PPS-CF
7 products from 7 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
7 products
Key
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- from the Bambu Lab Filament Guide
- Izod where no Charpy is published
- shared data sheet
- hardened nozzle
- not published
How the numbers are worked out
Bambu Lab PPS-CFStrength XY, MPa87Strength Z, MPa24Modulus XY, GPa8.23Charpy notched, kJ/m²6.2HDT 0.45, °C264HDT 1.8, °C235Price, CAD/kg221Nozzle, °C310–340Bed, °C100–120Chamber, °C60–90Drying, °C, h100–1408–12 h
Bambu Lab PPS-CFBambu Lab
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CF22 valuesUnless a row says otherwise: printed specimenas printedAll the specimens were not annealed before testingprint settingsSpecimen Printing Conditions Subjects Data Nozzle Temperature 320 °C Bed Temperature 110 °C Printing Speed 60mm/s InfillDensity 100% *All the specimens were printed at the following settings: Printer = X1E, Chamber Temperature = 60 °C, Nozzle Temperature = 320 °C, Printing Speed = 60 mm/s, Bed Temperature = 110 °C, InfillDensity = 100%. If higher chamber temperature and nozzl | |||
| Tensile modulus XY | 8230 ± 270 MPap. 2: Young's Modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 2850 ± 160 MPap. 2: Young's Modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 87 ± 5 MPap. 2: Tensile Strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 24 ± 3 MPap. 2: Tensile Strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 1.2 ± 0.4 %p. 2: Breaking Elongation Rate (X-Y) | ISO 527, GB/T 1040 | in the median |
| Elongation at break Z | 0.7 ± 0.3 %p. 2: Breaking Elongation Rate (Z) | ISO 527, GB/T 1040 | in the median |
| Flexural modulus XY | 7160 ± 280 MPap. 2: Bending Modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 2460 ± 190 MPap. 2: Bending Modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 142 ± 5 MPap. 2: Bending Strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 36 ± 4 MPap. 2: Bending Strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 27.8 ± 2.3 kJ/m²;p. 2: Impact Strength (X-Y) — unnotched | ISO 179, GB/T 1043 | not in the median: unnotched |
| Charpy impact strength XY | 6.2 ± 1.6 kJ/m²p. 2: Impact Strength (X-Y) — notched | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength Z | 2.8 ± 0.4 kJ/m²p. 2: Impact Strength (Z) | ISO 179, GB/T 1043 | not in the median: notch not stated |
| HDT at 0.45 MPa | 264 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 0.45 MPa | in the median |
| HDT at 1.8 MPa | 235 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 1.8 MPa | in the median |
| Glass transition temperature | 100 °Cp. 2: Glass Transition Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | in the median |
| Vicat softening temperature | 268 °Cp. 2: Vicat Softening Temperature | ISO 306, GB/T 1633 | |
| Melting temperature | 284 °Cp. 2: Melting Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Crystallization temperature | 214 °Cp. 2: Crystallization Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Density | 1.26 g/cm³p. 2: Density | specimen not stated, ISO 1183 | |
| Water absorption | 0.05 %p. 2: Saturated Water | no standard namedAs the sheet prints it: ter Absorption Rate 25 °C, 55% RH | |
| Melt mass-flow rate | 11.48 ± 1.23 g/10 minp. 2: Melt Index | specimen not stated, no standard namedAs the sheet prints it: 320 °C, 2.16 kg | |
Print settings
- Nozzle
- 310–340 °Cown data sheet
- Bed
- 100–120 °Cown data sheet
- Heated chamber
- 60–90 °Cown data sheet
- Drying
- 100–140 °C for 8–12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 310 -340 °C; Bed 100 -120 °C; Chamber 60 - 90 °C; Drying 100 -140 °C,8-12 hBambu Lab, Bambu Filament Technical Data Sheet - PPS-CFRecommended printing settings
Price
221 CAD/kgthe median of its 2 regular prices in the sample
2 listings
- Bambu Lab Canada: 221 CAD/kgPPS-CF - Black (76100) / Filament with spool / 0.75kgin its price; seen 10 Sep 2026
- 3D Printing Canada: 221 CAD/kgBlack - Bambu Lab PPS-CF Filament - 1.75mm, 0.75kg / Default Titlein its price; seen 10 Sep 2026
Its 2 documents
What the maker says (4)
- Benefits
The combination of PPS resin and carbon fiber gives PPS-CF exceptional properties, including excellent resistance to solvents, corrosion, heat, and flames.
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFp. 1 - Benefits
Additionally, it offers superior strength, stiffness, and dimensional stability, making it a specialized engineering plastic that meets the demands of unique and challenging applications.
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFp. 1 - Odour and emissions
Odor Odorless
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFp. 3 - Printing advice
If higher chamber temperature and nozzle temperature were used (i.g., 90 °C and 335 °C), higher mechanical properties would be obtained, especially the Z-direction's.
