PA6-GF
Glass-Fiber-Reinforced Polyamide 6
11 products from 10 makers. Bambu Lab sells its own filament of this material for the H2C.
- Tensile modulus (XY)
- 4.35GPa
- 4 products · middle half 3.91–4.66
- Tensile strength (XY)
- 82.3MPa
- 6 products · middle half 76.3–87.9
- Tensile strength (Z)
- 60.7MPa
- 3 products · 27–61.4
- Notched Charpy impact
- 8.6kJ/m²
- 2 products · 7.2–10
- HDT at 0.45 MPa
- 186°C
- 7 products · middle half 181–191
- Price
- 84CAD/kg
- 3 products · 77–146
PA6-GF is glass-fibre-reinforced polyamide 6. Makers sell it for gear wheels, bearings and sliding elements, and for demanding industrial and automotive uses. It is semicrystalline, so it carries light load well above its glass transition: its HDT at 0.45 MPa is 186 °C. On the H2C it needs a hardened nozzle, and makers stress dry storage because it is sensitive to moisture.
Partly documented Notched Charpy impact rests on 2 products, tensile strength (Z) and price on 3 products each and tensile modulus (XY) on 4 products. Each figure is the median of the products that publish it comparably, and beside it the middle half of them; a value on a test bar no document describes as printed, or with no stated test load, is set apart, except a heat deflection of a plastic that cannot crystallise, which its glass transition sets, unless its document points to a moulded or resin bar.
On the H2C
Printing in full- Nozzle
- 260–290 °C
- most products that give one
- Bed
- 80–100 °C
- 3 of 7 that give one
- Heated chamber
- 25–60 °C
- most products that give one
- Drying
- 80–110 °C, 6–12 h
- 9 of 11 products call for it; 2 more give it as optional
- Nozzle type
- hardened
- 8 of 11 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 3 more
Beyond the H2C's limits (nozzle 350 °C, bed 120 °C, heated chamber 65 °C): bed for 1 product.
Among the materials
Against PA6-CF, PA6-GF is 36 % less tough in notched impact, 35 % less expensive and 26 % stronger across the layers. Against PPA-CF, PA6-GF is 43 % less stiff and 24 % weaker flat, and its HDT at 0.45 MPa is 34 °C lower. Among the materials, PA6-GF has a high tensile modulus (XY), tensile strength (XY), tensile strength (Z), HDT at 0.45 MPa and density: each is in the top quarter of the materials that publish it. The rest of its key properties sit in the middle half.
Against its alternatives, PA6-GF has the highest tensile strength (Z) and the lowest price
How does it compare with what an engineer would buy instead?
- PA6-GF: its products' median and middle half
- an alternative
- lowest to highest
- each material's median (top row)
- set apart: test bar not described as printed, or no stated load
- beyond the scale
Each row is a material, each column a property: the bar is the middle half of a material's products, the tick their median, the hairline their lowest to highest; the ticks above the rows are every material's median.
The figure as a table
| Material | Modulus (XY) (GPa) | Strength (XY) (MPa) | Strength (Z) (MPa) | Notched Charpy (kJ/m²) | HDT 0.45 MPa (°C) | Price (CAD/kg) |
|---|---|---|---|---|---|---|
| PA6-GF (this material) | 4.35 (3.91–4.66) · 4 | 82.3 (76.3–87.9) · 6 | 60.7 · 3 | 8.6 · 2 | 186 (181–191) · 7 | 84 · 3 |
| PA6 | 2.1–3.3 as published (6) | 50 · 1 | — | 5–6.8 as published (4) | 60–186 as published (5) | 163 · 0 |
| PA6-CF | 4.37 (4.09–4.61) · 6 | 70 (62.3–104) · 8 | 48 · 3 | 13.4 · 3 | 193 (185–202) · 6 | 130 (113–160) · 4 |
| PPA-CF | 7.65 (7.1–9.1) · 4 | 108 (103–123) · 4 | 57 · 1 | 6.5 · 1 | 220 (220–227) · 5 | 255 · 1 |
| PAHT-CF | 8.39 · 3 | 103 · 3 | 37.9 · 3 | 13.8 · 2 | 170 · 2 | 124 · 1 |
| PPS-CF | 8 (7.46–8) · 5 | 87 (63–95) · 5 | 28.2 · 3 | 5.75 · 2 | 251 (245–253) · 5 | 210 · 2 |
Each cell is the median of the products ranked, its middle half in brackets, and how many.
