF (this material) | 3.91 (2.35–4.43) · 6 | 39.1 (39–45.8) · 7 | 27.5 (23–30.3) · 4 | 5.76 · 3 | 101 (97–103) · 5 | 65 (54–120) · 5 |
| ASA | 2.1 (2–2.32) · 13 | 38.6 (35.9–41.5) · 15 | 25.8 (21.5–28.9) · 7 | 12 (10.5–12.9) · 5 | 96 (92–100) · 12 | 39 (39–57) · 5 |
| ASA-GF | 2.31 · 2 | 39 · 3 | 24.6 · 2 | 8 as published (1) | 93 · 2 | 96 · 1 |
| ABS-CF | 4.35 (3.75–4.76) · 4 | 44 (36.2–47) · 7 | 28 · 3 | 16.1 · 1 | 90 (78–91) · 5 | 45 · 2 |
| ABS-GF | 2.75 (2.15–3.6) · 6 | 46.5 (36.6–51.7) · 7 | 29 · 3 | 6.55 · 2 | 98 (90–99) · 6 | 39 · 1 |
| PA12-CF | 3.31 (1.97–8) · 5 | 65 (48.5–79.5) · 8 | 33.1 · 2 | 16.3 (13.7–17.8) · 4 | 131 (111–160) · 7 | 300 · 1 |
Each cell is the median of the products ranked, its middle half in brackets, and how many.
Where ASA-CF sits among the 128 rigid materials on file
Where is it in the landscape: stiffness against strength, heat resistance against price?
- ASA-CF: median, middle half as a cross
- a ASA-CF product
- an alternative
- another material
- beyond the scale
Tensile strength (XY) against tensile modulus (XY)
MPa, log scale
Tensile modulus (XY), GPa, log scale
HDT at 0.45 MPa against price
°C
Price, CAD/kg, log scale
Grey points are every other rigid material's medians; the alternatives are named.
The figure as a table
| Material | Tensile modulus (XY) | Tensile strength (XY) | Price | HDT at 0.45 MPa |
|---|---|---|---|---|
| ASA-CF (this material) | 3.91 GPa · 6 | 39.1 MPa · 7 | 65 CAD/kg · 5 | 101 °C · 5 |
| ASA | 2.1 GPa · 13 | 38.6 MPa · 15 | 39 CAD/kg · 5 | 96 °C · 12 |
| ASA-GF | 2.31 GPa · 2 | 39 MPa · 3 | 96 CAD/kg · 1 | 93 °C · 2 |
| ABS-CF | 4.35 GPa · 4 | 44 MPa · 7 | 45 CAD/kg · 2 | 90 °C · 5 |
| ABS-GF | 2.75 GPa · 6 | 46.5 MPa · 7 | 39 CAD/kg · 1 | 98 °C · 6 |
| PA12-CF | 3.31 GPa · 5 | 65 MPa · 8 | 300 CAD/kg · 1 | 131 °C · 7 |
Mechanical properties
Printed flat (XY), ASA-CF typically reaches a tensile strength of 39.1 MPa at a modulus of 3.91 GPa, and breaks at 6.3 % elongation. In bending, its flexural strength is typically 78 MPa at a flexural modulus of 3.74 GPa.
ASA-CF's products spread most in elongation at break: the middle half runs 2.1–14 %
How strong, stiff and tough are its products, and which stand out?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
- beyond the scale
One mark per product on each property's scale (zoomed where its products sit close together, as its label says); the band is the middle half of the products the median counts, and the line the median.
Hover or select a product to find it in every figure; its name opens its card on the Products page.