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFp. 3
Specimen preparation (1)
All the specimens were not annealed before testing
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFTest specimen preparation
Chemicals and environment (7)
- Water solubility: insoluble
Insoluble in water
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFSolubility - Acid resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFResistance to Acid - Alkali resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFResistance to Alkali - Organic solvent resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFResistance to Organic Solvent - Oil and grease resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFResistance to Oil and Grease - Flammability: self-extinguishing
Self-extinguishing when away from fire; flame-retardant
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFFlammability - Post-processing: described in words
the suggested annealing temperature of models printed with Bambu PPS-CF is 180 to 220 °C, and the time is 6 to 12 hours.
Bambu Lab, Bambu Filament Technical Data Sheet - PPS-CFp. 3: Annealing note
Polymaker FIBERON PPS CF10Strength XY, MPa59.4Strength Z, MPa32Modulus XY, GPa5.45Charpy notched, kJ/m²5.3HDT 0.45, °C253HDT 1.8, °C133Price, CAD/kg198Nozzle, °C310–350Bed, °C80–90Chamber, °CnoneDrying, °C, h10010 h
Polymaker FIBERON PPS CF10Polymaker
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Polymaker, FIBERON PPS CF1022 valuesUnless a row says otherwise:annealed at 125 °C for 16 hAll specimens were annealed at 125°C for 16h | |||
| Tensile modulus XY | 5446.7 ± 149.0 MPap. 1: Young’s modulus (X-Y) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Tensile modulus Z | 2790.0 ± 152.6 MPap. 1: Young’s modulus (Z) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Tensile strength (yield or break not stated) XY | 59.4 ± 1.3 MPap. 1: Tensile strength (X-Y) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Tensile strength (yield or break not stated) Z | 32.0 ± 5.1 MPap. 1: Tensile strength (Z) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Elongation at break XY | 1.4 ± 0.1 %p. 1: Elongation at break (X-Y) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Elongation at break Z | 1.6 ± 0.2 %p. 1: Elongation at break (Z) | ISO 527, GB/T 1040print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Flexural modulus XY | 4646.9 ± 136.9 MPap. 1: Bending modulus (X-Y) | ISO 178, GB/T 9341print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Flexural modulus Z | 2619.3 ± 155.3 MPap. 1: Bending modulus (Z) | ISO 178, GB/T 9341print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Flexural strength XY | 94.3 ± 1.9 MPap. 1: Bending strength (X-Y) | ISO 178, GB/T 9341print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Flexural strength Z | 30.0 ± 5.2 MPap. 1: Bending strength (Z) | ISO 178, GB/T 9341print settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Charpy impact strength XY | 5.3 ± 0.2 kJ/m2p. 1: Charpy impact strength (X-Y) notched | no standard statedprint settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | in the median |
| Charpy impact strength XY | 11.4 ± 0.7 kJ/m2p. 1: Charpy impact strength (X-Y)un-notched ISO 179, GB/T 1043 | ISO 179, GB/T 1043unnotchedprint settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | not in the median: unnotched |
| Charpy impact strength Z | 4.1 ± 1.3 kJ/m2p. 1: Charpy impact strength (Z) un-notched | no standard statedunnotchedprint settingsInfill 100%; Printing temperature 330-350 °C; Shell 2; Bed temperature 90 °C; Cooling fan OFF; Top & bottom layer 3 | not in the median: unnotched |
| HDT at 0.45 MPa | 252.5 °Cp. 1: Heat deflection temp. ISO 75 0.45MPa | ISO 75As the sheet prints it: 0.45MPa ISO 75 | in the median |
| HDT at 1.8 MPa | 133.0 °Cp. 1: Heat deflection temp. ISO 75 1.8MPa | ISO 75As the sheet prints it: 1.8MPa ISO 75 | in the median |
| Glass transition temperature | 97.7 °Cp. 1: Glass transition temp. DSC, 10°C/min | DSCtreatment not stated | in the median |
| Vicat softening temperature | 267.5 °Cp. 1: Vicat softening temp. ISO 306, GB/T 1633 | ISO 306, GB/T 1633 | |
| Melting temperature | 279.7 °Cp. 1: Melting temperature DSC, 10°C/min | DSCtreatment not stated | |
| Density | 1.29 g/cm3p. 1: Density ISO1183, GB/T1033 | ISO 1183, GB/T 1033treatment not stated | |
| Melt mass-flow rate | 26.2 g/10minp. 1: Melt index 300°C, 2.16 kg | no standard namedAs the sheet prints it: 300°C 2.16 kg | |
| Surface resistivity | 10^12 Ωtranscription correctedp. 1: Surface Resistivity (Ω) ANSI ESD S11.11 OL | no standard namedAs the sheet prints it: Ω ANSI ESD S11.11 OL | |
| Fibre content | PPS-CF10 %p. 1: Fibre content | no standard statedtreatment not stated | |
Print settings
- Nozzle
- 310–350 °Cown data sheet
- Bed
- 80–90 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 100 °C for 10 hown data sheet
- Hardened nozzle
- neededown data sheet
- Annealing
- 125 °C for 16 hown data sheet
Its print profile, in the documents' words
- Nozzle 310-350 °C; Bed 80-90 °C; Chamber Room temp.; Drying 100 °C/10HPolymaker, FIBERON PPS CF10p. 1: Recommended printing settings: Nozzle temperature; p. 1: Drying temp. and time
Price
198 CAD/kgits one regular price in the sample
1 listing
- Voxel Factory: 198 CAD/kgPolymaker Fiberon PPS-CF10 1.75mm 500g (SKU PMK-FBR-PPS-C10-500)in its price; seen 30 Sep 2026
Its 2 documents
What the maker says (5)
- Benefits
With exceptional mechanical strength, high heat resistance, chemical resistance, V0 flame retardancy, and moisture insensitivity, it's specifically designed for professionals operating in extreme conditions.
