PETG-CF
24 products from 21 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
24 products
Key
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- from the Bambu Lab Filament Guide
- Izod where no Charpy is published
- sold as toughened
- hardened nozzle
- not published
How the numbers are worked out
Bambu Lab PETG-CFStrength XY, MPa35Strength Z, MPa29Modulus XY, GPa2.46Charpy notched, kJ/m²15.7HDT 0.45, °C74HDT 1.8, °C68Price, CAD/kg41Nozzle, °C240–270Bed, °C65–75Chamber, °C35–50Drying, °C, h658 h
Bambu Lab PETG-CFBambu Lab
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CF21 valuesUnless a row says otherwise: printed specimendryDried before testing (see preparation)annealed at 65 °C for 8 hAll the specimens were annealed and dried at 65 °C for 8 h before testingprint settingsSpecimen Printing Conditions Subjects Data Nozzle Temperature 255 °C Bed Temperature 70 °C Printing Speed 150 mm/s Infill Density 100% * All the specimens were printed at the following settings: Nozzle Temperature = 255 °C, Printing Speed = 150 mm/s, Bed Temperature = 70 °C, Infill Density = 100%. All the specimens were annealed and dried at 65 °C for 8 h before testing. And | |||
| Tensile modulus XY | 2460 ± 230 MPap. 2: Young's Modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 1340 ± 150 MPap. 2: Young's Modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 35 ± 5 MPap. 2: Tensile Strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 29 ± 4 MPap. 2: Tensile Strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 10.4 ± 0.6 %p. 2: Breaking Elongation Rate (X-Y) | ISO 527, GB/T 1040 | in the median |
| Elongation at break Z | 4.7 ± 0.4 %p. 2: Breaking Elongation Rate (Z) | ISO 527, GB/T 1040 | in the median |
| Flexural modulus XY | 2910 ± 260 MPap. 2: Bending Modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 1560 ± 180 MPap. 2: Bending Modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 70 ± 5 MPap. 2: Bending Strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 48 ± 4 MPap. 2: Bending Strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 41.2 ± 2.6 kJ/m²;p. 2: Impact Strength (X-Y) — unnotched | ISO 179, GB/T 1043 | not in the median: unnotched |
| Charpy impact strength XY | 15.7 ±1.6 kJ/m²p. 2: Impact Strength (X-Y) — notched | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength Z | 10.7 ± 1.6 kJ/m²p. 2: Impact Strength (Z) | ISO 179, GB/T 1043 | not in the median: notch not stated |
| HDT at 0.45 MPa | 74 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 0.45 MPa | in the median |
| HDT at 1.8 MPa | 68 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 1.8 MPa | in the median |
| Glass transition temperature | 68 °Cp. 2: Glass Transition Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | in the median |
| Vicat softening temperature | 85 °Cp. 2: Vicar Softening Temperature | ISO 306, GB/T 1633 | |
| Melting temperature | 225 °Cp. 2: Melting Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Density | 1.25 g/cm³p. 2: Density | specimen not stated, ISO 1183 | |
| Water absorption | 0.30 %p. 2: Saturated Water Absorption Rate | no standard namedAs the sheet prints it: te 25 °C, 55% RH | |
| Melt mass-flow rate | 19.3 ± 2.4 g/10 minp. 2: Melt Index | specimen not stated, no standard namedAs the sheet prints it: 250 °C, 2.16 kg | |
| Also named without a value: crystallization temperature. | |||
| Bambu Lab, Bambu Lab PETG-CF safety data sheet1 value | |||
| Fibre content | 5-10 %p. 4: Carbon Fiber | no standard stated | |
Print settings
- Nozzle
- 240–270 °Cown data sheet
- Bed
- 65–75 °Cown data sheet
- Heated chamber
- 35–50 °Cown data sheet
- Drying
- 65 °C for 8 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
- Annealing
- 65 °C for 8 hown data sheet
Its print profile, in the documents' words
- Nozzle 240 - 270 °C; Bed 65 - 75 °C; Chamber 35 - 50 °C; Drying Blast Drying Oven: 65 °C, 8 hBambu Lab, Bambu Filament Technical Data Sheet - PETG-CFRecommended printing settings
Price
41 CAD/kgits one regular price in the sample
4 listings: 1 in its price, 3 with no regular price per kilogram recorded
- Bambu Lab Canada: 45 per kg, sale pricePETG-CF - Black (31100) / Filament with spool / 1 kgnot used: no regular price per kilogram recorded; seen 10 Sep 2026
- Bambu Lab Canada: 45 per kg, sale pricePETG-CF - Brick Red (31200) / Filament with spool / 1 kgnot used: no regular price per kilogram recorded; seen 10 Sep 2026
- Bambu Lab Canada: 41 CAD/kgPETG-CF - Black (31100) / Refill / 1 kgin its price; seen 10 Sep 2026
- 3D Printing Canada: 45 per kg, sale priceBlack - Bambu Lab PETG-CF Filament - 1.75mm,1kg / Filament with spoolnot used: no regular price per kilogram recorded; seen 10 Sep 2026
Its 4 documents
What the maker says (5)
- Warping and shrinkage
The specially formulated blend minimizes the risk of warping and nozzle sticking, while still providing a smooth and consistent print quality.
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFp. 1 - Surface finish
Addition of carbon fiber brings distinctive texture and improved strength to the material, making it ideal for high-stress models requiring premium finish.
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFp. 1 - Odour and emissions
Odor Odorless
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFp. 3 - Good for
Thanks to its enhanced resistance to heat and moisture, Bambu PETG-CF is ideal for outdoor applications. Feel free to create durable tools for your garden or any outdoor environment.
Bambu Lab, PETG-CF official maker product pagep. 1: exact product features/description/application tips, source text line 116 - Printing advice
Due to the addition of carbon fiber, PETG-CF requires a more wear-resistant hardened steel nozzle. While a 0.4 mm hardened steel nozzle can be used, a 0.6 mm hardened steel nozzle is recommended to further reduce the risk of clogging.
Bambu Lab, PETG-CF official maker product pagep. 1: exact product features/description/application tips, source text line 140
Specimen preparation (1)
All the specimens were annealed and dried at 65 °C for 8 h before testing
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFTest specimen preparation
Chemicals and environment (7)
- Water solubility: insoluble
Insoluble in water
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFSolubility - Acid resistance: not resistant
Not resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFResistance to Acid - Alkali resistance: not resistant
Not resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFResistance to Alkali - Organic solvent resistance: limited
Not resistant to some organic solvents
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFResistance to Organic Solvent - Oil and grease resistance: limited
Resistant to most kinds of oil and grease
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFResistance to Oil and Grease - Flammability: flammable
Flammable
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFFlammability - Post-processing: described in words
the suggested annealing temperature of models printed with Bambu PETG-CF is 55 to 60 °C, and the time is 65 to 70 hours.
Bambu Lab, Bambu Filament Technical Data Sheet - PETG-CFp. 3: Annealing note
Polymaker Fiberon PETG-rCF08Strength XY, MPa59.8Strength Z, MPa41.1Modulus XY, GPa3.71Charpy notched, kJ/m²4HDT 0.45, °C69HDT 1.8, °C66Price, CAD/kg56Nozzle, °C240–270Bed, °C60–70Chamber, °CnoneDrying, °C, h653 h
Polymaker Fiberon PETG-rCF08Polymaker
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Polymaker, Fiberon PETG-rCF08 Technical Data Sheet20 valuesUnless a row says otherwise: printed specimenmoisture<20% RH during printing/storageprint settingsPrinted at 270 °C nozzle, 60 °C bed, 100% infill, 2 shells, 3 top and bottom layers, cooling fan 0-50%; tensile, flexural and impact specimens to the drawings on the sheet (ASTM D638 / ISO 527, GB/T 1040 and ISO 179, GB/T 1043) (p. 1: how to make specimens) | |||
| Tensile modulus XY | 3710.1 ± 151.1 MPap. 1: Young's modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 2651.9 ± 51.0 MPap. 1: Young's modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 59.8 ± 0.3 MPap. 1: Tensile strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 41.1 ± 4.1 MPap. 1: Tensile strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 5.7 ± 1.0%p. 1: Elongation at break (X-Y) | ISO 527, GB/T 1040 | in the median |
| Elongation at break Z | 1.9 ± 0.3%p. 1: Elongation at break (Z) | ISO 527, GB/T 1040 | in the median |
| Flexural modulus XY | 3779.1 ± 40.6 MPap. 1: Bending modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 1622.2 ± 104.6 MPap. 1: Bending modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 94.6 ± 1.3 MPap. 1: Bending strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 47.8 ± 2.4 MPap. 1: Bending strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 4.0 ± 0.9 kJ/m2p. 1: Charpy impact strength (X-Y) notched | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength XY | 18.0 ± 1.1 kJ/m2p. 1: Charpy impact strength (X-Y) un-notched | ISO 179, GB/T 1043unnotched | not in the median: unnotched |
| HDT at 0.45 MPa | 68.6 °Cp. 1: Heat deflection temp. ISO 75 0.45MPa | ISO 75As the sheet prints it: ISO 75 0.45MPa | in the median |
| HDT at 1.8 MPa | 65.7 °Cp. 1: Heat deflection temp. ISO 75 1.8MPa | ISO 75As the sheet prints it: ISO 75 1.8MPa | in the median |
| Glass transition temperature | 69.7 °Cp. 1: Glass transition temp. | specimen not stated, DSCAs the sheet prints it: DSC, 10°C/min | in the median |
| Vicat softening temperature | 81.6 °Cp. 1: Vicat softening temp. | ISO 306, GB/T 1633 | |
| Density | 1.30 g/cm3p. 1: Density | specimen not stated, ISO 1183, GB/T 1033tested at 23°Cmoisture state not statedprint settings not stated | |
| Water absorption | 0.55 %p. 1: Equilibrium water absorption | specimen not stated, no standard statedmoisture state not statedprint settings not stated | |
| Melt mass-flow rate | 11.5 g/10minp. 1: Melt index | specimen not stated, no standard namedAs the sheet prints it: 230°C, 2.16 kg | |
| Fibre content | PETG-rCF08 %p. 1: Fibre content | specimen not stated, no standard statedmoisture state not statedprint settings not stated | |
Print settings
- Nozzle
- 240–270 °Cown data sheet
- Bed
- 60–70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 65 °C for 3 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 240-270 °C; Bed 60-70 °C; Chamber Room temp.; Drying 65 °C/3HPolymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1: Build plate temperature, Chamber temperature, Drying temp. and time, Nozzle temperature; p. 1: Nozzle note
Price
56 CAD/kgits one regular price in the sample
1 listing
- Voxel Factory: 56 CAD/kgPolymaker Fiberon PETG-rCF08 1.75mm 500g (SKU PMK-FBR-PEG-CF08-500)in its price; seen 30 Sep 2026
Its 2 documents
What the maker says (5)
- Surface finish
It inherits the comprehensive performance of PETG, featuring recycled carbon fiber for enhanced surface texture and improved mechanical properties.
Polymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1 - Moisture sensitivity
Fiberon™ PETG-rCF08 is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1 - Nozzle wear
Normally, the life of a brass nozzle would be approximately 9h.
Polymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1 - Nozzle wear
Abrasion of the brass nozzle happens frequently when printing Fiberon™ PETG-rCF08.
Polymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1 - Nozzle wear
A wear-resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with Fiberon™ PETG-rCF08.
Polymaker, Fiberon PETG-rCF08 Technical Data Sheetp. 1
Eryone PETG-CFStrength XY, MPa48.7Strength Z, MPa24.1Modulus XY, GPa1.77Charpy notched, kJ/m²—HDT 0.45, °C68HDT 1.8, °C—Price, CAD/kg—Nozzle, °C230–250Bed, °C75–80Chamber, °CnoneDrying, °C, h60–656–8 h
Eryone PETG-CFEryone
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Eryone, Technical Data Sheet (TDS) PETG-CF15 values | |||
| Tensile modulus XY | 1768.6 MPap. 2: Elastic modulus X-Y MPa | no standard statedprint settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile modulus Z (X-Z) | 1700.3 MPap. 2: Elastic modulus X-Z MPa | no standard statedprint settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile strength (yield or break not stated) XY | 48.7 MPap. 2: Tensile strength X-Y 50mm/min GB/T 1040.4 MPa | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile strength (yield or break not stated) Z (X-Z) | 24.1 MPap. 2: Tensile strength X-Z 50mm/min GB/T 1843 MPa | GB/T 1843As the sheet prints it: 50mm/min GB/T 1843print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Elongation at break XY | 1.9 %p. 2: Elongation at break X-Y 50mm/min GB/T 1040.4 % | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Elongation at break Z (X-Z) | 1.5 %p. 2: Elongation at break X-Z 50mm/min GB/T 1040.4 % | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Flexural modulus orientation not stated | 3208.9 MPap. 2: Bending modulus 2mm/min GB/T 9341 MPa | GB/T 9341As the sheet prints it: 2mm/min GB/T 9341print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Flexural strength orientation not stated | 63.8 MPap. 2: Bending strength 2mm/min GB/T 9341 MPa | GB/T 9341As the sheet prints it: 2mm/min GB/T 9341print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Impact strength, test unclear | 3 kJ/m2p. 2: Charpy Impact strenght 2.75J GB/T 1843 kJ/m2 | GB/T 1843As the sheet prints it: 2.75J GB/T 1843print settingsprinting temperature=240 ° C, printing speed=80mm/s, base plate 65 ° C, filling=100%, nozzle diameter=0.4mm | listed under other properties |
| HDT at 0.45 MPa | 68 ℃p. 1: Heat distortion temperature(° C) ASTM D648 0.45MPa ℃ | ASTM D648As the sheet prints it: 0.45MPa ASTM D648 | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 68 ℃p. 1: Glass transition temperature (° C) DSC, 10 ° C/min ℃ | DSCAs the sheet prints it: ° C DSC | in the median |
| Vicat softening temperature | 85 ℃p. 1: Vicat Softening Temperature(° C) ASTM D1525 (ISO 306 GB/T 1633) ℃ | ASTM D1525, ISO 306, GB/T 1633 | |
| Density | 1.25 g/cm³p. 1: Density(g/cm³ at 21.5 ° C) ASTM D792 (ISO 1183, GB/T 1033) g/cm³ | ASTM D792, ISO 1183, GB/T 1033As the sheet prints it: g/cm³ at 21.5 ° C) ASTM D792 ISO 1183 GB/T 1033 | |
| Melt mass-flow rate | 19.3 ± 2 g/10minp. 1: Melt Index(g/10 min) 220 ° C, 10kg 240 ° C, 2.16 kg g/10min | no standard namedAs the sheet prints it: g/10 min 220 ° C 10kg 240 ° C 2.16 kg | |
| Fibre content | 15%p. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 230–250 °Cown data sheet
- Bed
- 75–80 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 60–65 °C for 6–8 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 230-250 ℃; Bed 75-80℃; Drying 60-65℃, 6-8hEryone, Technical Data Sheet (TDS) PETG-CFp. 1: Recommended printing settings; p. 1: Sealed printing
Price
Not in the price sample.
Its 2 documents
What the maker says (3)
- Good for
This makes it suitable for a variety of applications, including printing flower pots, fixtures, and water valve switches.
Eryone, Technical Data Sheet (TDS) PETG-CFp. 1 - Benefits
It features excellent transparency and, compared to PLA, exhibits higher toughness and impact resistance, along with good water and weather resistance.
Eryone, Technical Data Sheet (TDS) PETG-CFp. 1 - Benefits
ERYONE PETG-CF filament is an optimized printing material designed to effectively address common issues such as stringing, oozing, nozzle clogging, and jamming, resulting in a smoother printing process.
Eryone, Technical Data Sheet (TDS) PETG-CFp. 1
QIDI PETG CFStrength XY, MPa50Strength Z, MPa28Modulus XY, GPa3.4Charpy notched, kJ/m²8HDT 0.45, °C77HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–270Bed, °C70–80Chamber, °CnoneDrying, °C, h704–6 h
QIDI PETG CFQIDI
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| QIDI, Technical Data Sheet QIDI PETG-CF21 values | |||
| Tensile modulus XY | 3400-3700 MPap. 2: Young's Modulus (MPa) (XY) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed X-Y Axis | in the median |
| Tensile modulus ZX | 1400-1600 MPap. 2: Young's Modulus (MPa) (ZX) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed Z-X Axis | not in the median: measured on a bar in another orientation |
| Tensile strength (yield or break not stated) XY | 50-57 MPap. 2: Tensile Strength (MPa) (XY) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed X-Y Axis | in the median |
| Tensile strength (yield or break not stated) ZX | 26-30 MPap. 2: Tensile Strength (MPa) (ZX) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed Z-X Axis | not in the median: measured on a bar in another orientation |
| Elongation at break XY | 3-7 %p. 2: Elongation at Break (%) (XY) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed X-Y Axis | in the median |
| Elongation at break ZX | 3-6 %p. 2: Elongation at Break (%) (ZX) | ISO 527As the sheet prints it: ISO 527; infill=100 %; column=3D Printed Z-X Axis | not in the median: measured on a bar in another orientation |
| Flexural modulus XY | 3200~3400 MPap. 3: Flexural Modulus (MPa) (3200~3400) | ISO 178As the sheet prints it: ISO 178; infill=100% | in the median |
| Flexural modulus XZ | 3300~3400 MPap. 3: Flexural Modulus (MPa) (3300~3400) | ISO 178As the sheet prints it: ISO 178; infill=100% | not in the median: measured on a bar in another orientation |
| Flexural modulus ZX | 1700~1800 MPap. 3: Flexural Modulus (MPa) (1700~1800) | ISO 178As the sheet prints it: ISO 178; infill=100% | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 84-95 MPap. 3: Flexural Strength (MPa) (84-95) | ISO 178As the sheet prints it: ISO 178; infill=100% | in the median |
| Flexural strength XZ | 95-98 MPap. 3: Flexural Strength (MPa) (95-98) | ISO 178As the sheet prints it: ISO 178; infill=100% | not in the median: measured on a bar in another orientation |
| Flexural strength ZX | 43-54 MPap. 3: Flexural Strength (MPa) (43-54) | ISO 178As the sheet prints it: ISO 178; infill=100% | not in the median: measured on a bar in another orientation |
| Charpy impact strength XY | 20-30 kJ/m²p. 2: Impact Strength (kJ/m²) (20-30) | ISO 179As the sheet prints it: ISO 179; infill=100% | not in the median: unnotched |
| Charpy impact strength XZ | 32-42 kJ/m²p. 2: Impact Strength (kJ/m²) (32-42) | ISO 179As the sheet prints it: ISO 179; infill=100% | not in the median: unnotched |
| Charpy impact strength ZX | 3-13 kJ/m²p. 2: Impact Strength (kJ/m²) (3-13) | ISO 179As the sheet prints it: ISO 179; infill=100% | not in the median: unnotched |
| Charpy impact strength orientation not stated | 8-15 kJ/m²p. 2: Notch Impact Strength (kJ/m²) | ISO 179As the sheet prints it: ISO 179; infill=100 %; column=drawing 2 | in the median |
| HDT at 0.45 MPa | 77 ℃p. 3: Heat Deflection Temperature (HDT) ISO 75 | ISO 75 | in the median |
| Glass transition temperature | 66℃p. 3: GlassTransition Temperature | ISO 11357 | in the median |
| Vicat softening temperature | 83 ℃p. 3: Vicat Softening Temperature (VST) ISO 306 | ISO 306 | |
| Density | 1.27-1.31 g/cm³p. 3: Density ISO 1183 | ISO 1183 | |
| Melt mass-flow rate | 8-14 g/10 minp. 3: Melt Flow Rate (MFR) | ISO 1133 | |
| QIDI, QIDI Filament Guide | Choose the Right Filament3 valuesUnless a row says otherwise: printed bar (its stated orientation says so) | |||
| Tensile strength (yield or break not stated) Z | 28.0MPap. 1: Tensile Strength - Z | no standard stated | in the median |
| Flexural modulus XY | 3300.0MPap. 1: Bending Modulus - XY | no standard stated | not in the median: replaced by a newer edition of the sheet or by the data sheet, so not used in deciding |
| Flexural strength XY | 89.5MPap. 1: Bending Strength - XY | no standard stated | not in the median: replaced by a newer edition of the sheet or by the data sheet, so not used in deciding |
Print settings
- Nozzle
- 240–270 °Cown data sheet
- Bed
- 70–80 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 70 °C for 4–6 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 240-270℃; Bed 70-80℃QIDI, Technical Data Sheet QIDI PETG-CFp. 5: Recommended printing settings; p. 5: Recommended Build Surface
- Nozzle 240-270°C; Drying Required; Blast Drying Oven: 70°C / 4-6 hQIDI, QIDI Filament Guide | Choose the Right Filamentp. 1: Is drying highly recommended?; p. 1: Recommended hardware settings; p. 1: Extruder heat range
Price
Not in the price sample.
1 listing: 1 with no regular price per kilogram recorded
- QIDI Canada: 40 per kg, sale pricePETG-CF / 1 Kg / Black HEX Code #000000 (SKU 042BLK--1-1000)not used: no regular price per kilogram recorded; seen 30 Sep 2026
Its 3 documents
What the maker says (7)
- Benefits
QIDI PETG-CF Filament: Strong, Rigid & Easy to Print
QIDI, Technical Data Sheet QIDI PETG-CFp. 2 - Precision and tolerance
dimensional stability, precise details
QIDI, Technical Data Sheet QIDI PETG-CFp. 2 - Surface finish
a premium matte textured finish.
