POM
also called Acetal
3 products from 3 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
3 products
Key
- set apart: test bar not described as printed, or no stated load
- converted price
- not published
How the numbers are worked out
Yousu POMStrength XY, MPa65Modulus XY, GPa—HDT 0.45, °C—HDT 1.8, °C96Price, CAD/kg—Nozzle, °C220–240Bed, °C100–120Chamber, °C—Drying, °C, h—
Yousu POMYousu
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Yousu, Yousu POM 3D Filament Technical Data Sheet11 values | |||
| Tensile strength (yield or break not stated) orientation not stated | 65.0 Mpap. 1: Tensile Strength | ISO 527As the sheet prints it: ISO 527-2; yield | in the median |
| Tensile yield strength orientation not stated | 65.0 Mpap. 1: Tensile Strength (23 °C, yield) | ISO 527As the sheet prints it: ISO 527-2, yield | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 35 %p. 1: Tensile Elongation (23 °C, break) | ISO 527As the sheet prints it: ISO 527-2, break | in the median |
| Flexural modulus orientation not stated | 2.45 Gpap. 1: Flexural modulus | ISO 178tested at 23 °C | not in the median: the only value of its test, shown as published |
| Flexural strength orientation not stated | 84 Mpap. 1: Flexural Strength | ISO 178tested at 23 °C | not in the median: the only value of its test, shown as published |
| Impact strength, test unclear | 7 KJ/m2p. 1: Notched Izod Impact | ISO 179As the sheet prints it: ISO 179/1eA | listed under other properties |
| HDT at 1.8 MPa | 96 ℃ °Cp. 1: Heat Deflection Temperature (1.8 MPa, Unannealed) | ISO 75As the sheet prints it: ISO 75-2/A, 1.8 MPaas printedUnannealed | in the median |
| Density | 1.14 g/cm3p. 1: Density | ISO 1183tested at 23 °C | |
| Melt mass-flow rate | 6 g/10minp. 1: Melt Flow Rate | ISO 1133As the sheet prints it: ISO 1133 (220 °C, 10 kg) | |
| Mould shrinkage orientation not stated | 0.02 %p. 1: Shrink Ratio | no standard stated | |
| Dielectric strength | 19 KV/mmp. 1: Dielectric Strength | no standard namedAs the sheet prints it: 60243-1 | |
Print settings
- Nozzle
- 220–240 °Cown data sheet
- Bed
- 100–120 °Cown data sheet
- Heated chamber
- not stated
- Drying
- not stated
- Hardened nozzle
- not stated
Differs in another document of this product, not used in deciding (a data sheet speaks before a product page, a newer edition before an older one): nozzle in Yousu, 3D printing tips,3d printer filament; bed in Yousu, 3D printing tips,3d printer filament.
Its 2 print profiles, in the documents' words
- Nozzle 220-240℃; Bed 100-120℃Yousu, Yousu POM 3D Filament Technical Data Sheetp. 2: Printing Temp, Bed Temp
- Nozzle 180 °C - 195 °C; Bed 40-60 °CYousu, 3D printing tips,3d printer filamentp. 1: Hot-end temperature; p. 1: Heated-bed temperature
Price
Not in the price sample.
Its 3 documents
What the maker says (1)
- Warping and shrinkage
Shrink Ratio % 0.02
Yousu, Yousu POM 3D Filament Technical Data Sheetp. 1
Grupa Azoty Tarfuse POM 3D FilamentStrength XY, MPa50Modulus XY, GPa1.87HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg121Nozzle, °C210–240Bed, °C100–130Chamber, °C70–140Drying, °C, h1404–6 h
Grupa Azoty Tarfuse POM 3D FilamentGrupa Azoty
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Grupa Azoty, Preliminary Technical Data Sheet Tarfuse POM 3D Filament9 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile modulus XY | 1870 MPaMechanical Properties: Tensile E-modulus, XY (flat) | printed specimen, ISO 527As the sheet prints it: ISO 527-1,-2, 1 mm/minprint settingsPrinted flat (XY); tested at 23 °C; print parameters as recommended in the TDS | in the median |
| Tensile strength (yield or break not stated) XY | 50 MPaMechanical Properties: Tensile strength, XY (flat) | printed specimen, ISO 527As the sheet prints it: ISO 527-1,-2, 50 mm/minprint settingsPrinted flat (XY); tested at 23 °C; print parameters as recommended in the TDS | in the median |
| Elongation at break XY | 11 %Mechanical Properties: Elongation at break, XY (flat) | printed specimen, ISO 527As the sheet prints it: ISO 527-1,-2, 50 mm/minprint settingsPrinted flat (XY); tested at 23 °C; print parameters as recommended in the TDS | in the median |