Polymaker, FIBERON PPS CF10p. 1 - Warping and shrinkage
Fiberon™ PPS-CF10 is a carbon fiber reinforced PPS (Polyphenylene sulfide) filament, with minimal warping during printing and no need for a heated chamber.
Polymaker, FIBERON PPS CF10p. 1 - Moisture sensitivity
Fiberon™ PPS-CF10 should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker, FIBERON PPS CF10p. 1 - Nozzle wear
Abrasion of the brass nozzle happens frequently when printing Fiberon™ PPS-CF10.
Polymaker, FIBERON PPS CF10p. 1 - Nozzle wear
A wear-resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with Fiberon™ PPS-CF10.
Polymaker, FIBERON PPS CF10p. 1
Chemicals and environment (1)
- Post-processing: described in words
Annealing temp. and time 125 °C/16H
Polymaker, FIBERON PPS CF10p. 1: Annealing temp. and time
Essentium PPS-CFStrength XY, MPa63Strength Z, MPa28.2Modulus XY, GPa7.46Charpy notched, kJ/m²3IzodHDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C330–400Bed, °C100–120Chamber, °CenclosedDrying, °C, h1203–8 h
Essentium PPS-CFEssentium
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheet24 valuesUnless a row says otherwise: printed specimenmoistureKeep vacuum sealed; dry at 120 °C for 3-8 h if >200 ppmprint settingsPrint Orientation XY | |||
| Tensile modulus XY | 7.46 (0.33) GPap. 1: Tensile modulus (XY) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Tensile modulus Z (ZX) | 2.72 (0.14) GPap. 1: Tensile modulus (ZX) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Tensile modulus ±45° raster | 4.55 (0.12) GPap. 1: Tensile modulus (45/45) | ISO 527As the sheet prints it: ISO 527-2 | not in the median: measured on a bar in another orientation |
| Tensile strength (yield or break not stated) XY | 63 (5.4) MPap. 1: Tensile strength (endpoint unspecified) (XY) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Tensile strength (yield or break not stated) Z (ZX) | 28.2 (4.4) MPap. 1: Tensile strength (endpoint unspecified) (ZX) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Tensile strength (yield or break not stated) ±45° raster | 44.7 (3.5) MPap. 1: Tensile strength (endpoint unspecified) (45/45) | ISO 527As the sheet prints it: ISO 527-2 | not in the median: measured on a bar in another orientation |
| Elongation at break XY | 2.2 (0.2) %p. 1: Elongation at break (XY) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Elongation at break Z (ZX) | 1.7 (0.3) %p. 1: Elongation at break (ZX) | ISO 527As the sheet prints it: ISO 527-2 | in the median |
| Elongation at break ±45° raster | 2.1 (0.2) %p. 1: Elongation at break (45/45) | ISO 527As the sheet prints it: ISO 527-2 | not in the median: measured on a bar in another orientation |
| Flexural modulus XY | 6.18 (0.49) GPap. 1: Flexural modulus (XY) | ISO 178 | in the median |
| Flexural modulus ±45° raster | 3.61 (0.32) GPap. 1: Flexural modulus (45/45) | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural modulus ZX | 2.31 (0.11) GPap. 1: Flexural modulus (ZX) | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 98.2 (9.5) MPap. 1: Flexural strength (XY) | ISO 178 | in the median |
| Flexural strength ±45° raster | 78.3 (3.9) MPap. 1: Flexural strength (45/45) | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural strength ZX | 38.7 (2) MPap. 1: Flexural strength (ZX) | ISO 178 | not in the median: measured on a bar in another orientation |
| Izod impact strength XY | 3 (0.7) kJ/m²p. 1: Izod impact strength (XY) | ISO 180notched | in the median |
| Izod impact strength ±45° raster | 2.6 (0.6) kJ/m²p. 1: Izod impact strength (45/45) | ISO 180notched | not in the median: measured on a bar in another orientation |
| Izod impact strength ZX | 2.2 (0.8) kJ/m²p. 1: Izod impact strength (ZX) | ISO 180notched | not in the median: measured on a bar in another orientation |
| Glass transition temperature | 92 °Cp. 1: Glass Transition Temp | specimen not stated, ISO 11357print settings not stated | in the median |
| Melting temperature | 280 °Cp. 1: Melting Point | specimen not stated, ISO 11357print settings not stated | |
| Continuous service temperature | 220 °C at 20,000 hp. 1: Continuous Service Temp | moulded bar (resin supplier's value), IEC 60216As the sheet prints it: IEC 60216; 20,000 h | |
| Density | 1.5 g/cm³p. 1: Density | moulded bar (resin supplier's value), ISO 1183print settings not stated | |