Where PA6-GF sits among the 128 rigid materials on file
Where is it in the landscape: stiffness against strength, heat resistance against price?
- PA6-GF: median, middle half as a cross
- a PA6-GF product
- an alternative
- another material
- beyond the scale
Tensile strength (XY) against tensile modulus (XY)
MPa, log scale
Tensile modulus (XY), GPa, log scale
HDT at 0.45 MPa against price
°C
Price, CAD/kg, log scale
Grey points are every other rigid material's medians; the alternatives are named.
The figure as a table
| Material | Tensile modulus (XY) | Tensile strength (XY) | Price | HDT at 0.45 MPa |
|---|---|---|---|---|
| PA6-GF (this material) | 4.35 GPa · 4 | 82.3 MPa · 6 | 84 CAD/kg · 3 | 186 °C · 7 |
| PA6 | 2.1–3.3 GPa as published | 50 MPa · 1 | 163 CAD/kg · 0 | 60–186 °C as published |
| PA6-CF | 4.37 GPa · 6 | 70 MPa · 8 | 130 CAD/kg · 4 | 193 °C · 6 |
| PPA-CF | 7.65 GPa · 4 | 108 MPa · 4 | 255 CAD/kg · 1 | 220 °C · 5 |
| PAHT-CF | 8.39 GPa · 3 | 103 MPa · 3 | 124 CAD/kg · 1 | 170 °C · 2 |
| PPS-CF | 8 GPa · 5 | 87 MPa · 5 | 210 CAD/kg · 2 | 251 °C · 5 |
Mechanical properties
Printed flat (XY), PA6-GF typically reaches a tensile strength of 82.3 MPa at a modulus of 4.35 GPa, and breaks at 4.95 % elongation. In bending, its flexural strength is typically 134 MPa at a flexural modulus of 4.31 GPa.
PA6-GF's products spread most in elongation at break: the middle half runs 3.52–6.06 %
How strong, stiff and tough are its products, and which stand out?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
One mark per product on each property's scale (zoomed where its products sit close together, as its label says); the band is the middle half of the products the median counts, and the line the median.
Hover or select a product to find it in every figure; its name opens its card on the Products page.
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| Tensile strength (XY) (MPa) | 6 | 82.3 | 76.3–87.9 | 3DXTECH AMIDEX Nylon GF30, 62.8 | Flashforge PA6-GF20, 98.9 | 3 | 0 |
| Tensile modulus (XY) (GPa) | 4 | 4.35 | 3.91–4.66 | Bambu Lab PA6-GF, 2.85 | Polymaker FIBERON PA6 GF25, 5.36 | 3 | 0 |
| Elongation at break (XY) (%) | 6 | 4.95 | 3.52–6.06 | Polymaker FIBERON PA6 GF25, 2.4 | SUNLU PA6-GF, 13 | 3 | 0 |
Every PA6-GF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
| Product | Tensile strength (Z) | Notched Charpy impact | Notched Izod impact |
|---|---|---|---|
| Bambu Lab PA6-GF | 27 MPaafter annealing | 7.2 kJ/m²after annealing | not published |
| Polymaker PolyMide GF | 61.4 MPaafter annealing | not published | not published |
| Spectrum PA6 Low | not published | 4 kJ/m²not described as printed | not published |
| SUNLU PA6-GF | not published | not published | 10.5 kJ/m² |
| Polymaker FIBERON GF25 | 60.7 MPaafter annealing | 10 kJ/m²after annealing | not published |
| FormFutura STYX PA6-GF30 | not published | 4 kJ/m²not described as printed | not published |
In grey, a value a product reads from a data sheet it shares, where its own sheet is silent.
Across the layers (Z), PA6-GF keeps 73 % of its flat strength and 68 % of its flat stiffness
What does a printed part lose across the layers (Z) against flat (XY), and is that usual?