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| Tensile strength (XY) (MPa) | 7 | 39.1 | 39–45.8 | Bambu Lab ASA-CF, 34 | QIDI ASA-CF20 Core, 50.1 | 9 | 0 |
| Tensile modulus (XY) (GPa) | 6 | 3.91 | 2.35–4.43 | Flashforge ASACF10, 0.85 | 3DXTECH CarbonX CF ASA, 5.36 | 2 | 0 |
| Tensile strength (Z) (MPa) | 4 | 27.5 | 23–30.3 | Eryone ASA-CF, 17 | QIDI ASA-CF20 Core, 31 | 0 | 0 |
| Elongation at break (XY) (%) | 6 | 6.3 | 2.1–14 | QIDI ASA-CF20 Core, 1.64 | SIDDAMENT ASA CF, 16 | 7 | 0 |
Every ASA-CF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
| Product | Notched Charpy impact | Notched Izod impact | Shore D hardness |
|---|---|---|---|
| Bambu Lab ASA-CF | 6.2 kJ/m²after annealing | not published | not published |
| Spectrum ASA-X CF10 | 5.4 kJ/m²not described as printed | not published | not published |
| Flashforge ASACF10 | not published | 10.5 kJ/m² | not published |
| Fillamentum ASA CF10 | not published | not published | 74 Shore D |
| Polymaker FIBERON ASA | 5.5 kJ/m² | not published | not published |
| FormFutura ApolloX CF10 | 5.4 kJ/m²not described as printed | not published | not published |
| SIDDAMENT ASA Carbon | not published | 65 kJ/m²not described as printed | not published |
| QIDI ASA-CF20 Core | 5.76 kJ/m² | not published | not published |
| Nobufil ASAx CF | not published | 2.6 kJ/m²orientation not stated | not published |
| 3DJake ASA CF | 9 kJ/m²not described as printed | 9.5 kJ/m²not described as printed | not published |
In grey, a value a product reads from a data sheet it shares, where its own sheet is silent.
Across the layers (Z), ASA-CF keeps 60 % of its flat strength and 56 % of its flat stiffness
What does a printed part lose across the layers (Z) against flat (XY), and is that usual?
- a product
- measured after annealing
- equal share: 100, 75, 50 and 25 %
- ASA-CF's median share
- an alternative
Tensile strength
Z keeps 60 % of XY, median of 4 products
flat (XY), MPa
Share kept: ASA-GF 67 % · ABS-GF 63 % · ASA-CF 60 % · ABS-CF 59 % · ASA 59 % · PA12-CF 46 %
Tensile modulus
Z keeps 56 % of XY, median of 4 products
flat (XY), GPa
Share kept: ASA 88 % · ASA-GF 82 % · ABS-GF 76 % · ABS-CF 59 % · ASA-CF 56 % · PA12-CF 55 %
Elongation at break
Z keeps 91 % of XY, median of 3 products
flat (XY), %
Share kept: PA12-CF 106 % · ABS-CF 102 % · ASA-CF 91 % · ABS-GF 80 % · ASA 50 % · ASA-GF 36 %
Each point is a product that publishes both from one sheet: below the 100 % ray it keeps less across the layers than flat. Under each plot, the median share its alternatives' products keep.