| Water absorption | 0.06%p. 1: Equilibrium Water Absorption | moulded bar (resin supplier's value), ISO 62As the sheet prints it: ISO 62; equilibrium at 23 °C, 50% RH | |
| Fibre content | 15% carbon fiberp. 1: Fibre content | specimen not stated, no standard statedmoisture state not statedprint settings not stated | |
| Also named without a value: hdt, hdt. | |||
Print settings
- Nozzle
- 330–400 °Cown data sheet
- Bed
- 100–120 °Cown data sheet
- Heated chamber
- enclosure needed, no temperatureBambu Lab Filament Guide
- Drying
- optional: 120 °C for 3–8 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 330-400 °C; Bed 100-120 °C; Drying If moisture >200 ppm: 120 °C for 3-8 hEssentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2: Recommended FFF Print Settings and Material Handling
Price
Not in the price sample.
Its 2 documents
What the maker says (8)
- Good for
Expanded foam mold tooling
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Good for
Railway parts
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Benefits
Excellent chemical and solvent resistance
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Benefits
Lower cost compared to PEEK
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Benefits
Inherently flame retardant
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Moisture sensitivity
Essentium PPS-CF is a slightly hygroscopic thermoplastic and will absorb small amounts of moisture from humid air.
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Moisture sensitivity
PPS-CF filament should always be fed to the printer in a dry container and stored in a dry cabinet to minimize absorbed moisture.
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2 - Printing advice
Essentium recommends printing PPS-CF on a G14 phenolic build sheet with a thin layer of Magigoo® HT applied to the surface to facilitate the removal of parts.
Essentium / Nexa3D, Essentium PPS-CF Technical Data Sheetp. 2
Chemicals and environment (3)
- Application notes: described in words
Tooling, chemical/solvent-resistant uses, and high-temperature applications
Published applicationsEssentium / Nexa3D, Essentium PPS-CF Technical Data Sheetpp. 1-2: Published applications - Organic solvent resistance: described in words
Excellent resistance is a qualitative manufacturer claim; no exposure matrix supplied
Chemical and solvent resistanceEssentium / Nexa3D, Essentium PPS-CF Technical Data Sheetpp. 1-2: Chemical and solvent resistance - Moisture sensitivity: described in words
Slightly hygroscopic; keep vacuum sealed and dry if >200 ppm
Moisture handlingEssentium / Nexa3D, Essentium PPS-CF Technical Data Sheetpp. 1-2: Moisture handling
Flashforge PPS-CFStrength XY, MPa95Strength Z, MPa—Modulus XY, GPa8Charpy notched, kJ/m²7IzodHDT 0.45, °C245HDT 1.8, °C—Price, CAD/kg—Nozzle, °C300–350Bed, °C90–110Chamber, °C25–80Drying, °C, h120≥ 8 h
Flashforge PPS-CFFlashforge
Data sheet shared with SIDDAMENT PPS CF: their values are one table, recorded once.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Flashforge, Technical Data Sheet PPS-CF Filament16 valuesThe same values also in SIDDAMENT, Technical Data Sheet PPS CF Filament. | |||
| Tensile modulus XY | 8000-9000 Mpap. 1: Modulus of Elasticity (X-Y) ISO 527 Mpa | ISO 527print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Tensile strength (yield or break not stated) XY | 95-105 Mpap. 1: Tensile Strength (X-Y) ISO 527 Mpa | ISO 527print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Elongation at break XY | 4-6 %p. 1: Elongation at Break (X-Y) ISO 527 % | ISO 527print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Flexural modulus XY | 6000-6500 Mpap. 1: Bending Modulus (X-Y) ISO178 Mpa | ISO 178print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Flexural modulus Z | 2200-2260 Mpap. 1: Bending Modulus (Z) ISO178 Mpa | ISO 178print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Flexural strength XY | 125-135 Mpap. 1: Bending Strength (X-Y) ISO178 Mpa | ISO 178print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Flexural strength Z | 50-52 Mpap. 1: Bending Strength (Z) ISO178 Mpa | ISO 178print settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Izod impact strength XY | 7-8 KJ/m2p. 1: Izod Impact Strength (X-Y) ISO180 KJ/m2 | ISO 180notchedprint settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | in the median |