- a product
- measured after annealing
- equal share: 100, 75, 50 and 25 %
- PA6-GF's median share
- an alternative
Tensile strength
Z keeps 73 % of XY, median of 3 products
flat (XY), MPa
Share kept: PA6-GF 73 % · PA6-CF 49 % · PPS-CF 45 % · PPA-CF 34 % · PAHT-CF 31 %
Tensile modulus
Z keeps 68 % of XY, median of 3 products
flat (XY), GPa
Share kept: PA6-GF 68 % · PA6-CF 46 % · PAHT-CF 42 % · PPS-CF 36 % · PPA-CF 36 %
Elongation at break
Z keeps 85 % of XY, median of 3 products
flat (XY), %
Share kept: PA6-GF 85 % · PPS-CF 77 % · PA6-CF 77 % · PAHT-CF 49 % · PPA-CF 28 %
Each point is a product that publishes both from one sheet: below the 100 % ray it keeps less across the layers than flat. Under each plot, the median share its alternatives' products keep.
The figure as a table
| Product | Property | Flat (XY) | Across (Z) | Z as a share of XY |
|---|---|---|---|---|
| Bambu Lab PA6-GF | Tensile strength | 75 MPa | 27 MPa | 36 % |
| Polymaker PolyMide PA6 GF | Tensile strength | 84.5 MPa | 61.4 MPa | 73 % |
| Polymaker FIBERON PA6 GF25 | Tensile strength | 80.1 MPa | 60.7 MPa | 76 % |
| Bambu Lab PA6-GF | Tensile modulus | 2.85 GPa | 1.95 GPa | 68 % |
| Polymaker PolyMide PA6 GF | Tensile modulus | 4.43 GPa | 3.33 GPa | 75 % |
| Polymaker FIBERON PA6 GF25 | Tensile modulus | 5.36 GPa | 3.38 GPa | 63 % |
| Bambu Lab PA6-GF | Elongation at break | 3.9 % | 2.3 % | 59 % |
| Polymaker PolyMide PA6 GF | Elongation at break | 3.4 % | 2.9 % | 85 % |
| Polymaker FIBERON PA6 GF25 | Elongation at break | 2.4 % | 4 % | 167 % |
| PA6-CF (alternative) | Tensile strength | 49 % · 3 | ||
| PPA-CF (alternative) | Tensile strength | 34 % · 1 | ||
| PAHT-CF (alternative) | Tensile strength | 31 % · 3 | ||
| PPS-CF (alternative) | Tensile strength | 45 % · 3 | ||
| PA6-CF (alternative) | Tensile modulus | 46 % · 2 | ||
| PPA-CF (alternative) | Tensile modulus | 36 % · 1 | ||
| PAHT-CF (alternative) | Tensile modulus | 42 % · 3 | ||
| PPS-CF (alternative) | Tensile modulus | 36 % · 3 | ||
| PA6-CF (alternative) | Elongation at break | 77 % · 2 | ||
| PPA-CF (alternative) | Elongation at break | 28 % · 1 | ||
| PAHT-CF (alternative) | Elongation at break | 49 % · 3 | ||
| PPS-CF (alternative) | Elongation at break | 77 % · 3 |
Flat and across the layers, property by property
Flat and across the layers
| Property | Printed flat (XY) | Across the layers (Z) | Z as a share of XY | ||
|---|---|---|---|---|---|
| Median | Products | Median | Products | ||
| Tensile strength MPa | 82.376.3–87.9 | 6 | 60.7 | 3 | 73 %3 products |
| Tensile modulus GPa | 4.353.91–4.66 | 4 | 3.33 | 3 | 68 %3 products |
| Elongation at break % | 4.953.52–6.06 | 6 | 2.9 | 3 | 85 %3 products |
| Flexural strength MPa | 134120–136 | 5 | 75.5 | 2 | 59 %2 products |
| Flexural modulus GPa | 4.313.67–4.64 | 5 | 2.57 | 2 | 64 %2 products |
The middle half of the products under each median. The share is each product's Z value as a part of its XY value, from one sheet and one state, and the median of those shares. How XY and Z differ.
Thermal properties
PA6-GF's HDT is typically 186 °C under 0.45 MPa and 157–158 °C under 1.8 MPa, with its glass transition typically at 70 °C. Semicrystalline, it carries light load well above its glass transition. As published, Vicat softening is typically 211 °C and melting typically 217 °C.
Most PA6-GF products deflect at 181–191 °C under 0.45 MPa
Where do its products soften under load?