The figure as a table
| Product | Property | Flat (XY) | Across (Z) | Z as a share of XY |
|---|---|---|---|---|
| Bambu Lab ASA-CF | Tensile strength | 34 MPa | 30 MPa | 88 % |
| Eryone ASA-CF | Tensile strength | 39.1 MPa | 17 MPa, Z (X-Z) | 43 % |
| Polymaker FIBERON ASA CF08 | Tensile strength | 43.5 MPa | 25 MPa | 57 % |
| QIDI ASA-CF20 Core | Tensile strength | 50.1 MPa | 31 MPa | 62 % |
| Bambu Lab ASA-CF | Tensile modulus | 4.2 GPa | 2.29 GPa | 55 % |
| Eryone ASA-CF | Tensile modulus | 1.93 GPa | 1.8 GPa, Z (X-Z) | 93 % |
| Polymaker FIBERON ASA CF08 | Tensile modulus | 3.61 GPa | 1.9 GPa | 53 % |
| QIDI ASA-CF20 Core | Tensile modulus | 4.5 GPa | 2.57 GPa | 57 % |
| Bambu Lab ASA-CF | Elongation at break | 9.6 % | 4.4 % | 46 % |
| Polymaker FIBERON ASA CF08 | Elongation at break | 1.8 % | 2.7 % | 150 % |
| QIDI ASA-CF20 Core | Elongation at break | 1.64 % | 1.5 % | 91 % |
| ASA (alternative) | Tensile strength | 59 % · 5 | ||
| ASA-GF (alternative) | Tensile strength | 67 % · 2 | ||
| ABS-CF (alternative) | Tensile strength | 59 % · 3 | ||
| ABS-GF (alternative) | Tensile strength | 63 % · 3 | ||
| PA12-CF (alternative) | Tensile strength | 46 % · 2 | ||
| ASA (alternative) | Tensile modulus | 88 % · 5 | ||
| ASA-GF (alternative) | Tensile modulus | 82 % · 2 | ||
| ABS-CF (alternative) | Tensile modulus | 59 % · 1 | ||
| ABS-GF (alternative) | Tensile modulus | 76 % · 3 | ||
| PA12-CF (alternative) | Tensile modulus | 55 % · 1 | ||
| ASA (alternative) | Elongation at break | 50 % · 5 | ||
| ASA-GF (alternative) | Elongation at break | 36 % · 1 | ||
| ABS-CF (alternative) | Elongation at break | 102 % · 2 | ||
| ABS-GF (alternative) | Elongation at break | 80 % · 3 | ||
| PA12-CF (alternative) | Elongation at break | 106 % · 2 |
Elongation at break: one more product is in the median across the layers but gives no share, with no flat value of the same test from the same sheet: Eryone ASA-CF (no flat value compared).
Flat and across the layers, property by property
Flat and across the layers
| Property | Printed flat (XY) | Across the layers (Z) | Z as a share of XY | ||
|---|---|---|---|---|---|
| Median | Products | Median | Products | ||
| Tensile strength MPa | 39.139–45.8 | 7 | 27.523–30.3 | 4 | 60 %4 products |
| Tensile modulus GPa | 3.912.35–4.43 | 6 | 2.11.88–2.36 | 4 | 56 %4 products |
| Elongation at break % | 6.32.1–14 | 6 | 2.251.73–3.13 | 4 | 91 %3 products |
| Flexural strength MPa | 7870.5–80 | 7 | 39.8 | 2 | 57 %2 products |
| Flexural modulus GPa | 3.743.27–4.54 | 5 | 1.55 | 2 | 45 %2 products |
The middle half of the products under each median. The share is each product's Z value as a part of its XY value, from one sheet and one state, and the median of those shares. Where it counts fewer products than the Z median, the others publish no flat value of the same test from the same sheet; the figure's table names them. How XY and Z differ.
Thermal properties
ASA-CF's HDT is typically 101 °C under 0.45 MPa and 96 °C under 1.8 MPa, against a glass transition of 105–107 °C. As published, Vicat softening is typically 102 °C.
Most ASA-CF products deflect at 97–103 °C under 0.45 MPa
Where do its products soften under load?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
- beyond the scale
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| HDT at 0.45 MPa (°C) | 5 | 101 | 97–103 | Flashforge ASACF10, 88 | Bambu Lab ASA-CF, 110 | 4 | 0 |
| HDT at 1.8 MPa (°C) | 5 | 96 | 95–97 | Spectrum ASA-X CF10, 95 | Bambu Lab ASA-CF, 102 | 1 | 0 |
Every ASA-CF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
| Product | Glass transition (Tg) |
|---|---|
| 3DXTECH CarbonX CF ASA | 105 °C |
| Polymaker FIBERON ASA | 107 °C |
Printing on the H2C
ASA-CF prints within the H2C's limits and softens near 101 °C, above its 65 °C chamber
What does printing it on the H2C take, and how hot can a part get?