| Izod impact strength Z | 2.5-3 KJ/m2p. 2: Izod Impact Strength (Z) ISO180 KJ/m2 | ISO 180notchedprint settingsTest Equipment Guider 3 Ultra (Flashforge); Nozzle Diameter 0.4mm; Nozzle Temperature 320 °C; Printing Speed 150mm/s; Wall Thickness 0.4mm; Infill 100% | not in the median: measured on a bar in another orientation |
| HDT at 0.45 MPa | 245 ℃p. 2: HDT@ 0.455 MPa (66 psi) ISO75 ℃ | ISO 75As the sheet prints it: 0.455 MPa 66 psi ISO75 | in the median |
| Continuous service temperature | 220 ℃p. 2: Continuous Service Temperature IEC 60216 ℃ | IEC 60216 | |
| Density | 1.30-1.32 g/cm³p. 1: Density ISO 1183 g/cm³ | ISO 1183 | |
| Water absorption | 0.1 %p. 1: Water Absorption (23℃/24h) ISO 62 % | ISO 62As the sheet prints it: 23℃/24h ISO 62 | |
| Melt mass-flow rate | 50-60 g/10minp. 1: Melt Flow Rate (MFR) (316℃/5Kg) ISO 1133 g/10minalso in SIDDAMENT, Technical Data Sheet PPS CF Filament | ISO 1133As the sheet prints it: MFR 316℃/5Kg ISO 1133 | |
| Surface resistivity | 10^5 Ωtranscription correctedp. 2: Surface Resistance IEC 60093 Ω | IEC 60093 | |
| Fibre content | 10% carbon fiberp. 1: Fibre content | no standard stated | |
| SIDDAMENT, Technical Data Sheet PPS CF Filament1 value | |||
| Flexural modulus XY | 8000~9000 Mpap. 1: Flexural Modulus(X-Y) | ISO 527 | not in the median: another value of this product is in it |
Print settings
- Nozzle
- 300–350 °Cown data sheet
- Bed
- 90–110 °Cown data sheet
- Heated chamber
- 25–80 °Cown data sheet
- Drying
- optional: 120 °C for ≥ 8 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 300~350℃ (320℃ recommended); Bed 90~110℃ (100℃ recommended); Chamber Room temperature~80℃; Drying In case the filament has become wet, it should be dried before being used; Using a hot dry air oven at 120℃ for at least 8 hours is recommendedFlashforge, Technical Data Sheet PPS-CF Filamentp. 2: Recommended printing settings: Nozzle Temperature; p. 2: Ambient Temperature for Printing; p. 3: Drying note; p. 2: Nozzle Diameter (recommended printing settings)
Price
Not in the price sample.
Its 3 documents
What the maker says (7)
- Benefits
It is a modified polyphenylene sulfide (PPS) containing 10% carbon fiber, offering high-temperature resistance, low moisture absorption, chemical resistance, and flame retardancy, with the ability to be printable on non-heated chamber FFF 3D printers.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 1 - Benefits
Models printed with PPS-CF exhibit excellent rigidity and strength and allow continuous use up to 220℃, with a heat deflection temperature of up to 245°C. Consequently, its dimensional stability and electrical properties are minimally affected by humidity and temperature variations, and it also possesses flame retardant properties.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 1 - Benefits
High rigidity/High strength/High-temperature resistance/Flame retardancy
Flashforge, Technical Data Sheet PPS-CF Filamentp. 1 - Nozzle wear
Nozzle & Gear Material Hardened steel
Flashforge, Technical Data Sheet PPS-CF Filamentp. 2 - Supports and removal
Otherwise, the support structure can be bonded to the model, which will make the support hard to remove.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 3 - Supports and removal
If PPS-CF is used as the support material for itself, please remove the support structure as soon as the model cools down.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 3 - Printing advice
After the printing process, it is recommended to dry the model in the oven at 80-100°C for 1-3 hours to increase the strength of the model.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 3
Chemicals and environment (1)
- Post-processing: described in words
After the printing process, it is recommended to dry the model in the oven at 80-100°C for 1-3 hours to increase the strength of the model.
Flashforge, Technical Data Sheet PPS-CF Filamentp. 3: Post-processing note
SIDDAMENT PPS CFStrength XY, MPa95Strength Z, MPa—Modulus XY, GPa8Charpy notched, kJ/m²7IzodHDT 0.45, °C245HDT 1.8, °C—Price, CAD/kg—Nozzle, °C300–350Bed, °C90–110Chamber, °C25–80Drying, °C, h120≥ 8 h
SIDDAMENT PPS CFSIDDAMENT
Data sheet shared with Flashforge PPS-CF: their values are one table, recorded once.
Published values
No value is on file for this product.