- a product
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- middle half and median
The figure as a table
| Property | In the median | Median | Middle half | Lowest in the median | Highest in the median | As published | Added filler or additive |
|---|---|---|---|---|---|---|---|
| HDT at 0.45 MPa (°C) | 7 | 186 | 181–191 | Stratasys PA6/66-GF30-FR, 161 | SUNLU PA6-GF, 205 | 3 | 0 |
| Glass transition (Tg) (°C) | 5 | 70 | 67–70 | SUNLU PA6-GF, 65 | Polymaker FIBERON PA6 GF25, 70 | 0 | 0 |
Every PA6-GF product that publishes these values is drawn; each value, with its document and conditions, is on the Products page.
| Product | HDT at 1.8 MPa |
|---|---|
| Bambu Lab PA6-GF | 158 °Cafter annealing |
| Polymaker PolyMide GF | 157 °C |
| Spectrum PA6 Low | 65 °Cnot described as printed |
| Polymaker FIBERON GF25 | 157 °Cafter annealing |
| FormFutura STYX PA6-GF30 | 65 °Cnot described as printed |
In grey, a value a product reads from a data sheet it shares, where its own sheet is silent.
Printing on the H2C
PA6-GF softens near 186 °C, above the H2C's 65 °C chamber; 1 product asks for more than the H2C gives
What does printing it on the H2C take, and how hot can a part get?
- share of the products that accept each temperature
- what most products accept
- one end given ("at least")
- the H2C's limit, and beyond it
- a product
- PA6-GF: its products' median and middle half
- as published, under each sheet's own test
Printing it on the H2C
In service
°C
One temperature axis for the settings a print needs and the temperatures a part meets. A setting's shade is how many of the products whose sheets give a window accept each degree; the H2C's limit closes its row.
The figure as a table
| Setting or property | Most products, or the median | Products | H2C limit |
|---|---|---|---|
| Nozzle | 260–290 °C | 9 | 350 °C |
| Bed | 25–50 °C; 40–50 °C; 60–70 °C; 80–100 °C; 80–100 °C; 80–110 °C; 120–140 °C | 7 | 120 °C |
| Heated chamber | 25–60 °C | 3 | 65 °C |
| Drying | 80–110 °C, 6–12 h | 5 | — |
| Glass transition (Tg) | 70 °C (67–70 °C) | 5 | — |
| HDT at 1.8 MPa | 157 °C | 3 | — |
| HDT at 0.45 MPa | 186 °C (181–191 °C) | 7 | — |
| Vicat softening temperature | 210–212 °C | 2 | — |
| Melting temperature | 215–225 °C | 4 | — |
Windows read from the Bambu Lab Filament Guide are not shaded: the guide speaks for every product that reads it.
| Setting | Most PA6-GF products | Bambu Lab Filament Guide (PA6-GF column) |
|---|---|---|
| Nozzle | 260–290 °C most products that give one | 260 - 290 ℃ |
| Bed | 80–100 °C 3 of 7 that give one | Smooth PEI Plate (100 - 120 °C) Textured PEI Plate (100 - 120 °C) |
| Heated chamber | 25–60 °C most products that give one | enclosure required |
| Drying | 80–110 °C, 6–12 h 9 of 11 products call for it; 2 more give it as optional | 80 °C for 8–12 h |
| Nozzle type | hardened 8 of 11 products' sheets ask for one; the Bambu Lab Filament Guide says hardened for 3 more | hardened |
Where a product's own sheet is silent, its setting comes from a sheet it shares or from the Bambu Lab Filament Guide; each product's card says which.
After printing
Three products publish values measured after annealing, on schedules from 80 °C for 12 h to 100 °C for 16 h.
Moisture conditioning refers to allowing the print to absorb moisture. This is inevitble since nylons are hygroscopic, but you can expedite the process by keeping the print in a high humidity climate, or submerging them in water, for 48 hours. All of our test specimens were annealed at 100˚C for 16 hours, and then immerged in water at 60˚C for 48 hours. The average moisture content of specimens is 2.57%.
Polymaker FIBERON PA6 GF25, maker's product page or guide, p. 1Placing the printed part in a convection oven set between 80 to 130 degrees Celsius for 5 to 12 hours can further enhance the strength and rigidity of the print. Note: The effectiveness of this process depends on the structure, size, and conditions of the printed model. Some models may warp or deform after annealing. For more details, please refer to: Work after Printing Finished on WIKI.