QIDI, Technical Data Sheet QIDI PETG-CFp. 2 - Odour and emissions
Odor / Low odor
QIDI, Technical Data Sheet QIDI PETG-CFp. 3 - Moisture sensitivity
Blast Drying Oven: 70°C / 4-6 h
QIDI, QIDI Filament Guide | Choose the Right Filamentp. 1 - Nozzle wear
0.4–0.8 mm / Hardened steel nozzle or harder
QIDI, QIDI Filament Guide | Choose the Right Filamentp. 1 - Printing advice
80-90°C / 2-4 h (optional; support parts)
QIDI, QIDI Filament Guide | Choose the Right Filamentp. 1
Extrudr XPETG CFStrength XY, MPa62Strength Z, MPa—Modulus XY, GPa5Charpy notched, kJ/m²5HDT 0.45, °C73HDT 1.8, °C68Price, CAD/kg—Nozzle, °C220–250Bed, °C60–90Chamber, °C—Drying, °C, h606 h
Extrudr XPETG CFExtrudr
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Extrudr, XPETG CF official maker product page19 values | |||
| Tensile modulus orientation not stated | 5000 MPap. 1: Tensile modulus (Young's modulus) | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 62 MPap. 1: Tensile stress at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 3 %p. 1: Elongation at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural modulus orientation not stated | 3800 MPap. 1: Flexural modulus | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 88 MPap. 1: Flexural strength | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength orientation not stated | 5 kJ/m²p. 1: Charpy notched impact strength (+23°C) | ISO 179As the sheet prints it: ISO 179-1eA; notched | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength orientation not stated | 3.5 kJ/m²p. 1: Charpy notched impact strength (-30°C) | ISO 179As the sheet prints it: ISO 179-1eA; notched | not in the median: tested below room temperature |
| Charpy impact strength orientation not stated | 22 kJ/m²p. 1: Charpy unnotched impact strength (+23°C) | ISO 179As the sheet prints it: ISO 179-1eU; unnotched | not in the median: unnotched |
| Charpy impact strength orientation not stated | 16 kJ/m²p. 1: Charpy unnotched impact strength (-30°C) | ISO 179As the sheet prints it: ISO 179-1eU; unnotched | not in the median: unnotched |
| HDT at 0.45 MPa | 73 °Cp. 1: Heat deflection temp. (HDT/B) — 0.45 MPa | ISO 75As the sheet prints it: ISO 75-1; 0.45 MPa | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 1.8 MPa | 68 °Cp. 1: Heat deflection temp. (HDT/A) — 1.8 MPa | ISO 75As the sheet prints it: ISO 75-1; 1.8 MPa | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 80 °Cp. 1: Glass transition temp. (Tg) | ISO 11357As the sheet prints it: ISO 11357-1 (DSC) | in the median |
| Vicat softening temperature | 76 °Cp. 1: Vicat softening temp. (VST/B50) | ISO 306 | |
| Decomposition temperature | 370 °Cp. 1: Thermal decomposition temp. | no standard stated | |
| Density | 1.31 g/cm³p. 1: Density | ISO 1183As the sheet prints it: ISO 1183-1 | |
| Water absorption | < 0.1 %p. 1: Water absorption (saturation, 23°C) | no standard namedAs the sheet prints it: saturation | |
| Melt mass-flow rate | 5 g/10 minp. 1: Melt flow rate (MFR) — 210°C/2.16 kg | ISO 1133As the sheet prints it: ISO 1133-1 (210°C/2.16 kg) | |
| Melt volume-flow rate | 35 cm³/10 minp. 1: Melt volume rate (MVR) — 235°C/5.0 kg | no standard namedAs the sheet prints it: 5.0 kg | |
| Mould shrinkage orientation not stated | 0.2–0.3 %p. 1: Mould shrinkage | ISO 294As the sheet prints it: ISO 294-4 | |
| Extrudr, TECHNICAL DATA SHEET XPETG CF10 valuesThe same values also in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF.Unless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile modulus | 3350 ± 50 MPap. 1: Tensile modulus (E-Modulus) ISO 527 MPaalso in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 527 | not in the median: measured on a moulded bar |
| Tensile strength (yield or break not stated) | 59 ± 0,4 MPap. 1: Strength ISO 527 MPaalso in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 527 | not in the median: measured on a moulded bar |
| Tensile yield strength | 59 ± 0,4 MPap. 1: Yield stress ISO 527 MPaalso in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 527 | not in the median: measured on a moulded bar |
| Elongation at break | 9,4 ± 1,5 %p. 1: Elongation at break ISO 527-2 %also in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 527As the sheet prints it: ISO 527-2 | not in the median: measured on a moulded bar |
| Elongation at yield | 3,8 ± 0,1 %p. 1: Elongation at yield ISO 527 %also in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 527 | listed under other properties |
| Izod impact strength | 1,7 ± 0,4 kj/m²p. 1: Notched impact strength ISO 180 kj/m²also in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 180 | not in the median: measured on a moulded bar |
| Izod impact strength | 67 ± 7 kj/m²p. 1: Unnotched impact strength ISO 180 kj/m²also in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 180 | not in the median: measured on a moulded bar |
| HDT at 0.45 MPa | 69 °Cp. 1: Heat Deflection Temperature HDT/B ISO 75 °Calso in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 75As the sheet prints it: HDT B ISO 75 | not in the median: measured on a moulded bar |
| Vicat softening temperature | 85 °Cp. 1: VICAT A (VST) ISO 306 °Calso in Extrudr, FICHE DE DONNÉES TECHNIQUES XPETG CF | ISO 306 | |
| Density | 1,29 g/cm³p. 1: Density ISO 1183-1XA g/cm³ | specimen not stated, ISO 1183As the sheet prints it: ISO 1183-1XA | |
Print settings
- Nozzle
- 220–250 °Cown data sheet
- Bed
- 60–90 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 60 °C for 6 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 3 print profiles, in the documents' words
- Nozzle 220-250°C; Bed 60-90°CExtrudr, TECHNICAL DATA SHEET XPETG CFp. 1: Recommended printing settings; p. 1: Recommended settings for printers with a 0.4mm Nozzle
- Nozzle 220–250 °C; Bed 60–90 °C; Drying Drying temperature 60 °C; Drying time 4–6 hExtrudr, XPETG CF official maker product pagep. 1: Exact product drying table and own nozzle recommendation; other recipe fields not transcribed in this scoped profile; p. 1: Nozzle temperature; p. 1: Build plate temperature; p. 1: Surface preparation; p. 1: Enclosed chamber required; p. 1: Hardened nozzle required
- Nozzle 220-250°C; Bed 60-90°CExtrudr, FICHE DE DONNÉES TECHNIQUES XPETG CFp. 1: Buse; p. 1: Plateau chauffant; p. 1: Paramètres recommandés pour les imprimantes avec une buse de 0,4 mm
Price
Not in the price sample.
Its 4 documents
What the maker says (6)
- Warping and shrinkage
Low warping
Extrudr, TECHNICAL DATA SHEET XPETG CFp. 1 - Warping and shrinkage
Low shrinking
Extrudr, TECHNICAL DATA SHEET XPETG CFp. 1 - Nozzle wear
Hardened Nozzle yes
Extrudr, TECHNICAL DATA SHEET XPETG CFp. 1 - Benefits
XPETG CF offers greater tensile strength and heat resistance than standard PETG, thanks to carbon fiber reinforcement, making it well-suited to rigid, load-bearing parts. This added stiffness comes with a trade-off in impact resistance compared to standard PETG, so XPETG CF is best suited to applications where rigidity matters more than shock resistance.
Extrudr, XPETG CF official maker product pagep.1: Exact product FAQ/highlight, source text line107 - Pitfalls and limitations
XPETG CF offers good resistance to UV, moisture, and heat, making it generally suitable for outdoor use. However, prolonged, permanent outdoor exposure can still cause gradual fading or embrittlement over time.
Extrudr, XPETG CF official maker product pagep.1: Exact product FAQ/highlight, source text line109 - Pitfalls and limitations
No. Carbon fiber reinforced filaments, including XPETG CF, are not certified for food contact. Any application requiring food safety should use a non-reinforced filament with confirmed food-contact compliance, such as PETG.
Extrudr, XPETG CF official maker product pagep.1: Exact product FAQ/highlight, source text line112
Raise3D Hyper Speed PETG CFStrength XY, MPa60Strength Z, MPa—Modulus XY, GPa3.7Charpy notched, kJ/m²4HDT 0.45, °C69HDT 1.8, °C65Price, CAD/kg—Nozzle, °C240–270Bed, °C60–80Chamber, °CnoneDrying, °C, h658 h
Raise3D Hyper Speed PETG CFRaise3D
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheet18 valuesUnless a row says otherwise: printed specimenprint settingsNozzle temp. =270 ºC; Bed temp.= 60 ºC; Infill= 100% | |||
| Tensile modulus XY | 3700± 150 MPap. 1: Young’s modulus (MPa) (3700± 150) | ISO 527 | in the median |
| Tensile modulus ZX | 2600 ± 50.0 MPap. 1: Young’s modulus (MPa) (2600 ± 50.0) | ISO 527 | not in the median: measured on a bar in another orientation |
| Tensile strength (yield or break not stated) XY | 60 ± 0.3 MPap. 1: Tensile strength (MPa) (60 ± 0.3) | ISO 527 | in the median |
| Tensile strength (yield or break not stated) ZX | 40 ± 4.1 MPap. 1: Tensile strength (MPa) (40 ± 4.1) | ISO 527 | not in the median: measured on a bar in another orientation |
| Elongation at break XY | 6.0 ± 1.0 %p. 1: Elongation at break (%) (6.0 ± 1.0) | ISO 527 | in the median |
| Elongation at break ZX | 2.0 ± 0.3 %p. 1: Elongation at break (%) (2.0 ± 0.3) | ISO 527 | not in the median: measured on a bar in another orientation |
| Flexural modulus XY | 3800 ± 40.6 MPap. 1: Bending modulus (MPa) (3800 ± 40.6) | ISO 178 | in the median |
| Flexural modulus ZX | 1700 ± 104.6 MPap. 1: Bending modulus (MPa) (1700 ± 104.6) | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 95 ± 1.3 MPap. 1: Bending strength (MPa) (95 ± 1.3) | ISO 178 | in the median |
| Flexural strength ZX | 48 ± 2.4 MPap. 1: Bending strength (MPa) (48 ± 2.4) | ISO 178 | not in the median: measured on a bar in another orientation |
| Charpy impact strength XY | 18.0 ± 1.1 (Un-notched) kJ/m²p. 1: Charpy impact strength (kJ/m²) (Un-notched) | ISO 179unnotched | not in the median: unnotched |
| Charpy impact strength XY | 4.0 ± 0.9 (Notched) kJ/m²p. 1: Charpy impact strength (kJ/m²) (Notched) | ISO 179 | in the median |
| HDT at 0.45 MPa | 69 °Cp. 2: Heat distortion temperature (°C) (69) | ISO 75As the sheet prints it: ISO 75; 0.45 MPa | in the median |
| HDT at 1.8 MPa | 65 °Cp. 2: Heat distortion temperature (°C) (65) | ISO 75As the sheet prints it: ISO 75; 1.8 MPa | in the median |
| Density | 1.30 g/cm³p. 1: Density | specimen not stated, ISO 1183, GB/T 1033print settings not stated | |
| Water absorption | 0.55 %p. 1: Water absorption | specimen not stated, no standard statedprint settings not stated | |
| Melt mass-flow rate | 12 g/10 minp. 2: Melt flow index (g/10 min) | specimen not stated, no standard namedAs the sheet prints it: 2.16 kg | |
| Fibre content | 8 wt.%p. 1: Fibre content | specimen not stated, no standard statedprint settings not stated | |
Print settings
- Nozzle
- 240–270 °CBambu Lab Filament Guide
- Bed
- 60–80 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- No temperature statedRaise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 2: the conditions the test specimens were printed under, which are not printing guidance; p. 2: Note 1. Its nozzle and bed temperatures are the specimens' print conditions, which are not printing guidance.