Print settings
- Nozzle
- 300–350 °Cown data sheet
- Bed
- 90–110 °Cown data sheet
- Heated chamber
- 25–80 °Cown data sheet
- Drying
- 120 °C for ≥ 8 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 300~350℃(Recommend 320℃); Bed 90~110℃( Recommend 100℃); Chamber Room Temperature ~80℃; Drying 120°C for at least 8 hoursSIDDAMENT, Technical Data Sheet PPS CF Filamentp. 2: Nozzle Temperature, Bed Temperature, Printing Environmental Temperature
Price
Not in the price sample.
Its 2 documents
What the maker says (3)
- Benefits
It has high temperature resistance, low moisture absorption, chemical resistance and flame retardancy, and can be used on 3D printers in non-heated chambers.
SIDDAMENT, Technical Data Sheet PPS CF Filamentp. 1 - Benefits
High stiffness/high strength/high temperature resistance/flame retardant
SIDDAMENT, Technical Data Sheet PPS CF Filamentp. 1 - Nozzle wear
Nozzle and gear material High strength steel
SIDDAMENT, Technical Data Sheet PPS CF Filamentp. 2
Chemicals and environment (1)
- Post-processing: described in words
After the model is printed, it is recommended to dry it in an oven at a temperature of 80 ~100°C for 1 ~ 3 hours to improve the strength of the model.
SIDDAMENT, Technical Data Sheet PPS CF Filamentp. 3: Post-processing note
Raise3D Industrial PPS CFStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C251HDT 1.8, °C132Price, CAD/kg—Nozzle, °C310–340Bed, °C100–120Chamber, °CnoneDrying, °C, h100–1408–12 h
Raise3D Industrial PPS CFRaise3D
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Raise3D, Raise3D Industrial PPS CF Technical Data Sheet31 valuesUnless a row says otherwise: printed specimenafter moisture conditioningConditioned | |||
| Tensile modulus XY | 5500 ± 150 MPap. 1: Young’s modulus (MPa) (5500 ± 150) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Tensile modulus XY | 4700 ± 280 MPap. 2: Young’s modulus (MPa) (XY) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile modulus Z (ZX) | 2600 ± 120 MPap. 2: Young’s modulus (MPa) (ZX) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile modulus ZX | 2800 ± 150 MPap. 1: Young’s modulus (MPa) (2800 ± 150) (Typical Value (ZX, Flat) column) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 60 ± 1.3 MPap. 1: Tensile strength (MPa) (60 ± 1.3) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 50 ± 2 MPap. 2: Tensile strength (MPa) (XY) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z (ZX) | 22 ± 4 MPap. 2: Tensile strength (MPa) (ZX) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) ZX | 32.0 ± 5.0 MPap. 1: Tensile strength (MPa) (32.0 ± 5.0) (Typical Value (ZX, Flat) column) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Elongation at break XY | 1.8 ± 0.1 %p. 1: Elongation at break (%) (1.8 ± 0.1) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Elongation at break XY | 1.2 ± 0.5 %p. 2: Elongation at break (%) (XY) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Elongation at break Z (ZX) | 1.1 ± 0.1 %p. 2: Elongation at break (%) (ZX) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealed | not in the median: measured after moisture conditioning |
| Elongation at break ZX | 1.9 ± 0.2 %p. 1: Elongation at break (%) (1.9 ± 0.2) (Typical Value (ZX, Flat) column) | ISO 527As the sheet prints it: ISO 527; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 4600 ± 140 MPap. 1: Bending modulus (MPa) (4600 ± 140) | ISO 178As the sheet prints it: ISO 178; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 5000 ± 200 MPap. 2: Bending modulus (MPa) (XY) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural modulus ZX | 2600 ± 150 MPap. 1: Bending modulus (MPa) (2600 ± 150) (Typical Value (ZX, Flat) column) | ISO 178As the sheet prints it: ISO 178; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100% | not in the median: measured after moisture conditioning |
| Flexural modulus ZX | 2500 ± 320 MPap. 2: Bending modulus (MPa) (ZX) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural strength XY | 95 ± 2 MPap. 2: Bending strength (MPa) (XY; annealed at 125 ºC for 16h; Mechanical Properties (Conditioned, after annealed) / Typical Value (XY, Flat) | (ZX, Flat); 95 ± 2 MPa) | ISO 178annealed at 125 °C for 16 hannealed at 125 ºC for 16h | not in the median: measured after moisture conditioning |
| Flexural strength XY | 100 ± 4.0 MPap. 2: Bending strength (MPa) (XY; before annealed; Mechanical Properties (Conditioned, before annealed) / Typical Value (XY, Flat); 100 ± 4.0 MPa) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural strength ZX | 30.0 ± 5 MPap. 2: Bending strength (MPa) (XY; annealed at 125 ºC for 16h; Mechanical Properties (Conditioned, after annealed) / Typical Value (XY, Flat) | (ZX, Flat); 30.0 ± 5 MPa) | ISO 178annealed at 125 °C for 16 hannealed at 125 ºC for 16h | not in the median: measured after moisture conditioning |