| Glass transition temperature | -50 °CPhysical Properties: Glass transition temperature | ISO 11357As the sheet prints it: ISO 11357-1-3, DSC 10 °C/min | in the median |
| Melting temperature | 165-170 °CPhysical Properties: Melting temperature | ISO 11357As the sheet prints it: ISO 11357-1-3, DSC 10 °C/min | |
| Crystallization temperature | 140 °Cp. 2: Crystalization temperature; DSC | ISO 11357As the sheet prints it: ISO 11357-1-3; rate=10°C/min | |
| Density | 1,42 g/cm3 g/cm³Physical Properties: Density | ISO 1183 | |
| Water absorption | 0,2 %p. 2: Humidity absorption | ISO 62after moisture conditioning23°C/50%RH | |
| Melt volume-flow rate | 2,5 cm3/10minp. 2: Melt volume-flow rate MVR | ISO 1133As the sheet prints it: ISO 1133; 275°C/5 kg | |
Print settings
- Nozzle
- 210–240 °Cown data sheet
- Bed
- 100–130 °Cown data sheet
- Heated chamber
- 70–140 °Cown data sheet
- Drying
- 140 °C for 4–6 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 210-240 °C; Bed 100-130 °C; Chamber 70-140 °C (build chamber temperature); Drying 140 °C, 4-6 h (hot air dryer)Grupa Azoty, Preliminary Technical Data Sheet Tarfuse POM 3D Filamentp. 2: Recommended print processing parameters
Price
121 CAD/kgits one regular price in the sample
1 listing
- filamentworld.de: 121 CAD/kgTarfuse - POM Filament - Natur - 1.75 mm - 0,5 kg (SKU POM175XNAT)in its price; filamentworld.de (European storefront) lists 44.9 EUR including 19% VAT for 0.5 kg: 75.5 EUR/kg before VAT, × 1.6084 CAD per EUR (Bank of Canada, 29 Sep 2026). Used only where no Canadian shop in the sample sells the product. Shipping, duty and Canadian stock are not included.; seen 7 Oct 2026
Its 2 documents
What the maker says (3)
- Good for
Tarfuse® POM is designed for printing functional technical parts, due to the material features dedicated to printing parts up to 100mm.
Grupa Azoty, Preliminary Technical Data Sheet Tarfuse POM 3D Filamentp. 1 - Benefits
Tarfuse® POM is made of polyacetal copolymer, characterized by high mechanical strength, excellent tribological parameters.
Grupa Azoty, Preliminary Technical Data Sheet Tarfuse POM 3D Filamentp. 1 - Moisture sensitivity
To ensure good print quality, it is recommended to dry in a hot air dryer for 4 to 6 hours in 140°C.
Grupa Azoty, Preliminary Technical Data Sheet Tarfuse POM 3D Filamentp. 1
Fabru Polyoxymethylen (POM)Strength XY, MPa43Modulus XY, GPa1.05HDT 0.45, °C100HDT 1.8, °C—Price, CAD/kg—Nozzle, °C190–210Bed, °C120–150Chamber, °C—Drying, °C, h804 h
Fabru Polyoxymethylen (POM)Fabru
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Fabru, Polyoxymethylen (POM)9 values | |||
| Tensile modulus orientation not stated | 1050 MPap. 1: Tensile modulus (ISO 178) | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile yield strength orientation not stated | 43 MPap. 1: Yield stress (ISO 527-1/-2) | ISO 527As the sheet prints it: ISO 527-1/-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 50 %p. 1: Elongation at break (ISO 527-1/-2) | ISO 527As the sheet prints it: ISO 527-1/-2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at yield orientation not stated | 30 %p. 1: Elongation at yield (ISO 527-1/-2) | ISO 527As the sheet prints it: ISO 527-1/-2 | listed under other properties |
| HDT at 0.45 MPa | 100 °Cp. 1: Heat deflection temperature | ISO 75As the sheet prints it: 0.45 MPa (ISO 75-1/-2) | not in the median: set apart (never used to pass), test bar not described as printed |
| Vicat softening temperature | 116 °Cp. 1: Vicat softening temperature A | no standard stated | |
| Density | 1.34 g/cm3p. 1: Density (ISO 1183) | ISO 1183 | |
| Melt mass-flow rate | 2 g/10minp. 1: MFR (ISO 1133) | ISO 1133 | |
| Mould shrinkage orientation not stated | 0.95 %p. 1: Shrinkage (ISO 294-4) | ISO 294As the sheet prints it: ISO 294-4 | |
Print settings
- Nozzle
- 190–210 °Cown data sheet
- Bed
- 120–150 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 80 °C for 4 hown data sheet
- Hardened nozzle
- not stated
Its 2 print profiles, in the documents' words
- Nozzle 190-210°C; Bed 120-150°CFabru, purefil POM Filament | Fabru GmbHRecommended printing settings
- Nozzle 190-210 °C; Bed 120-150°C; Drying 80°C; Drying time 2-4hFabru, Polyoxymethylen (POM)p. 1: Printing temperature
Price
Not in the price sample.