- share of the products that accept each temperature
- what most products accept
- the H2C's limit, and beyond it
- a product
- ASA-CF: its products' median and middle half
- as published, under each sheet's own test
Printing it on the H2C
In service
°C
One temperature axis for the settings a print needs and the temperatures a part meets. A setting's shade is how many of the products whose sheets give a window accept each degree; the H2C's limit closes its row.
The figure as a table
| Setting or property | Most products, or the median | Products | H2C limit |
|---|---|---|---|
| Nozzle | 240–270 °C | 15 | 350 °C |
| Bed | 90–110 °C | 15 | 120 °C |
| Heated chamber | 25–60 °C; 45–60 °C | 2 | 65 °C |
| Drying | 60–90 °C, 2–8 h | 10 | — |
| HDT at 1.8 MPa | 96 °C (95–97 °C) | 5 | — |
| HDT at 0.45 MPa | 101 °C (97–103 °C) | 5 | — |
| Vicat softening temperature | 90–111 °C | 9 | — |
| Glass transition (Tg) | 106 °C | 2 | — |
Windows read from the Bambu Lab Filament Guide are not shaded: the guide speaks for every product that reads it.
| Setting | Most ASA-CF products | Bambu Lab Filament Guide (ASA-CF column) |
|---|---|---|
| Nozzle | 240–270 °C most products that give one | 250 - 290 ℃ |
| Bed | 90–110 °C most products that give one | Smooth PEI Plate(90 - 100 °C) Textured PEI Plate(90 - 100 °C) |
| Heated chamber | 45–60 °C both that give one | enclosure required |
| Drying | 60–90 °C, 2–8 h 10 of 17 products call for it; 7 more give it as optional | optional: 80 °C for 8 h |
| Nozzle type | hardened 10 of 17 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 7 more | hardened |
Where a product's own sheet is silent, its setting comes from a sheet it shares or from the Bambu Lab Filament Guide; each product's card says which.
After printing
One product publishes values measured after annealing, at 80 °C for 12 h.
What makers say about printing it
Nozzle wear
Ruby or hardened nozzle recommended: Yes
Spectrum THE FILAMENT ASA CF, data sheet, p. 1
Printing advice
Additionally, a nozzle diameter of at least 0.6 mm should be used to prevent clogging and ensure smooth extrusion.
Extrudr DURAPRO ASA CF, data sheet, p. 1
More from makers: moisture sensitivity, supports and removal, warping and shrinkage, adhesion between layers and odour and emissions
Moisture sensitivity
As the ASACF10 filament absorbs moisture easily due to the added carbon fiber, it should be dried before being used.
Flashforge ASACF10, data sheet, p. 3
Supports and removal
High heatbed temperatures and glue stick can cause strong adhesion between the print and the build plate. Please allow the print to cool down to room temperature naturally for easier removal and to avoid damage to the model. For more details, please refer to: Work After Printing Finished on WIKI.
Bambu Lab ASA-CF, maker's product page or guide, p. 1
Warping and shrinkage
At the same time, it also reduces the impact of curled edges during the printing process, greatly improving the dimensional accuracy and stability of the model.
Eryone ASA-CF, data sheet, p. 1
Adhesion between layers
DuraPro ASA CF is optimised for good layer adhesion, thermal stability, better flow properties and lower warping.
Extrudr DURAPRO ASA CF, data sheet, p. 1
Odour and emissions
Fiberon™ ASA-CF08 may release odors during printing.
Polymaker FIBERON ASA CF08, data sheet, p. 1
Products
17 products from 15 makers; the most from SIDDAMENT (2) and Spectrum (2).
- Most documented: Polymaker FIBERON ASA CF08, with values for more properties than any other.
- Highest tensile strength (XY): QIDI ASA-CF20 Core, 50.1 MPa.
- Highest tensile strength (Z): QIDI ASA-CF20 Core, 31 MPa.