| Flexural strength ZX | 52 ± 4.0 MPap. 2: Bending strength (MPa) (ZX; before annealed; Mechanical Properties (Conditioned, before annealed) / Typical Value (ZX, Upright); 52 ± 4.0 MPa) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 11.4 ± 0.7 (Un-notched) kJ/m²p. 2: Charpy impact strength (kJ/m²) (XY; annealed at 125 ºC for 16h; Mechanical Properties (Conditioned, after annealed); 11.4 ± 0.7 (Un-notched)) | ISO 179As the sheet prints it: ISO 179; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100%. | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 5 ± 0.4 kJ/m²p. 2: Charpy impact strength (kJ/m²) (XY; before annealed; Mechanical Properties (Conditioned, before annealed); 5 ± 0.4) | ISO 179As the sheet prints it: ISO 179; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealedprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100%. | not in the median: measured after moisture conditioning |
| Charpy impact strength ZX | 4.1± 1.3 (Un-notched) kJ/m²p. 2: Charpy impact strength (kJ/m²) (ZX, Flat; annealed at 125 ºC for 16h; Mechanical Properties (Conditioned, after annealed); 4.1± 1.3 (Un-notched)) (Typical Value (ZX, Flat) column) | ISO 179As the sheet prints it: ISO 179; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%annealed at 125 °C for 16 hannealed at 125 ºC for 16hprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100%. | not in the median: measured after moisture conditioning |
| Charpy impact strength ZX | 3 ± 0.8 kJ/m²p. 2: Charpy impact strength (kJ/m²) (ZX; before annealed; Mechanical Properties (Conditioned, before annealed); 3 ± 0.8) | ISO 179As the sheet prints it: ISO 179; nozzle temp=340 ºC; bed temp=90 ºC; infill=100%as printedbefore annealedprint settingsNozzle temp. = 340 ºC; Bed temp.= 90 ºC; Infill= 100%. | not in the median: measured after moisture conditioning |
| HDT | 260 °Cp. 1: Description | specimen not stated, no standard statedmoisture state not stated | not in the median: another value of this product is in it |
| HDT at 0.45 MPa | 251 °Cp. 2: Heat distortion temperature (°C) (ISO 75 @0.45 MPa) | ISO 75As the sheet prints it: ISO 75 @0.45 MPaannealed at 125 °C for 16 hannealed at 125 ºC for 16h | in the median |
| HDT at 1.8 MPa | 132 °Cp. 2: Heat distortion temperature (°C) (ISO 75 @1.8 MPa) | ISO 75As the sheet prints it: ISO 75 @1.8 MPaannealed at 125 °C for 16 hannealed at 125 ºC for 16h | in the median |
| Density | 1.29 g/cm³p. 1: Density | specimen not stated, ISO 1183, GB/T 1033moisture state not stated | |
| Water absorption | 0.23 %p. 1: Water absorption | specimen not stated, no standard statedmoisture state not stated | |
| Melt mass-flow rate | 28 g/10 minp. 2: Melt flow index (g/10 min) | specimen not stated, no standard namedAs the sheet prints it: 2.16 kg | |
| Fibre content | 10 wt.%p. 1: Fibre content | specimen not stated, no standard statedmoisture state not stated | |
Print settings
- Nozzle
- 310–340 °CBambu Lab Filament Guide
- Bed
- 100–120 °CBambu Lab Filament Guide
- Heated chamber
- not requiredown data sheet
- Drying
- 100–140 °C for 8–12 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
- Annealing
- 125 °C for 16 hown data sheet
Its print profile, in the documents' words
- Chamber non-heated printing camberRaise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1: Description (a non-heated printing chamber); p. 3: Note 1 (a wear-resistant nozzle). The nozzle and bed temperatures of its p. 2 footnote are the specimens' print conditions, which are not recorded as guidance.
Price
Not in the price sample.
Its 2 documents
What the maker says (7)
- Benefits
It stands out with its peerless heat resistance (HDT 260 °C) and chemical stability against the corrosion of various acids, alkalis, and organic solvents.
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1 - Benefits
Additionally, PPS CF possesses good flame-retardant property and is certified to UL94 V0 level.
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1 - Benefits
In terms of mechanical performance, final parts and components printed from PPS CF exhibits metal-like strength and rigidity, along with excellent long-term dimensional stability and very low moisture absorption.
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1 - Warping and shrinkage
More importantly, thanks to the specially optimized carbon fiber distribution and length, PPS CF is well compatible with non-heated printing camber and high-speed printing (L1, 150 mm/s, or faster to L2) with lower warpage, good surface finishing and lower nozzle abrasion.
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1 - Odour and emissions
Odor / Almost odorless
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 1 - Moisture sensitivity
Industrial PPS CF should always be stored and used under dry conditions (relative humidity below 20%).