Its 3 documents
What the maker says (16)
- Good for
POM filament is therefore one of the preferred construction materials, e.g. B. for snap connections and gears.
Fabru, Polyoxymethylen (POM)p. 1 - Good for
optimal for snap connections
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
It is one of the typical technical thermoplastics with good mechanical properties and high dimensional stability as well as excellent sliding and wear behavior.
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
Due to its high crystallinity, POM filament has good resistance to numerous chemicals.
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
They are resistant to diluted acids (pH > 4) as well as diluted alkalis, aliphatic, aromatic and halogenated hydrocarbons, oils and alcohols.
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
Excellent sliding and abrasion behavior
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
High resilience
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
relatively high temperature resistance
Fabru, Polyoxymethylen (POM)p. 1 - Benefits
High toughness down to -40°C
Fabru, Polyoxymethylen (POM)p. 1 - Pitfalls and limitations
They are not resistant to concentrated acids and hydrofluoric acid as well as oxidizing agents.
Fabru, Polyoxymethylen (POM)p. 1 - Pitfalls and limitations
The weather resistance is not good.
Fabru, Polyoxymethylen (POM)p. 1 - Pitfalls and limitations
narrow temperature range for processing
Fabru, Polyoxymethylen (POM)p. 1 - Warping and shrinkage
Shrinkage (ISO 294-4) 0.95 %
Fabru, Polyoxymethylen (POM)p. 1 - Warping and shrinkage
relatively high shrinkage
Fabru, Polyoxymethylen (POM)p. 1 - Moisture sensitivity
POM has low moisture absorption and high gas density.
Fabru, Polyoxymethylen (POM)p. 1 - Odour and emissions
If the processing temperature is too high, formaldehyde is released
Fabru, Polyoxymethylen (POM)p. 1
Chemicals and environment (3)
- Application notes: described in words
Low-friction gears and snap-fits are proposed applications.
Fabru, purefil POM Filament | Fabru GmbHApplication - UV and outdoor: described in words
Low moisture uptake, but poor weathering durability is stated.
EnvironmentalFabru, purefil POM Filament | Fabru GmbHEnvironmental - Organic solvent resistance: described in words
Dilute acids above pH 4, dilute bases, oils and alcohols are described as resistant; concentrated acids, hydrofluoric acid and oxidizers are not. Exposure duration and temperature are unspecified.
Chemical exposureFabru, purefil POM Filament | Fabru GmbHChemical exposure
No product matches "".
Not published by any product: tensile strength (Z) and notched impact.
Values are for the colour each sheet tested; pigment can change them.
Reference specimens and studies
A resin or study specimen, not a product you can buy.
DuPont Delrin 100P NC010 (POM homopolymer resin)Strength XY, MPa—Modulus XY, GPa—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C—Bed, °C—Chamber, °C—Drying, °C, h—
DuPont Delrin 100P NC010 (POM homopolymer resin)DuPont
A resin or study reference, not a product you can buy.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| DuPont, Product Information Delrin 100P NC0109 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile modulus orientation not stated | 2900 MPaMechanical: Tensile Modulus | ISO 527 | not in the median: measured on a moulded bar |
| Tensile yield strength orientation not stated | 70 MPaMechanical: Yield Stress | ISO 527 | not in the median: measured on a moulded bar |
| Elongation at break orientation not stated | 65 %Mechanical: Strain at Break, 50mm/min | ISO 527As the sheet prints it: ISO 527, 50 mm/min | not in the median: measured on a moulded bar |
| Flexural modulus orientation not stated | 2600 MPaMechanical: Flexural Modulus | ISO 178 | not in the median: measured on a moulded bar |
| HDT at 0.45 MPa | 160 °CThermal: Deflection Temperature 0.45MPa | ISO 75As the sheet prints it: ISO 75-1/-2, 0.45 MPa | not in the median: measured on a moulded bar |
| HDT at 1.8 MPa | 93 °CThermal: Deflection Temperature 1.80MPa | ISO 75As the sheet prints it: ISO 75-1/-2, 1.80 MPa | not in the median: measured on a moulded bar |
| Vicat softening temperature | 160 °CThermal: Vicat Softening Temperature | ISO 306As the sheet prints it: ISO 306, 50 N | |
| Melting temperature | 178 °CThermal: Melting Temperature | ISO 11357As the sheet prints it: ISO 11357-1/-3, 10 °C/min | |
| Density | 1.42 g/cm3 (1420 kg/m3) g/cm³Other: Density | ISO 1183 | |
Print settings
No print settings on file for this product.