- Keeps the most strength across the layers: Bambu Lab ASA-CF, 88 % of its flat tensile strength (the median product keeps 60 %).
- Highest HDT at 0.45 MPa: Bambu Lab ASA-CF, 110 °C, measured after annealing at 80 °C for 12 h.
- Highest notched Charpy impact: Bambu Lab ASA-CF, 6.2 kJ/m², measured after annealing at 80 °C for 12 h.
- Lowest price: Eryone ASA-CF, 40 CAD/kg.
These are published values, not recommendations: the selector judges each product against your requirements.
Uses, limitations and chemicals
What it is sold for
It also has heat resistance close to 100°C, which is the first choice of outdoor reinforcement material.
Polymaker FIBERON ASA CF08, data sheet, p. 1Composite reinforced with 12% carbon fibre for high-strength applications
3DJake ASA CF, maker's product page or guide, p. 1The material is reinforced with carbon fibres, making it ideal for mechanically highly stressed components.
Extrudr DURAPRO ASA CF, data sheet, p. 1
What makers warn about
Fiberon™ ASA-CF08 contains 8% carbon fiber as reinforcement, the filament itself is easy to be brittle, please make sure that the bending diameter is more than 60mm when using it.
Polymaker FIBERON ASA CF08, data sheet, p. 1Yes. Like all ASA filaments, it releases VOCs such as styrene when heated. Always print in a well-ventilated space, and ideally use an enclosure with a filtration system.
Polymaker FIBERON ASA CF08, maker's product page or guide, p. 1
Finish and accuracy
when the printing speed is too high, the melt flow state will become unstable, and the filaments extruded from the nozzle will no longer have the skin-core structure anymore, which can cause the rough surface of the printed part.
QIDI ASA-CF20 Core, data sheet, p. 5All of this, combined with a carbon matt surface that effectively masks the layers.
Spectrum ASA-X CF10, data sheet, p. 1A state-of-the-art manufacturing process achieves very low manufacturing tolerances, which leads to impressive printing results for all FDM 3D printers.
Fabru ASA CF10, maker's product page or guide, p. 1low diameter and roundness tolerances
Fabru ASA CF10, maker's product page or guide, p. 1
Chemicals and environment
| Exposure | What makers say |
|---|---|
| Water solubility | Insoluble, in its one statement |
| Acid resistance | Resistant, in its one statement |
| Alkali resistance | Resistant, in its one statement |
| Organic solvent resistance | Limited, in its one statement |
| Oil and grease resistance | Limited, in its one statement |
| Flammability | Flammable, in 1 of 2 statements; the other gives no rating |
| UV and outdoor | Described in words, with no rating, in all 7 statements |
On food contact, disposal and safety, as makers state them:
Local exhaust is preferred. Product as shipped is not a combustible dust; mechanical handling can cause the formation of dusts.
Safety 3DXTECH CarbonX CF ASA, safety data sheet, p. 2Waste or unused product may be discarded in accordance with state, federal, and local regulations.
Disposal and circularity 3DXTECH CarbonX CF ASA, safety data sheet, p. 3
Makers rarely give the concentration, temperature or duration: treat them as indications, not design data. Each product's statements are on its card.
Density and price
ASA-CF's density is typically 1,100 kg/m³, the middle half 1,080–1,110 kg/m³, across 16 products. ASA-CF typically costs 65 CAD/kg, the middle half 54–120 CAD/kg, across the 5 products with a regular price in the sample; the lowest is Eryone ASA-CF at 40 CAD/kg.
Regular prices, never sale prices, from 9 Canadian shops and 10 foreign shops, sampled 10 Sep–20 Oct 2026, not live; shipping and tax are not included.
Other properties, as published
10 more properties are published, each under its own sheet's test conditions, so they are listed, not ranked.