Price
Not in the price sample.
Its 2 documents
What the maker says (6)
- Benefits
Raise3D Hyper Speed PETG CF is a carbon fiber reinforced (8 wt.% recycled CF) Polyethylene Terephthalate Glycol modified (PETG) filament optimized for Hyper FFF® technology (up to L2, 300 mm/s).
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 1 - Benefits
Hyper speed PETG CF retains not only the excellent overall printing performance of PETG, but also exhibits enhanced matt carbon-fiber texture and improved mechanical, thermal properties, and dimensional stability through the incorporation of recycled carbon fibers.
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 1 - Odour and emissions
Odor / Almost odorless
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 1 - Moisture sensitivity
Hyper Speed PETG CF is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 2 - Nozzle wear
Normally, the life of a brass nozzle would be approximately 9h.
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 2 - Nozzle wear
A wear-resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with Hyper Speed PETG CF.
Raise3D, Raise3D Hyper Speed PETG CF Technical Data Sheetp. 2
Siraya Tech Fibreheart PETG CF ProStrength XY, MPa44Strength Z, MPa—Modulus XY, GPa3.4Charpy notched, kJ/m²—HDT 0.45, °C75HDT 1.8, °C69Price, CAD/kg—Nozzle, °C250–270Bed, °C70–80Chamber, °CnoneDrying, °C, h70–804–6 h
Siraya Tech Fibreheart PETG CF ProSiraya Tech
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Tech13 values | |||
| Tensile modulus XY | 3400 MPap. 1: Young’s Modulus X-Y (MPa) | ASTM D638 | in the median |
| Tensile break strength XY | 44 MPap. 1: Tensile Stress at Break X-Y (MPa) | ASTM D638 | in the median |
| Elongation at break XY | 7.5 %p. 1: Elongation at Break X-Y (%) | ASTM D638 | in the median |
| Flexural modulus orientation not stated | 3450 MPap. 1: Bending Modulus (MPa) | ISO 178 | in the median |
| Flexural strength orientation not stated | 85 MPap. 1: Bending Strength (MPa) | ISO 178 | in the median |
| Izod impact strength orientation not stated | 15 J/mp. 1: IZOD Impact (Notched 72F) (J/m) | ASTM D256tested at 72 °F | not in the median: in J/m |
| HDT at 0.45 MPa | 75 ℃p. 1: HDT @ 0.45 MPa (℃) | no standard namedAs the sheet prints it: Method B; 0.45 MPa | in the median |
| HDT at 1.8 MPa | 69 ℃p. 1: HDT @ 1.80 MPa (℃) | no standard namedAs the sheet prints it: Method A; 1.80 MPa | in the median |
| Glass transition temperature | 68 ℃p. 1: Glass Transition Temperature (℃) | ASTM D3418 | in the median |
| Vicat softening temperature | 85 ℃p. 1: Vicat softening temperature (℃) | ISO 306 | |
| Melting temperature | 220 ℃p. 1: Melting Point (℃) | ASTM D3418 | |
| Density | 1.3 g/cm³p. 1: Filament Density g/cm³ | no standard stated | |
| Fibre content | 10% short cut carbon fiberp. 1: Material | no standard stated | |
Print settings
- Nozzle
- 250–270 °Cown data sheet
- Bed
- 70–80 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 70–80 °C for 4–6 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 250-270 ℃; Bed 70-80°C; Drying 70-80°C for 4-6 hoursSiraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Techp. 1: Recommended printing settings; p. 1: Drying; p. 1: Enclosure; p. 1: Recommended Nozzle Diameter
Price
Not in the price sample.
Its 2 documents
What the maker says (4)
- Moisture sensitivity
Moisture causes steam bubbles. Dry the filament.
Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Techp. 1 - Nozzle wear
Nozzle material Carbon hardened, hardened steel or higher grade nozzles
Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Techp. 1 - Printing advice
Enclosure Not mandatory, but it is recommended
Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Techp. 1 - Printing advice
Avoid " squishing" th e first laye r too t ight ly, as this can ca us e nozzl e clog s
Siraya Tech, Fibreheart PETG-CF Pro TDS | Enhanced Carbon Fiber Filament | Siraya Techp. 1
3DXTECH CarbonX Carbon Fiber PETGStrength XY, MPa56Strength Z, MPa—Modulus XY, GPa5.23Charpy notched, kJ/m²—HDT 0.45, °C77HDT 1.8, °C—Price, CAD/kg—Nozzle, °C230–260Bed, °C70–90Chamber, °CnoneDrying, °C, h654 h
3DXTECH CarbonX Carbon Fiber PETG3DXTECH
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
3DXTECH, Technical Data Sheet: CarbonX™ Carbon Fiber PETG 3D Printing Filament8 valuesUnless a row says otherwise: printed specimenprint settingsPrinted Specimen Conditions Printer: Open Source FDM/FFF Nozzle: 0.4mm Layer Height: 0.25mm Infill: 100%, +/- 45° Extrusion Temp: 245°C Bed Temp: 60°C Specimen Orientation: XY Flat | |||
| Tensile modulus XY | 5230 MPap. 1: Tensile Modulus ISO 527 MPa | ISO 527 | in the median |
| Tensile break strength XY | 56 MPap. 1: Tensile Strength, Break ISO 527 MPa | ISO 527 | in the median |
| Elongation at break XY | 3 %p. 1: Tensile Elongation, Break ISO 527 % | ISO 527 | in the median |
| Flexural modulus XY | 5740 MPap. 1: Flexural Modulus ISO 178 MPa | ISO 178 | in the median |
| Flexural strength XY | 80 MPap. 1: Flexural Strength ISO 178 MPa | ISO 178 | in the median |
| HDT at 0.45 MPa | 77 °Cp. 1: Deflection Temperature at 0.45 ISO 75 °C | ISO 75As the sheet prints it: ISO 75, 0.45 MPa (66psi) | in the median |
| Glass transition temperature | 80 °Cp. 1: Glass Transition Temperature (Tg) DSC °C | DSCAs the sheet prints it: Tg DSC °C | in the median |
| Density | 1.34 g/ccp. 1: Density ISO 1183 g/cc | ISO 1183As the sheet prints it: 1183 g/cc ISO 1183 | |
| 3DXTECH, CarbonX Carbon Fiber PETG safety data sheet1 value | |||
| Fibre content | <20 %p. 1: Carbon Fiber | no standard stated | |
Print settings
- Nozzle
- 230–260 °Cown data sheet
- Bed
- 70–90 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 65 °C for 4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 2 print profiles, in the documents' words
- No temperature stated3DXTECH, Technical Data Sheet: CarbonX™ Carbon Fiber PETG 3D Printing Filamentp. 1: Printed Specimen Conditions, which are not printing guidance
- Nozzle 230-260C; Bed 70-90C; Chamber Not Required; Drying 65C for 4 hours3DXTECH, CARBONX™ PETG+CFp. 1: Extruder Temp; p. 1: Tips from Our Engineers; p. 1: Bed Temp; p. 1: Heated Chamber; p. 1: Nozzle Specs; p. 1: Drying Specs
Price
Not in the price sample.
Its 4 documents
What the maker says (1)
- Warping and shrinkage
Amorphous structure giving it low, near isotropic shrinkage
3DXTECH, CARBONX™ PETG+CFp. 1
SUNLU PETG Carbon FiberStrength XY, MPa32Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²7IzodHDT 0.45, °C71HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–250Bed, °C50–70Chamber, °CnoneDrying, °C, h70
SUNLU PETG Carbon FiberSUNLU
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiber12 valuesUnless a row says otherwise: printed specimen | |||
| Tensile strength (yield or break not stated) XY | 32 ± 4 MPap. 1: (X-Y) Tensile Strength ISO 527/2 50 mm/min MPa | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | in the median |
| Elongation at break XY | 14 ± 3 %p. 1: (X-Y) Elongation at break ISO 527/2 50 mm/min % | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural modulus XY | 1960 ± 200 MPap. 1: (X-Y) Flexural Modulus ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural strength XY | 55.5 ± 5 MPap. 1: (X-Y) Flexural Strength ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength XY | 7 ± 2 KJ/m2p. 1: (X-Y) Izod Impact Strength of Notched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength ZX | 5.5 ± 1.5 KJ/m2p. 1: (Z-X) Izod Impact Strength of Unnotched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 45 mm/s; Printing temperature 255 °C; Infill: 100%; 90° raster orientation | not in the median: unnotched |
| Hardness | 71 Shore (scale not specified by source)p. 1: Shore Hardness ISO 868 23℃ HA/HD | ISO 868As the sheet prints it: 23℃ HA/HD ISO 868 | listed under other properties |
| HDT XY, at 0.45 MPa | 71 ± 3 ℃p. 1: (X-Y) Heat Distortion (HDT) ISO 75 0.45 MPa ℃ | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | in the median |
| Glass transition temperature | 65 ℃p. 1: Glass Transition (Tg) ISO 11357-2 10 ℃/min ℃ | ISO 11357As the sheet prints it: ISO 11357-2 | in the median |
| Decomposition temperature | ≥425 ℃p. 1: @5%Decomposition Temp. | ISO 11358As the sheet prints it: ISO 11358; rate=20 ℃/min; loss=5% | |
| Density | 1.23 g/cm3p. 1: Density ISO 1183 23℃ g/cm3 | specimen not stated, ISO 1183As the sheet prints it: 23℃ ISO 1183 | |
| Melt mass-flow rate | 5.7 ± 1.5 g/10 minp. 1: Melt Mass-flow Rate ISO 1133 210℃/2.16 kg g/10 min | ISO 1133As the sheet prints it: 210℃/2.16 kg ISO 1133 | |
| SUNLU, SUNLU PETG Carbon Fiber safety data sheet1 value | |||
| Fibre content | 10 %p. 2: Carbon fiber | no standard stated | |
Print settings
- Nozzle
- 240–250 °Cown data sheet
- Bed
- 50–70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 70 °Cown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 240-250; Bed 50-70℃; Chamber Room Temperature; Drying 70℃SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 2: Recommended printing settings; p. 2: Nozzle Temp.