Bambu Lab PA6-GF, maker's product page or guide, p. 1After the printing process, it is recommended to anneal the model in the oven at 80 - 100°C for 6 hours.
Polymaker PolyMide PA6 GF, data sheet, p. 5
What makers say about printing it
Moisture sensitivity
PolyMide™ PA6-GF is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker PolyMide PA6 GF, data sheet, p. 5
Nozzle wear
Normally, the life of a brass nozzle would be approximately 9h.
Polymaker PolyMide PA6 GF, data sheet, p. 5
More from makers: printing advice, warping and shrinkage, supports and removal, adhesion between layers and odour and emissions
Printing advice
Additionally, a nozzle diameter of at least 0.6 mm should be used to prevent clogging and ensure smooth extrusion.
Extrudr DURAPRO PA6 GF, data sheet, p. 1
Warping and shrinkage
High glass fibre content provides very low processing shrinkage.
Spectrum PA6 Low Warp GF30, data sheet, p. 1
Supports and removal
Otherwise the support structure can be permanently bonded to the model.
Polymaker PolyMide PA6 GF, data sheet, p. 5
Adhesion between layers
The material exhibits excellent thermal and mechanical properties without sacrificing the layer adhesion.
Polymaker PolyMide PA6 GF, data sheet, p. 2
Odour and emissions
Odor Odorless
Bambu Lab PA6-GF, data sheet, p. 3
Products
11 products from 10 makers; the most from Polymaker (2).
- Most documented: Bambu Lab PA6-GF, and 1 other that publishes as much.
- Highest tensile strength (XY): Flashforge PA6-GF20, 98.9 MPa.
- Highest tensile strength (Z): Polymaker PolyMide PA6 GF, 61.4 MPa, measured after annealing at 80 °C for 6 h.
- Keeps the most strength across the layers: Polymaker FIBERON PA6 GF25, 76 % of its flat tensile strength (the median product keeps 73 %).
- Highest HDT at 0.45 MPa: SUNLU PA6-GF, 205 °C.
- Lowest price: Bambu Lab PA6-GF, 77 CAD/kg.
These are published values, not recommendations: the selector judges each product against your requirements.
Uses, limitations and chemicals
What it is sold for
Purefil PA6 GF10 has a dimensional stability temperature of up to 210°C and is therefore particularly suitable for high-temperature applications.
Fabru Polyamid 6 glass fiber 10% (PA6 GF10), data sheet, p. 1Exceptional Strength, Stiffness, and Heat Resistance Fiberon™ PA6-GF25 is a glass fiber reinforced PA6 (Nylon 6) filament containing 25% glass fiber by weight. This advanced composite material delivers outstanding mechanical strength, high stiffness, and excellent thermal properties, making it ideal for demanding engineering, automotive, aerospace, and industrial applications.
Polymaker FIBERON PA6 GF25, maker's product page or guide, p. 1Gear wheels, bearings, and sliding elements
FormFutura STYX PA6-GF30, data sheet, p. 1
What makers warn about
This Product Is Being Discontinued. Sale is Final And Not Eligible For Returns.
Polymaker PolyMide PA6 GF, maker's product page or guide, p. 1
Finish and accuracy
Masking layer lines with a matt surface finish in 3D printed objects
FormFutura STYX PA6-GF30, data sheet, p. 1matt, carbonised print surface
Spectrum PA6 Low Warp GF30, data sheet, p. 1
Chemicals and environment
| Exposure | What makers say |
|---|---|
| Flammability | Flammable, in its one statement |
| Acid resistance | Not resistant, in all 3 statements |
| Alkali resistance | Not resistant, in 2 of 3 statements |
| Organic solvent resistance | Mixed, 2 statements disagree |
| Oil and grease resistance | Mixed, 2 statements disagree |
| Water solubility | Insoluble, in its one statement |
Makers rarely give the concentration, temperature or duration: treat them as indications, not design data. Each product's statements are on its card.
Resin reference data (for plain PA6, where no maker of these products speaks): it has limited resistance to steam, 100 °C and to water or aqueous solutions at high temperature; it is not resistant to steam sterilization, 134 °C, over 50 cycles (DIN 58946 parts 1-5). Fillers, pigments and printing change this, so it does not stand for these products.