The 10 properties, lowest to highest
| Property | Products | Lowest–highest |
|---|---|---|
| Fibre content | 11 | 3–20 % |
| Melt mass-flow rate | 8 | 1.74–16 g/10 min |
| Water absorption | 4 | 0.33–0.5 % |
| Melting temperature | 3 | 135–250 °C |
| Continuous service temperature | 2 | 85 °C |
| Mould shrinkage | 2 | 0.3 % |
| Decomposition temperature | 1 | 328 °C |
| Elongation at yield | 1 | 9.19 % |
| Hardness | 1 | 105 Rockwell R |
| Surface resistivity | 1 | 1 × 10¹² Ω |
Sources
31 documents from 14 publishers (19 data sheets, 9 makers' product pages and guides, 2 safety data sheets and 1 printer document), read 10 Sep–19 Oct 2026. Each value on ASA-CF's Products page names its document and page, and links to the original.
Bambu Lab, H2C Filamant Printing Guide (the H2C's printer guide): print settings for 16 products.
The Bambu Lab Filament Guide (print settings per material type): read for 13 products whose own sheets are silent.
Every document (31), by publisher
| Publisher | Documents | Values | Products |
|---|---|---|---|
| Spectrum | 5 | 19 | 3 |
| Bambu Lab | 3 | 21 | 1 |
| 3DXTECH | 3 | 9 | 1 |
| Fabru | 3 | 9 | 1 |
| Polymaker | 2 | 25 | 1 |
| SIDDAMENT | 2 | 17 | 2 |
| QIDI | 2 | 16 | 1 |
| 3DJake | 2 | 12 | 1 |
| Extrudr | 2 | 12 | 1 |
| Nobufil | 1 | 13 | 1 |
| Eryone | 1 | 12 | 1 |
| Fillamentum | 1 | 11 | 1 |
| and 2 more publishers, with 2 documents | |||
- 3DJake, 3DJAKE ASA CF Black, 1.75 mm / 1000 g
- 3DJake, Technical Data Sheet 3DJAKE ASA CF
- 3DXTECH, CARBONX™ ASA+CF
- 3DXTECH, Safety Data Sheet: CarbonX™ CF-ASA
- 3DXTECH, Technical Data Sheet: CarbonX™ Carbon Fiber ASA 3D Printing Filament
- Bambu Lab, ASA-CF official maker product page
- Bambu Lab, Bambu Filament Technical Data Sheet - ASA-CF
- Bambu Lab, Bambu Lab ASA-CF safety data sheet
- Bambu Lab, Bambu Lab Filament Guide
- Bambu Lab, H2C Filamant Printing Guide | Bambu Lab Wiki
- Eryone, Technical Data Sheet (TDS) ASA-CF
- Extrudr, TECHNICAL DATA SHEET DURAPRO ASA CF
- Extrudr, TECHNICAL DATA SHEET DURAPRO ASA CF
- Fabru, Acrilonitrile stirene acrilico estere fibra di carbonio 10% (ASA CF10)
- Fabru, Acrylonitrile Styrène Ester Acrylique Fibre de Carbone 10% (ASA CF10)
- Fabru, purefil ASA CF10 schwarz 1kg 1.75mm Refill
- Fillamentum, ASA CF10 Carbon
- Flashforge, Technical Data Sheet ASACF10 Filament
- FormFutura, Technical Data Sheet ApolloX CF10
- Nobufil, Technical Datasheet ASAx CF
- Polymaker, FIBERON ASA CF08
- Polymaker, FIBERON ASA CF08 official maker product page
- QIDI, QIDI Filament Guide | Choose the Right Filament
- QIDI, Technical Data Sheet QIDI ASA-CF20 Core
- SIDDAMENT, ASA Carbon Fiber - Technical Datasheet
- SIDDAMENT, ASA CF Technical Data Sheet
- Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIO
- Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29
- Spectrum, TECHNICAL DATA SHEET ASA-X CF10
- Spectrum, TECHNICAL DATA SHEET THE FILAMENT ASA CF
- Spectrum, TECHNICAL DATA SHEET THE FILAMENT ASA CF