Price
Not in the price sample.
Its 3 documents
What the maker says (5)
- Good for
Structural parts, decorative items, toys, accessories, and figurines.
SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 1 - Benefits
excellent impact resistance.
SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 1 - Surface finish
Printed models exhibit a carbon fiber texture
SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 1 - Moisture sensitivity
To achieve better print quality, if the filament has been exposed to air for more than 48 hours after opening the package, it is recommended to perform moisture drying before printing.
SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 1 - Supports and removal
Supported Material PVA
SUNLU, TECHNICAL DATA SHEET ISO PETG Carbon Fiberp. 2
3DJake easyPETG CFStrength XY, MPa72Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²4IzodHDT 0.45, °C74HDT 1.8, °C68Price, CAD/kg—Nozzle, °C220–250Bed, °C60–90Chamber, °CnoneDrying, °C, h658 h
3DJake easyPETG CF3DJake
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| 3DJake, Technical Data Sheet 3DJAKE easyPETG CF15 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile strength (yield or break not stated) orientation not stated | 72 MPap. 1: Tensile strength | ISO 527As the sheet prints it: ISO 527-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile yield strength orientation not stated | 70 MPap. 1: Tensile yield stress | ISO 527As the sheet prints it: ISO 527-2 | not in the median: another value of this product is in it |
| Tensile break strength orientation not stated | 65 MPap. 1: Stress at break | ISO 527As the sheet prints it: ISO 527-2 | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 9 %p. 1: Nominal strain at break | ISO 527As the sheet prints it: ISO 527-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at yield orientation not stated | 3 %p. 1: Strain at yield | ISO 527As the sheet prints it: ISO 527-2 | listed under other properties |
| Flexural modulus orientation not stated | 2860 MPap. 1: Flexural modulus | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 85 MPap. 1: Flexural strength | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength | 4 kJ/m²p. 1: Notched impact strength (Izod, 23 °C) | ISO 180As the sheet prints it: Izod 23 °C ISO 180 | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength | 4 kJ/m²p. 1: Notched impact strength (Izod, 0 °C) | ISO 180As the sheet prints it: Izod 0 °C ISO 180 | not in the median: tested below room temperature |
| Izod impact strength orientation not stated | 3 kJ/m²p. 1: Notched impact strength (Izod, -30 °C) | ISO 180tested at -30 °C | not in the median: tested below room temperature |
| Izod impact strength orientation not stated | 85 kJ/m²p. 1: Unnotched impact strength (Izod, -30 °C) | ISO 180tested at -30 °C | not in the median: unnotched |
| HDT at 0.45 MPa | 74 °Cp. 1: HDT (0,45 MPa) | ISO 75As the sheet prints it: 0,45 MPa ISO 75-2 | in the median |
| HDT at 1.8 MPa | 68 °Cp. 1: HDT (1,80 MPa) | ISO 75As the sheet prints it: 1,80 MPa ISO 75-2 | in the median |
| Vicat softening temperature | 85 °Cp. 1: Vicat VST B50 | ISO 306As the sheet prints it: 50 ISO 306 | |
| Density | 1,31 g/cm³p. 1: Density | ASTM D792 | |
| 3DJake, 3DJake easyPETG CF Filaments1 value | |||
| Fibre content | 10% carbon fibrep. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 220–250 °Cown data sheet
- Bed
- 60–90 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 220 – 250 °C; Bed 60 – 90 °C3DJake, Technical Data Sheet 3DJAKE easyPETG CFp. 1: Recommended printing settings; p. 1: Heated bed
Price
Not in the price sample.
Its 3 documents
What the maker says (3)
- Benefits
easyPETG + 10% carbon fibre High dimensional stability High chemical resistance
3DJake, 3DJake easyPETG CF Filamentsp. 1 - Warping and shrinkage
High dimensional stability
3DJake, 3DJake easyPETG CF Filamentsp. 1 - Benefits
High chemical resistance
3DJake, 3DJake easyPETG CF Filamentsp. 1
3D4Makers PETGCarbonStrength XY, MPa52.9Strength Z, MPa—Modulus XY, GPa4.01Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C220–260Bed, °C60–100Chamber, °CnoneDrying, °C, h652–4 h
3D4Makers PETGCarbon3D4Makers
Sold as toughened or impact-modified: "Increased Impact Resistance compared to regular PETG" (3D4Makers, PETG Carbon Filament, p. 1). The maker's statement, not a test result.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| 3D4Makers, PETG Carbon Filament6 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile modulus orientation not stated | 4,015 MPap. 1: Tensile Modulus | printed specimen (implied by the document), no standard stated | in the median |
| Tensile strain at strength orientation not stated | 2.4%p. 1: Elongation at tensile strength | no standard stated | listed under other properties |
| Flexural modulus orientation not stated | 2,987 MPap. 1: Flexural Modulus | printed specimen (implied by the document), no standard stated | in the median |
| Charpy impact strength orientation not stated | 4.03 KJ/m2p. 1: Charpy impact Strength | no standard stated | not in the median: notch not stated |
| Hardness | 76.4 Shore Dp. 1: Shore D Hardness | no standard stated | in the median |
| Glass transition temperature | 76 °Cp. 1: Glass temperature tg | no standard stated | in the median |
| 3D4Makers, Technical Data Sheet 3D Printing Filament PETG Carbon Filament4 valuesUnless a row says otherwise: printed specimen | |||
| Tensile strength (yield or break not stated) orientation not stated | 52.9 MPap. 1: Tensile Strength | ISO 527As the sheet prints it: ISO 527-2/5A/50 | in the median |
| Tensile break strength orientation not stated | 41.3 MPap. 1: Tensile Stress at Break | ISO 527As the sheet prints it: ISO 527-2/5A/50 | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 3.4 %p. 1: Tensile strain at break | ISO 527As the sheet prints it: ISO 527-2/5A/50 | in the median |
| Density | 1.317 g/cm³p. 1: Density | specimen not stated, ISO 1183As the sheet prints it: ISO1183-1 | |
Print settings
- Nozzle
- 220–260 °Cown data sheet
- Bed
- 60–100 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 65 °C for 2–4 hown data sheet
- Hardened nozzle
- neededown data sheet
Differs in another document of this product, not used in deciding (a data sheet speaks before a product page, a newer edition before an older one): nozzle in 3D4Makers, PETG Carbon Filament; bed in 3D4Makers, PETG Carbon Filament.
Its 2 print profiles, in the documents' words
- Nozzle 220-260°C; Bed 60-100°C; Drying 2-4hours,65°C3D4Makers, Technical Data Sheet 3D Printing Filament PETG Carbon Filamentp. 1: Recommended printing settings: NozzleTemperature; p. 1: Dryingrecommendations
- Nozzle 250°C (240-280 °C); Bed 70°C (60-80 °C)3D4Makers, PETG Carbon Filamentp. 1: Abrasive; p. 1: Print Temperature; p. 1: Bed Temperature
Price
Not in the price sample.
Its 3 documents
What the maker says (8)
- Nozzle wear
We advise to use a hardened steel nozzle.
3D4Makers, PETG Carbon Filamentp. 1 - Benefits
Increased Impact Resistance compared to regular PETG
3D4Makers, PETG Carbon Filamentp. 1 - Benefits
Due to the carbon fibers compounded in the PETG you can create 3D printed parts with exceptional stiffness, great dimensional stability and excellent suface quality.
3D4Makers, PETG Carbon Filamentp. 1 - Good for
This filament is highly suitable for printing a wide range of industrial applications like frames, drones, tools, parts for the automotive and more.
3D4Makers, PETG Carbon Filamentp. 1 - Nozzle wear
Abrasive please be aware of the wear of carbon filled filaments.
3D4Makers, PETG Carbon Filamentp. 1 - Benefits
Easy to Print.
3D4Makers, PETG Carbon Filamentp. 1 - Warping and shrinkage
Great Dimensional Stability.
3D4Makers, PETG Carbon Filamentp. 1 - Benefits
Extremely Stiff.
3D4Makers, PETG Carbon Filamentp. 1
Flashforge PETGCF10Strength XY, MPa40Strength Z, MPa—Modulus XY, GPa2.1Charpy notched, kJ/m²3IzodHDT 0.45, °C70HDT 1.8, °C—Price, CAD/kg—Nozzle, °C230–250Bed, °C50–80Chamber, °C25–65Drying, °C, h70≥ 5 h
Flashforge PETGCF10Flashforge
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Flashforge, Technical Data Sheet PETGCF10 Filament11 values | |||
| Tensile modulus XY | 2100-2400 Mpap. 1: Modulus of Elasticity (X-Y) ISO 527 Mpa | ISO 527as printedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 50mm/s; Wall Thickness 1.2mm; Infill 100%; Note: The above test parameter data are obtained from actual printing, and the printed model has not been annealed. | in the median |
| Tensile strength (yield or break not stated) XY | 40-43 Mpap. 1: Tensile Strength (X-Y) ISO 527 Mpa | ISO 527as printedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 50mm/s; Wall Thickness 1.2mm; Infill 100%; Note: The above test parameter data are obtained from actual printing, and the printed model has not been annealed. | in the median |
| Elongation at break XY | 7.5-8.5 %p. 1: Elongation at Break (X-Y) ISO 527 % | ISO 527as printedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 50mm/s; Wall Thickness 1.2mm; Infill 100%; Note: The above test parameter data are obtained from actual printing, and the printed model has not been annealed. | in the median |
| Flexural strength XY | 75-85 Mpap. 1: Bending Strength (X-Y) ISO 178 Mpa | ISO 178as printedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 50mm/s; Wall Thickness 1.2mm; Infill 100%; Note: The above test parameter data are obtained from actual printing, and the printed model has not been annealed. | in the median |
| Izod impact strength XY | 3-3.5 KJ/m2p. 1: Izod Impact Strength (X-Y) ISO 180 KJ/m2 | ISO 180as printednotchedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 50mm/s; Wall Thickness 1.2mm; Infill 100%; Note: The above test parameter data are obtained from actual printing, and the printed model has not been annealed. | in the median |
| HDT at 0.45 MPa | 70 ℃p. 1: HDT@ 0.455 MPa (66 psi) ISO 75 ℃ | ISO 75As the sheet prints it: 0.455 MPa 66 psi ISO 75 | in the median |
| Continuous service temperature | 80 ℃p. 1: Continuous Service Temperature IEC 60216 ℃ | IEC 60216 | |
| Density | 1.27-1.28 g/cm3p. 1: Density ISO 1183 g/cm3 | ISO 1183 | |
| Water absorption | 0.8 %p. 1: Water Absorption (23℃/24h) ISO 62 % | ISO 62As the sheet prints it: 23℃/24h ISO 62 | |
| Melt mass-flow rate | 10-15 g/10minp. 1: Melt Index MFR (220℃/2.16Kg) ISO 1133 g/10min | ISO 1133As the sheet prints it: 220℃/2.16Kg ISO 1133 | |
| Fibre content | 10% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 230–250 °Cown data sheet
- Bed
- 50–80 °Cown data sheet
- Heated chamber
- 25–65 °Cown data sheet
- Drying
- 70 °C for ≥ 5 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 230~250℃ (240℃ recommended); Bed 50~80℃ (70℃ recommended); Chamber Room temperature~65℃; Drying Using a hot dry air oven at 70℃ for at least 5 hours is recommendedFlashforge, Technical Data Sheet PETGCF10 Filamentp. 2: Recommended printing settings: Nozzle Temperature; p. 2: Ambient Temperature for Printing; p. 3: Drying note; p. 2: Nozzle Diameter (recommended printing settings)
Price
Not in the price sample.