Density and price
PA6-GF's density is typically 1,310 kg/m³, the middle half 1,200–1,340 kg/m³, across 9 products. PA6-GF typically costs 84 CAD/kg, across the 3 products with a regular price in the sample; the lowest is Bambu Lab PA6-GF at 77 CAD/kg.
| Product | Price |
|---|---|
| Bambu Lab PA6-GF | 77 CAD/kg |
| Polymaker FIBERON PA6 | 84 CAD/kg |
| FormFutura STYX PA6-GF30 | 146 CAD/kg |
Regular prices, never sale prices, from 9 Canadian shops and 10 foreign shops, sampled 10 Sep–20 Oct 2026, not live; shipping and tax are not included.
Other properties, as published
14 more properties are published, each under its own sheet's test conditions, so they are listed, not ranked.
The 14 properties, lowest to highest
| Property | Products | Lowest–highest |
|---|---|---|
| Fibre content | 9 | 10–30 % |
| Water absorption | 6 | 1–9 % |
| Melt mass-flow rate | 5 | 3–15.9 g/10 min |
| Crystallization temperature | 3 | 175–183 °C |
| Decomposition temperature | 3 | 330–437 °C |
| Elongation at yield | 3 | 3.2–5 % |
| Mould shrinkage | 2 | 0.4–0.9 % |
| Compression strength | 1 | 22.3–72.4 MPa |
| Flexural elongation at break | 1 | 3.1–4.1 % |
| Hardness | 1 | 82.5 Shore (scale not specified by source) |
| Impact strength, test unclear | 1 | 55.8 kJ/m² |
| Melt volume-flow rate | 1 | 140 cm³/10 min |
| Oxygen index | 1 | 34.1–38 % |
| Surface resistivity | 1 | 1 × 10¹² Ω |
Sources
22 documents from 10 publishers (12 data sheets, 6 makers' product pages and guides, 3 safety data sheets and 1 printer document), read 10 Sep–19 Oct 2026. Each value on PA6-GF's Products page names its document and page, and links to the original.
Bambu Lab, H2C Filamant Printing Guide (the H2C's printer guide): print settings for 11 products.
The Bambu Lab Filament Guide (print settings per material type): read for 7 products whose own sheets are silent.
Every document (22), by publisher
| Publisher | Documents | Values | Products |
|---|---|---|---|
| Polymaker | 5 | 53 | 2 |
| SUNLU | 3 | 25 | 1 |
| Bambu Lab | 3 | 24 | 1 |
| Spectrum | 3 | 13 | 1 |
| Stratasys | 1 | 54 | 1 |
| Extrudr | 1 | 13 | 1 |
| Flashforge | 1 | 13 | 1 |
| 3DXTECH | 1 | 9 | 1 |
| Fabru | 1 | 8 | 1 |
| FormFutura | 1 | 4 | 2 |
- 3DXTECH, AMIDEX Nylon GF30
- Bambu Lab, Bambu Filament Technical Data Sheet - PA6-GF
- Bambu Lab, Bambu Lab Filament Guide
- Bambu Lab, Bambu Lab PA6-GF safety data sheet
- Bambu Lab, H2C Filamant Printing Guide | Bambu Lab Wiki
- Bambu Lab, PA6-GF official maker product page
- Extrudr, TECHNICAL DATA SHEET DURAPRO PA6 GF
- Fabru, Polyamid 6 glass fiber 10% (PA6 GF10)
- Flashforge, Technical Data Sheet PA6-GF20 Filament
- FormFutura, Technical Data Sheet STYX PA6-GF30
- Polymaker, FIBERON PA6 GF25
- Polymaker, FIBERON PA6 GF25 official maker product page
- Polymaker, PolyMide PA6 GF
- Polymaker, PolyMide PA6 GF official maker product page
- Polymaker, PolyMide PA6-GF safety data sheet (EU)
- Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIO
- Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29
- Spectrum, TECHNICAL DATA SHEET PA6 Low Warp GF30
- Stratasys, MATERIAL DATA SHEET PA6/66-GF30-FR
- SUNLU, PA6-GF
- SUNLU, SUNLU PA6-GF safety data sheet
- SUNLU, TECHNICAL DATA SHEET ISO PA6-GF