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 3 - Nozzle wear
A wear-resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with Industrial PPS CF.
Raise3D, Raise3D Industrial PPS CF Technical Data Sheetp. 3
LEHVOSS LUVOCOM 3F PPS CF 9938 BKStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C310–340Bed, °C≥ 50Chamber, °CnoneDrying, °C, h100–1402–4 h
LEHVOSS LUVOCOM 3F PPS CF 9938 BKLEHVOSS
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| 3D4Makers, LUVOCOM 3F PPS CF 9938 BK11 values | |||
| Tensile modulus orientation not stated | 11 GPap. 1: Modulus of elasticity dry, @1 mm/min ISO 527 MPTS ISO 3167 A GPa | ISO 527, ISO 3167As the sheet prints it: 1 mm/min MPTS A ISO 527 ISO 3167 | not in the median: measured on a moulded bar |
| Tensile strength (yield or break not stated) orientation not stated | 120 MPap. 1: Tensile strength dry, @50 mm/min ISO 527 MPTS ISO 3167 A MPa | ISO 527, ISO 3167As the sheet prints it: 50 mm/min MPTS A ISO 527 ISO 3167 | not in the median: measured on a moulded bar |
| Tensile strain at strength orientation not stated | 1,6 %p. 1: Elongation at maximum force dry, @50 mm/min ISO 527 MPTS ISO 3167 A % | ISO 527, ISO 3167As the sheet prints it: 50 mm/min MPTS A ISO 527 ISO 3167 | listed under other properties |
| Flexural modulus orientation not stated | 9 GPap. 1: Flexural modulus dry, @2 mm/min ISO 178 MPTS ISO 3167 A GPa | ISO 178, ISO 3167As the sheet prints it: 2 mm/min MPTS A ISO 178 ISO 3167 | not in the median: measured on a moulded bar |
| Flexural strength orientation not stated | 170 MPap. 1: Flexural strength dry, @10 mm/min ISO 178 MPTS ISO 3167 A MPa | ISO 178, ISO 3167As the sheet prints it: 10 mm/min MPTS A ISO 178 ISO 3167 | not in the median: measured on a moulded bar |
| Charpy impact strength | 22 kJ/m²p. 1: Charpy impact strength dry ISO 179 1eU 80x10x4mm kJ/m² | ISO 179As the sheet prints it: 1eU 80x10x4mm ISO 179 | not in the median: unnotched |
| Melting temperature | held back: the sheet's unit or table layout is unclearheld backp. 2: Melt temperature °C | no standard stated | |
| Continuous service temperature | 220 °Cp. 1: Continuous service temperature 20.000 h IEC 60216 MPTS ISO 3167 A °C | IEC 60216, ISO 3167As the sheet prints it: 20.000 h MPTS A IEC 60216 ISO 3167 | |
| Density | 1,51 g/cm³p. 1: Specific gravity ISO 1183-3 g/cm³ | ISO 1183As the sheet prints it: ISO 1183-3 | |
| Water absorption | 0,05 %p. 1: Water absorption 23°C / 24h ISO 62 MPTS ISO 3167 A % | ISO 62, ISO 3167As the sheet prints it: 23°C / 24h MPTS A ISO 62 ISO 3167 | |
| Surface resistivity | 10⁶ Ωp. 1: Surface resistance ROB DIN IEC 60093 Ronde 60x4mm Ω | IEC 60093As the sheet prints it: 60x4mm IEC 60093 | |
| LEHVOSS, LUVOCOM-3F | LEHVOSS Compounds1 value | |||
| Fibre content | 15 %p. 1: carbon fibers | no standard stated | |
Print settings
- Nozzle
- 310–340 °Cown data sheet
- Bed
- at least 50 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 100–140 °C for 2–4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 310 - 340 °C; Bed > 50 °C; Drying 100 - 140 °C, 2 - 4 h3D4Makers, LUVOCOM 3F PPS CF 9938 BKp. 2: Recommended printing settings; p. 2: nozzle material; p. 2: Dehumidifying dryer
- Chamber Unser Material braucht keinen temperierten Bauraum für den Druckvorgang.LEHVOSS, LUVOCOM 3F (LEHVOSS brochure, German)p. 1: Bauraum
Price
Not in the price sample.
Its 4 documents
What the maker says (4)
- Benefits
Electrically conductive, suitable for continuous discharging of statically-generated electricity.
3D4Makers, LUVOCOM 3F PPS CF 9938 BKp. 1 - Benefits
High continuous-use and heat-distortion temperatures.
3D4Makers, LUVOCOM 3F PPS CF 9938 BKp. 1 - Benefits
Strong, stiff parts.
3D4Makers, LUVOCOM 3F PPS CF 9938 BKp. 1 - Nozzle wear
nozzle material: abbrasion resistant
3D4Makers, LUVOCOM 3F PPS CF 9938 BKp. 2
No product matches "".
Values are for the colour each sheet tested; pigment can change them.