Its 2 documents
What the maker says (5)
- Benefits
PETGCF10 has excellent dimensional stability and rigidity and is easier to print than PETG filament.
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 1 - Benefits
Dimensional stability/High strength/Easy-to-print property.
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 1 - Supports and removal
Recommended Support Material Self-supporting
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 2 - Moisture sensitivity
Because of the addition of carbon fiber, PETGCF10 filament absorbs moisture more easily than PETG filament, so it should be dried before being used.
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 3 - Printing advice
After the printing process, it is recommended to dry the model in an oven at 70°C for 1-3 hours in order to increase the strength of the model.
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 3
Chemicals and environment (1)
- Post-processing: described in words
After the printing process, it is recommended to dry the model in an oven at 70°C for 1-3 hours in order to increase the strength of the model.
Flashforge, Technical Data Sheet PETGCF10 Filamentp. 3: Post-processing note
Fiberlogy PETG+CFStrength XY, MPa105Strength Z, MPa—Modulus XY, GPa9Charpy notched, kJ/m²6.5HDT 0.45, °C72HDT 1.8, °C69Price, CAD/kg—Nozzle, °C230–260Bed, °C90Chamber, °CnoneDrying, °C, h604 h
Fiberlogy PETG+CFFiberlogy
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Fiberlogy, TECHNICAL DATA SHEET Fiberlogy PETG+CF8 valuesUnless a row says otherwise: specimen not stated; its document points to a moulded or resin bar | |||
| Tensile modulus orientation not stated | 9000 MPap. 1: Tensile Modulus ISO 527 MPa | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 105 MPap. 1: Tensile Strength @ Break ISO 527 MPa | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 4 %p. 1: Elongation @ Break ISO 527 % | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength | 45 kJ/m2p. 1: Charpy Impact Strength (Unnotched) @ 23°C ISO 179 kJ/m2 | ISO 179As the sheet prints it: 23°C ISO 179 | not in the median: unnotched |
| Charpy impact strength | 6.5 kJ/m2p. 1: Charpy Impact Strength (Notched) @ 23°C ISO 179 kJ/m2 | ISO 179As the sheet prints it: 23°C ISO 179 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 0.45 MPa | 72 °Cp. 1: Heat Distortion Temperature @ 0.45 MPa ISO 75 °C | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 1.8 MPa | 69 °Cp. 1: Heat Distortion Temperature @ 1.8 MPa ISO 75 °C | ISO 75As the sheet prints it: 1.8 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| Vicat softening temperature | 77 °Cp. 1: Vicat Softening Temperature ISO 306 °C | specimen not stated, ISO 306 | |
| Fiberlogy, PETG+CF Filament4 valuesUnless a row says otherwise: specimen not stated | |||
| Charpy impact strength orientation not stated | 6.5 kJ/m²p. 1: Charpy impact strength (notched) @ 23°C | ISO 179tested at 23 °C | not in the median: another value of this product is in it |
| Charpy impact strength orientation not stated | 45 kJ/m²p. 1: Charpy impact strength (unnotched) @ 23°C | ISO 179tested at 23 °C | not in the median: unnotched |
| Density | 1.32 g/cm³p. 1: Density | no standard stated | |
| Fibre content | 10% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 230–260 °Cown data sheet
- Bed
- 90 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 60 °C for 4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 230°C - 260°C; Bed 90°CFiberlogy, TECHNICAL DATA SHEET Fiberlogy PETG+CFp. 1: Recommended printing settings
- Nozzle 230–260°C; Bed 90°C; Drying 60°C / 4 hoursFiberlogy, PETG+CF Filamentp. 1: Description; p. 1: Description; p. 1: Printing temperature; p. 1: Bed temperature; p. 1: Bed material; p. 1: Drying conditions
Price
Not in the price sample.
Its 3 documents
What the maker says (1)
- Benefits
combines the versatility and printability of PET-G with the strength and stiffness provided by 10% carbon fiber
Fiberlogy, PETG+CF Filamentp. 1
SIDDAMENT PETG Carbon FiberStrength XY, MPa35Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²20IzodHDT 0.45, °C70HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–260Bed, °C70Chamber, °CnoneDrying, °C, h602–4 h
SIDDAMENT PETG Carbon FiberSIDDAMENT
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SIDDAMENT, PETG Carbon Fiber - Technical Datasheet8 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile strength (yield or break not stated) orientation not stated | 35 MPap. 1: Tensile Strength ISO 527 MPa | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 30 %p. 1: Elongation at Break ISO 527 % | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural modulus orientation not stated | 2700 MPap. 1: Flexural Modulus ISO 178 MPa | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 55 MPap. 1: Bending Strength ISO 178 MPa | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength | 20 kJ/m2p. 1: Notched Impact Strength ISO 180 kJ/m2 | ISO 180 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT | 70 °Cp. 1: Heat Deflection ISO 75 °C | ISO 75 | not in the median: set apart (never used to pass), no stated test load |
| Density | 1.22 g/cm3p. 1: Density ISO 1183 g/cm3 | ISO 1183 | |
| Water absorption | 0.35 %p. 1: Water Absorption ISO 62 % | ISO 62 | |
Print settings
- Nozzle
- 240–260 °Cown data sheet
- Bed
- 70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- optional: 60 °C for 2–4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 240-260°C; Bed 70°C; Drying If damp, dry at 60°C for 2-4 hours.SIDDAMENT, PETG Carbon Fiber - Technical Datasheetp. 1: Drying note; p. 2: Nozzle Temperature; p. 2: Bed Temperature; p. 2: Nozzle Diameter; p. 2: Printing Platform
Price
Not in the price sample.
Its 2 documents
What the maker says (2)
- Nozzle wear
Hardened Nozzle Recommended
SIDDAMENT, PETG Carbon Fiber - Technical Datasheetp. 2 - Supports and removal
Supporting Material: Self-supporting, PVA
SIDDAMENT, PETG Carbon Fiber - Technical Datasheetp. 2
Recreus PET-G CFStrength XY, MPa105Strength Z, MPa—Modulus XY, GPa9Charpy notched, kJ/m²6.5HDT 0.45, °C72HDT 1.8, °C69Price, CAD/kg—Nozzle, °C245–260Bed, °C70Chamber, °CnoneDrying, °C, h658 h
Recreus PET-G CFRecreus
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Recreus, TECHNICAL DATA SHEET PET-G CF8 valuesThe same values also in Recreus, TECHNICAL DATA SHEET PET-G CF.Unless a row says otherwise: specimen not stated | |||
| Tensile modulus orientation not stated | 9000 MPap. 1: Tensile modulus (Young) | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile strength (yield or break not stated) orientation not stated | 105 MPap. 1: Tensile strength | DIN 53504As the sheet prints it: DIN 53504-S2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 4% %p. 1: Elongation at break | DIN 53504As the sheet prints it: DIN 53504-S2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength orientation not stated | 6,5 kJ/m2p. 1: Notched impact strengh (Charpy)n at +23°C | ISO 179tested at 23 °C | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 0.45 MPa | 72 °Cp. 1: HDT (0,45MPa)also in Recreus, TECHNICAL DATA SHEET PET-G CF | ISO 75As the sheet prints it: 0,45MPa ISO 75-2 | in the median |
| HDT at 1.8 MPa | 69 °Cp. 1: HDT (01,82MPa) | ISO 75As the sheet prints it: 01,82MPa ISO 75-2 | in the median |
| Vicat softening temperature | 77 °Cp. 1: VST Vicat Softening Temperature | no standard namedAs the sheet prints it: Método Vicat A: 50 Nw, 50°C/h; method=Vicat A; rate=50 °C/h | |
| Density | 1,1 g/cm3physically implausiblep. 1: Material density | ISO 1183 | |
| Recreus, TECHNICAL DATA SHEET PET-G CF2 valuesUnless a row says otherwise: specimen not stated | |||
| HDT at 1.8 MPa | 67,0 °Cp. 1: HDT (01,82MPa} | ISO 75As the sheet prints it: 01,82MPa ISO 75-2 | not in the median: another value of this product is in it |
| Vicat softening temperature | 80,0 °Cp. 1: VST Vicat Softening Temperature | no standard namedAs the sheet prints it: Vicat A Method: 50 Nw, 50°C/h; method=Vicat A; rate=50 °C/h | |
Print settings
- Nozzle
- 245–260 °Cown data sheet
- Bed
- 70 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 245-260°C; Bed 70°CRecreus, TECHNICAL DATA SHEET PET-G CFp. 1: Printing temperatures; p. 1: Hot-bed temperature
Price
Not in the price sample.
Its 3 documents
What the maker says (2)
- Benefits
Its main characteristic is its mechanical strength which is 5 times higher than its original formulation.
Recreus, TECHNICAL DATA SHEET PET-G CFp. 1 - Nozzle wear
Hardened steel or ruby-type (avoid brass) of 0.50 mm
Recreus, TECHNICAL DATA SHEET PET-G CFp. 1
FormFutura CarbonFil CF03Strength XY, MPa44Strength Z, MPa—Modulus XY, GPa3.52Charpy notched, kJ/m²4.6IzodHDT 0.45, °C77HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–270Bed, °C60–80Chamber, °CnoneDrying, °C, hdry first
FormFutura CarbonFil CF03FormFutura
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| FormFutura, TECHNICAL DATA SHEET CarbonFil CF037 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile modulus orientation not stated | 3515 MPap. 1: Tensile modulus | ISO 527As the sheet prints it: ISO 527-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 44 MPap. 1: Tensile strength at break | ISO 527As the sheet prints it: ISO 527-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 5.5 %p. 1: Tensile elongation | no standard stated | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength | 4.6 kJ/m2p. 1: Izod impact strength (notched) | ISO 180 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT | 77 °Cp. 1: HDT | ISO 306 | not in the median: set apart (never used to pass), no stated test load |
| Density | 1.29 g/cm3p. 1: Density | no standard stated | |
| Fibre content | 3%p. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 240–270 °CBambu Lab Filament Guide
- Bed
- 60–80 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- required, schedule not statedown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Drying it is recommended to dry the material prior to usage and to 3D print it directly from a dry boxFormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1: Storage and handling
Price
Not in the price sample.
Its 2 documents
What the maker says (6)
- Good for
PETG end use parts that do not require the full strength of carbon.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1 - Benefits
It is very easy to 3D print with CarbonFil CF03.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1 - Benefits
Still, it shows great resistance to chemicals and machinability properties.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1 - Benefits
High speed printing compatible.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1 - Precision and tolerance
It prints with great precision and superb layer adhesion.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1 - Surface finish
This results in 3D prints with a magnificent carbon finish and no visible layers.
FormFutura, TECHNICAL DATA SHEET CarbonFil CF03p. 1
Nanovia PETG CFStrength XY, MPa50Strength Z, MPa—Modulus XY, GPa4.15Charpy notched, kJ/m²20HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C220–240Bed, °C80–90Chamber, °C20Drying, °C, h604 h
Nanovia PETG CFNanovia
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanovia8 values | |||
| Tensile modulus XY | 4150 MPap. 1: Young’s modulus (+45° / -45° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | in the median |
| Tensile modulus orientation not stated | 5800 MPap. 1: Young’s modulus | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins at 0°, along with the tension stress. | not in the median: another value of this product is in it |
| Tensile strength (yield or break not stated) XY | 50 MPap. 1: Ultimate strength (+45° / -45° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | in the median |
| Tensile strain at strength XY | 2.7 %p. 1: Elongation ultimate strength (+45° / -45° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | listed under other properties |
| Tensile strain at strength orientation not stated | 2.3 %p. 1: Elongation ultimate strength | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins at 0°, along with the tension stress. | listed under other properties |
| Charpy impact strength | 20 kJ/m2p. 1: Charpy (notched) | no standard stated | in the median |
| Glass transition temperature | 80 °Cp. 1: Tg | no standard stated | in the median |
| Density | 1.35 g/cm3p. 1: Density | ISO 1183 | |
Print settings
- Nozzle
- 220–240 °Cown data sheet
- Bed
- 80–90 °Cown data sheet
- Heated chamber
- 20 °Cown data sheet
- Drying
- optional: 60 °C for 4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 220 – 240 °C; Bed 80 – 90 °C; Chamber 20 °C; Drying Dehydrate for 4h at 60°C prior to printing after prolonged exposure to humidity.Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1: Recommended printing settings; p. 1: Drying note; p. 1: Nozzle (minimal); p. 1: Printing
Price
Not in the price sample.
Its 3 documents
What the maker says (7)
- Good for
Ideal for structural pieces
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Benefits
Easy to print
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Benefits
This composite 3D filament has been specially designed to be compatible with standard 3D printers equipped with a heated bed.
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Pitfalls and limitations
For an outdoor usage, it’s recommended either paint or apply a protective UV coating.
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Warping and shrinkage
Nanovia PETg CF allows for the creation of structural 3D prints with low warping thanks to its compound carbon fibers structure.
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Nozzle wear
A reinforced nozzle, suitable for abrasive materials is recommended.
Nanovia, Nanovia PETG CF : Carbon fiber reinforced : Nanoviap. 1 - Pitfalls and limitations
The product is not approved for medical applications.
Nanovia, PETG CF official material safety data sheetp. 2: Section7.2 safe storage/use exclusion
Chemicals and environment (2)
- Organic solvent resistance: described in words
Some Organic solvents could degrade the material.
Nanovia, PETG CF official material safety data sheetp. 2: Section10.3 possible side reactions - UV and outdoor: described in words
Biodegradation and elimination (H2O): the product is inert and can lead some surface degradation under the UV action.
UVNanovia, PETG CF official material safety data sheetp. 3: Section12.2 persistence/degradability, own English column
Spectrum PET-G CarbonStrength XY, MPa45Strength Z, MPa—Modulus XY, GPa4.25Charpy notched, kJ/m²—HDT 0.45, °C72HDT 1.8, °C—Price, CAD/kg—Nozzle, °C230–255Bed, °C60–80Chamber, °CnoneDrying, °C, h658 h
Spectrum PET-G CarbonSpectrum
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Spectrum, TECHNICAL DATA SHEET PET-G Carbon6 valuesThe same values also in Spectrum, KARTA TECHNICZNA PET-G Carbon. | |||
| Tensile modulus orientation not stated | 4250 MPap. 1: Elastic modulus 3D printing | ISO 527As the sheet prints it: ISO 527-1 | in the median |
| Tensile break strength orientation not stated | 45 MPap. 1: Tensile strength at break (3D printing) * | ISO 527As the sheet prints it: ISO 527-1 | in the median |
| Elongation at break orientation not stated | 4,90 %p. 1: Tensile elongation at break (3D printing) * | ISO 527As the sheet prints it: ISO 527-1 | in the median |
| Vicat softening temperature | 80 °Cp. 1: VICAT, 50 N (heating rate 50°C/h)also in Spectrum, KARTA TECHNICZNA PET-G Carbon | ISO 306As the sheet prints it: 50 N ISO 306 | |
| Density | 1.32 g/cm3p. 1: Specific Gravity | ISO 1183 | |
| Fibre content | 10% addition of carbon fibresp. 1: Fibre content | no standard stated | |
| Spectrum, KARTA TECHNICZNA PET-G Carbon1 value | |||
| Charpy impact strength orientation not stated | 17 kJ/m2p. 1: Udarność wg. Charpy'ego (próbka 80x10x4 mm) Bez karbu, druk 3D | ISO 179As the sheet prints it: ISO 179-1eU; specimen size=80x10x4 mm | not in the median: unnotched |
| Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIO1 value | |||
| HDT at 0.45 MPa | 72°Cp. 4: HDT B | no standard namedAs the sheet prints it: method=B | in the median |
Print settings
- Nozzle
- 230–255 °Cown data sheet
- Bed
- 60–80 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
Its 4 print profiles, in the documents' words
- Nozzle 230-255°C; Bed 60-80°CSpectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1: Recommended printing settings
- Bed 60-80 °CSpectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIOp. 4: Bed temp. [°C]; p. 4: Dry box recommended; p. 4: Ruby or hardened nozzle recommended; p. 4: Adhesive
- No temperature statedSpectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29p. 22: Dry box recommended; p. 22: Ruby or hardened nozzle recommended
- Nozzle 230-255°C; Bed 60-80°CSpectrum, KARTA TECHNICZNA PET-G Carbonp. 1: Temperatura dyszy; p. 1: Temperatura stołu; p. 1: Suszarka do filamentu; p. 1: * ustawienia oparto na dyszy o średnicy 0,4 mm
Price
Not in the price sample.
Its 5 documents
What the maker says (10)
- Benefits
improved abrasion resistance
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Benefits
Spectrum PET-G Carbon is a modified, PET-G-based filament blended with carbon fibres which contributes to a considerably higher rigidity, hardness and tensile resistance, while retaining low shrinkage and very good adhesion to build platforms typical for the pure PET-G.
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Benefits
higher plasticisation temperaturę as compared to the pure PET-G
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Benefits
much higher compression resistance as compared to the pure PET-G
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Warping and shrinkage
no shrinkage after cooling
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Surface finish
high aesthetic, matte surface quality
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Surface finish
The 10% addition of carbon fibres enables to obtain matte surfaces of printed items, which greatly improves the aesthetic properties of printed items.
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Moisture sensitivity
Dry box not necessary
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Nozzle wear
Ruby or hardened nozzle recommended
Spectrum, TECHNICAL DATA SHEET PET-G Carbonp. 1 - Benefits
10% Carbon fiber reinforced, improved hardness & rigidity
Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29p. 20
FormFutura CarbonFilStrength XY, MPa45Strength Z, MPa—Modulus XY, GPa9.49Charpy notched, kJ/m²5HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C230–265Bed, °C80–90Chamber, °C—Drying, °C, h40–6012 h
FormFutura CarbonFilFormFutura
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| FormFutura, Technical Data Sheet CarbonFil™9 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile modulus orientation not stated | 9495 Mpap. 1: Tensile modulus | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 92 Mpap. 1: Tensile strength | ISO 527 | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 3.4 %p. 1: Elongation at break | ISO 527 | not in the median: another value of this product is in it |
| Charpy impact strength | 5 KJ/m²p. 1: Impact strength | ISO 179tested at 23° C (73° F)notched | not in the median: set apart (never used to pass), test bar not described as printed |
| Vicat softening temperature | 79° C °Cp. 1: Viscat softening temp. | ISO 306As the sheet prints it: ISO 306; 0.455 Mpa (66psi) | |
| Density | 1.19 g/ccphysically implausiblep. 1: Specific gravity | ISO 1183 | |
| Water absorption | 0.13 %p. 1: Water absorption - - - Moisture absorption ± Mechanical | no standard stated | |
| Melt volume-flow rate | 3.7 cm³/10minp. 1: Melt flow rate | ISO 1133As the sheet prints it: ISO 1133; 5Kg | |
| Fibre content | 20% ultra-light and relatively long stringer carbon fibresp. 1: Fibre content | no standard stated | |
| FormFutura, Technical Data Sheet CarbonFil7 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile break strength orientation not stated | 45 MPap. 1: Tensile strenght at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 4,9 %p. 1: Elongation at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural modulus orientation not stated | held back: the sheet's unit or table layout is unclearheld backp. 1: Flexural modulus | ISO 527As the sheet prints it: ISO 527-1 | not in the median: held back |
| Charpy impact strength orientation not stated | held back: the sheet's unit or table layout is unclearheld backp. 1: Impact strenght | ISO 179As the sheet prints it: ISO 179-1eU | not in the median: held back |
| Vicat softening temperature | 80 °Cp. 1: Vicat softening temperature | ISO 306 | |
| Density | 1,32 g/cm3p. 1: Specific gravity | ISO 1183 | |
| Fibre content | 15% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 230–265 °Cown data sheet
- Bed
- 80–90 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 40–60 °C for 12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its 2 print profiles, in the documents' words
- Nozzle ± 230 - 265° CFormFutura, Technical Data Sheet CarbonFil™p. 1: Recommended printing settings
- Nozzle 230 - 275 °C; Bed 80 - 90 °C; Drying Recommended 40 - 60 °C 12 hFormFutura, Technical Data Sheet CarbonFilp. 1: Recommended pretreatment, Print with, Recommended print settings regular speed
Price
Not in the price sample.
Its 3 documents
What the maker says (2)
- Benefits
Our CarbonFil filament is based upon the unique PETG blend of our HDglass compound and is reinforced with 20% ultra-light and relatively long stringer carbon fibres, which has resulted in an exceptionally stiff carbon-fibre reinforced 3D printer filament.
FormFutura, Technical Data Sheet CarbonFil™p. 1 - Benefits
CarbonFil is twice as stiff as HDglass and yet it is even 10% more impact resistant, which is a remarkable feature for carbon-fibre reinforced filament.
FormFutura, Technical Data Sheet CarbonFil™p. 1
iSANMATE PETG CFStrength XY, MPa43.8Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–270Bed, °C60–80Chamber, °CnoneDrying, °C, h658 h
iSANMATE PETG CFiSANMATE
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| iSANMATE, PETG CF Filament Technical Data Sheet10 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile strength (yield or break not stated) orientation not stated | 43.8 MPap. 1: Tensile strength | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 14.6 %p. 1: Elongation at break | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural modulus orientation not stated | 2280 MPap. 1: Flexural modulus | ASTM D790 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 88 MPap. 1: Bending strength | ASTM D790 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength orientation not stated | 3.282 KJ/m²p. 1: Impact strength | ISO 179 | not in the median: notch not stated |
| Vicat softening temperature | 72 ℃p. 1: Vicat softening point A/120 | ASTM D648As the sheet prints it: ASTM D-648; method=A/120 | |
| Melting temperature | 190-210 ℃p. 1: melting point | DSC | |
| Density | 1.25 g/cm3p. 1: Density | ASTM D792 | |
| Water absorption | <1 %p. 1: Water Absorption | ASTM D570 | |
| Melt mass-flow rate | 10 g/10minp. 1: Melt Index Rockwell hardness R | ASTM D1238As the sheet prints it: 170℃ 2160g) ASTM D-1238 | |
Print settings
- Nozzle
- 240–270 °CBambu Lab Filament Guide
- Bed
- 60–80 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
What the maker says (1)
- Benefits
PETG carbon fiber material has good rigidity and heat resistance, as follows: 1.The strength is 15 -30% higher than ordinary PETG; 2.High rigidity and good toughness; 3.Excellent heat resistance and short processing cycle; 4.Excellent hydrolysis resistance and product stability; 5.Good processability.
iSANMATE, PETG CF Filament Technical Data Sheetp. 1
Nobufil PETG CFStrength XY, MPa55Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²2IzodHDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C245–265Bed, °C70–90Chamber, °CnoneDrying, °C, h60–703–6 h
Nobufil PETG CFNobufil
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Nobufil, Technical Datasheet PETG CF13 values | |||
| Tensile strength (yield or break not stated) orientation not stated | 55 MPap. 1: Tensile strength, FDM H | ISO 527print settingsFDM H column (the sheet does not say what H is) | not in the median: set apart (never used to pass), no stated orientation |
| Tensile strength (yield or break not stated) orientation not stated | 59 MPap. 1: Tensile strength, Injection | ISO 527print settingsInjection column | not in the median: measured on a moulded bar |
| Elongation at break orientation not stated | 11,6 %p. 1: Elongation at break, FDM H | ISO 527print settingsFDM H column (the sheet does not say what H is) | not in the median: set apart (never used to pass), no stated orientation |
| Elongation at break orientation not stated | 17,3 %p. 1: Elongation at break, Injection | ISO 527print settingsInjection column | not in the median: measured on a moulded bar |
| Flexural modulus orientation not stated | 3300 MPap. 1: Flexural modulus | ISO 178 | not in the median: measured on a moulded bar |
| Flexural strength orientation not stated | 81 MPap. 1: Flexural strength | ISO 178 | not in the median: measured on a moulded bar |
| Izod impact strength orientation not stated | 2 kJ/m²p. 1: Izod Impact strength notched, FDM H | ISO 180print settingsFDM H column (the sheet does not say what H is) | not in the median: set apart (never used to pass), no stated orientation |
| Izod impact strength orientation not stated | 2,2 kJ/m²p. 1: Izod Impact strength notched, Injection | ISO 180print settingsInjection column | not in the median: measured on a moulded bar |
| Izod impact strength orientation not stated | 23 kJ/m²p. 1: Izod Impact strength unnotched, FDM H | ISO 180print settingsFDM H column (the sheet does not say what H is) | not in the median: unnotched |
| Izod impact strength orientation not stated | 74 kJ/m²p. 1: Izod Impact strength unnotched, Injection | ISO 180print settingsInjection column | not in the median: measured on a moulded bar |
| HDT at 1.8 MPa | 93 °Cphysically implausiblep. 1: HDT A | ISO 75As the sheet prints it: HDT A ISO 75 | not in the median: physically implausible as published |
| Density | 1,34 g/cm³p. 1: Density | ISO 1183 | |
| Fibre content | 10% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 245–265 °Cown data sheet
- Bed
- 70–90 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 60–70 °C for 3–6 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 255°C ± 10; Bed 80°C ± 10; Drying Pre-dry material for 3-6 hours at 60 - 70°C (max.).Nobufil, Technical Datasheet PETG CFp. 1: Recommended printing settings; p. 1: Drying note
Price
Not in the price sample.
Its 2 documents
What the maker says (1)
- Nozzle wear
Nozzle hardened
Nobufil, Technical Datasheet PETG CFp. 1
SIDDAMENT PETG CF V2sStrength XY, MPa59Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–270Bed, °C60–80Chamber, °CnoneDrying, °C, h60≥ 12 h
SIDDAMENT PETG CF V2sSIDDAMENT
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SIDDAMENT, PETG CF Technical Data Sheet6 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile strength (yield or break not stated) orientation not stated | 59 MPap. 1: Tensile Strength | no standard stated | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 102 %physically implausiblep. 1: Breaking Elongation | no standard stated | not in the median: physically implausible as published |
| Flexural modulus orientation not stated | 65 MPap. 1: Bending modulus | no standard stated | not in the median: set apart (never used to pass), test bar not described as printed |
| Impact strength, test unclear | 8.5 Kj/m2p. 1: Impact Strength | no standard statedWhich test: probably Izod | listed under other properties |
| Density | 1.23 g/cm3p. 1: Density | no standard stated | |
| Fibre content | 15% by weight chopped fibersp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 240–270 °CBambu Lab Filament Guide
- Bed
- 60–80 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 60 °C for ≥ 12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Drying It is recommended to dry the consumables in a hot air oven at 60℃ for at least 12 hoursSIDDAMENT, PETG CF Technical Data Sheetp. 1: Drying note
Price
Not in the price sample.
Its 2 documents
What the maker says (3)
- Benefits
High stiffness
SIDDAMENT, PETG CF Technical Data Sheetp. 1 - Benefits
High temperature resistance
SIDDAMENT, PETG CF Technical Data Sheetp. 1 - Warping and shrinkage
Low warping
SIDDAMENT, PETG CF Technical Data Sheetp. 1
Chemicals and environment (1)
- Post-processing: described in words
After the model is printed, it is recommended to dry it in an oven at a temperature of 70°C for 6~8 hours to improve the strength of the model.
SIDDAMENT, PETG CF Technical Data Sheetp. 1: Post-processing note
Spectrum THE FILAMENT PETG CFStrength XY, MPa57.6Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C70HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–265Bed, °C60–70Chamber, °CnoneDrying, °C, h658 h
Spectrum THE FILAMENT PETG CFSpectrum
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CF6 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile yield strength orientation not stated | 57.6 MPap. 1: Tensile Strength at Yield | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 20.4 MPap. 1: Tensile Strength at Break | ISO 527 | not in the median: another value of this product is in it |
| Charpy impact strength | 3.2 kJ/m2p. 1: Impact Strength - Charpy method | ISO 179 | not in the median: notch not stated |
| HDT | 70 °Cp. 1: Heat Deflection Temperature | ASTM D648As the sheet prints it: D 648 | not in the median: set apart (never used to pass), no stated test load |
| Density | 1.29 g/cm3p. 1: Specific Gravity | ASTM D792As the sheet prints it: D 792 | |
| Fibre content | 3% CFp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 240–265 °Cown data sheet
- Bed
- 60–70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 240-265°C; Bed 60-70°CSpectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1: Recommended printing settings; p. 1: Footnote *; p. 1: Dry box recommended
- Nozzle 240-265°C; Bed 60-70°CSpectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1: Recommended printing settings; p. 1: Footnote *; p. 1: Dry box recommended
Price
Not in the price sample.
Its 3 documents
What the maker says (4)
- Benefits
3% CF for durability and flexibility; optimized formula; beginner-friendly
Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1 - Surface finish
Surface finish matte, carbon appearance
Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1 - Moisture sensitivity
Dry box recommended: No
Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1 - Nozzle wear
Ruby or hardened nozzle recommended: Yes
Spectrum, TECHNICAL DATA SHEET THE FILAMENT PETG CFp. 1
eSUN PETG CFStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg35Nozzle, °C245–265Bed, °C70Chamber, °CnoneDrying, °C, h658 h
eSUN PETG CFeSUN
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| eSUN, ePETG-CF Technical Data Sheet7 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile strength (yield or break not stated) orientation not stated | 24.28 MPap. 1: Tensile Strength GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Elongation at break orientation not stated | 4.70 %p. 1: Elongation at Break GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Flexural modulus orientation not stated | 2951.4 MPap. 1: Flexural Modulus GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Flexural strength orientation not stated | 80.34 MPap. 1: Flexural Strength GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Izod impact strength | 1.5 kJ/m2p. 1: IZOD Impact Strength GB/T 1843 | GB/T 1843 | not in the median: measured on a moulded bar |
| HDT at 0.45 MPa | 70.5 ℃p. 1: Heat distortion Temperature | GB/T 1634As the sheet prints it: GB/T 1634 0.45Mpa | not in the median: measured on a moulded bar |
| Density | 1.26 g/cm3p. 1: Density GB/T 1033 | specimen not stated, GB/T 1033 | |
Print settings
- Nozzle
- 245–265 °Cown data sheet
- Bed
- 70 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- optional: 65 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 245 - 265℃; Bed 70℃eSUN, ePETG-CF Technical Data Sheetp. 2: Recommended printing settings: Extruder Temperature; p. 2: Based on
Price
35 CAD/kgits one regular price in the sample
1 listing
- DigitMakers: 35 CAD/kgeSUN PETG-CF Filament 1.75mm 1kg / Black (SKU ESUN-PETGCF-175-1KG-BLK)in its price; seen 30 Sep 2026
Its 2 documents
What the maker says (4)
- Good for
Aerospace • Automotive • Industrial applications
eSUN, ePETG-CF Technical Data Sheetp. 1 - Benefits
High strength Wear resistance Impact resistance
eSUN, ePETG-CF Technical Data Sheetp. 1 - Benefits
Chemical resistance
eSUN, ePETG-CF Technical Data Sheetp. 1 - Benefits
Adding carbon fiber reinforced materials to PETG and modifying, it strengthens the rigidity and toughness of PETG.
eSUN, ePETG-CF Technical Data Sheetp. 1
No product matches "".
Values are for the colour each sheet tested; pigment can change them.