PLA-NF
3 products from 3 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
3 products
Key
- set apart: test bar not described as printed, or no stated load
- not published
How the numbers are worked out
Extrudr FLAXStrength XY, MPa43Modulus XY, GPa3.8Charpy notched, kJ/m²3HDT 0.45, °C55HDT 1.8, °C52Nozzle, °C180–240Bed, °C20–60Chamber, °CnoneDrying, °C, h504 h
Extrudr FLAXExtrudr
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Extrudr, FLAX Filament – Made from Renewable Raw Materials | Extrudr18 valuesUnless a row says otherwise: specimen not stated; its document points to a moulded or resin bar | |||
| Tensile modulus orientation not stated | 3800 MPap. 1: Tensile modulus (Young's modulus) | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile yield strength orientation not stated | 43 MPap. 1: Tensile strength at yield | ISO 527As the sheet prints it: ISO 527-1 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 43 MPap. 1: Tensile stress at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 22.3 %p. 1: Elongation at break | ISO 527As the sheet prints it: ISO 527-1 | not in the median: the only value of its test, shown as published |
| Flexural modulus orientation not stated | 3400 MPap. 1: Flexural modulus | ISO 178 | not in the median: the only value of its test, shown as published |
| Flexural strength orientation not stated | 30 MPap. 1: Flexural strength | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength orientation not stated | 3 kJ/m²p. 1: Charpy notched impact strength (+23°C) | ISO 179As the sheet prints it: ISO 179-1eA | not in the median: the only value of its test, shown as published |
| Charpy impact strength orientation not stated | 2.5 kJ/m²p. 1: Charpy notched impact strength (-30°C) | ISO 179As the sheet prints it: ISO 179-1eA | not in the median: tested below room temperature |
| Charpy impact strength orientation not stated | 14 kJ/m²p. 1: Charpy unnotched impact strength (+23°C) | ISO 179As the sheet prints it: ISO 179-1eU | not in the median: unnotched |
| Charpy impact strength orientation not stated | 12 kJ/m²p. 1: Charpy unnotched impact strength (-30°C) | ISO 179As the sheet prints it: ISO 179-1eU | not in the median: unnotched |
| HDT at 0.45 MPa | 55 °Cp. 1: Heat deflection temp. (HDT/B) — 0.45 MPa | ISO 75As the sheet prints it: ISO 75-1; 0.45 MPa | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 1.8 MPa | 52 °Cp. 1: Heat deflection temp. (HDT/A) — 1.8 MPa | ISO 75As the sheet prints it: ISO 75-1; 1.8 MPa | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 60 °Cp. 1: Glass transition temp. (Tg) | specimen not stated, ISO 11357As the sheet prints it: ISO 11357-1 (DSC) | in the median |
| Melting temperature | 155 °Cp. 1: Melting point (Tm) | specimen not stated, ISO 3146As the sheet prints it: ISO 3146-C | |
| Decomposition temperature | 240 °Cp. 1: Thermal decomposition temp. | specimen not stated, no standard stated | |
| Water absorption | 1 %p. 1: Water absorption (saturation, 23°C) | specimen not stated, no standard namedAs the sheet prints it: state=saturation | |
| Melt volume-flow rate | 20 cm³/10 minp. 1: Melt volume rate (MVR) — 235°C/5.0 kg | specimen not stated, no standard namedAs the sheet prints it: temp/load=235°C/5.0 kg | |
| Mould shrinkage orientation not stated | 0.3–0.4 %p. 1: Mould shrinkage | specimen not stated, ISO 294As the sheet prints it: ISO 294-4 | |
| Extrudr, TECHNICAL DATA SHEET FLAX7 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile strength (yield or break not stated) | 43 MPap. 1: Tensile strength ISO 527 MPa | ISO 527 | not in the median: measured on a moulded bar |
| Elongation at break | 22.3 %p. 1: Elongation at break ISO 527 % | ISO 527 | not in the median: measured on a moulded bar |
| Flexural modulus | 3400 MPap. 1: Flexural modulus ISO 527 MPa | ISO 527 | not in the median: measured on a moulded bar |
| Flexural strength | 30 MPap. 1: Flexural strength ISO 527 MPa | ISO 527 | not in the median: measured on a moulded bar |
| Vicat softening temperature | 48 °Cp. 1: VICAT A (VST) ISO 306 °C | ISO 306 | |
| Density | 1.45 g/cm³p. 1: Density ISO 2781 g/cm³ | specimen not stated, ISO 2781 | |
| Melt mass-flow rate | 15 g/10minp. 1: MFR ISO 1133 g/10min | specimen not stated, ISO 1133 | |
Print settings
- Nozzle
- 180–240 °Cown data sheet
- Bed
- 20–60 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 50 °C for 4 hown data sheet
- Hardened nozzle
- not neededown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 180-240°C; Bed 20-60°CExtrudr, TECHNICAL DATA SHEET FLAXp. 1: Recommended printing settings; p. 1: Adhesive
- Nozzle 180–240 °C; Bed 20–60 °C; Drying Drying temperature 50 °C; Drying time 4 hExtrudr, FLAX Filament – Made from Renewable Raw Materials | Extrudrp. 1: Print Settings, Drying (drying only; p. 1: Surface preparation; p. 1: Recommended settings for printers with a 0.4 mm nozzle
Price
Not in the price sample.
Its 3 documents
What the maker says (7)
- Good for
The material has been developed for rapid prototyping applications.
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Benefits
Biodegradable (DIN EN ISO 14855)
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Benefits
Thanks to the added mineral filler, fast production speed is possible.
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Warping and shrinkage
Low warping
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Surface finish
Mineral-like surface
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Surface finish
At high temperatures and uniform printing speed, the surface becomes rough and resembles sandstone.
Extrudr, TECHNICAL DATA SHEET FLAXp. 1 - Nozzle wear
Hardened Nozzle no
Extrudr, TECHNICAL DATA SHEET FLAXp. 1
Nanovia PLA FlaxStrength XY, MPa37Modulus XY, GPa2.83Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Nozzle, °C200–230Bed, °C50–70Chamber, °C20Drying, °C, h504 h
Nanovia PLA FlaxNanovia
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanovia10 values | |||
| Tensile modulus XY | 2830 MPap. 1: Young’s modulus | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | in the median |
| Tensile modulus orientation not stated | 3100 MPap. 1: Young modulus’s (0° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins at 0°, along with the tension stress. | not in the median: another value of this product is in it |
| Tensile strength (yield or break not stated) XY | 37 MPap. 1: Ultimate strength (+45° / -45° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | in the median |
| Tensile strain at strength XY | 2.4 %p. 1: Elongation ultimate strength (+45° / -45° tab) | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins successively at 45° and -45° per layer. | listed under other properties |
| Tensile strain at strength orientation not stated | 2.5 %p. 1: Elongation ultimate strength | ISO 527As the sheet prints it: ISO 527-2/1Aprint settingsTest performed at 1mm/min on 3D printed test specimins at 0°, along with the tension stress. | listed under other properties |
| Hardness | 77 Shore Dp. 1: Hardness | no standard stated | in the median |
| HDT at 0.45 MPa | 80-90 °Cphysically implausiblep. 1: HDT B (0.45 MPa) | ASTM E2092As the sheet prints it: 0.45 MPa E2092 | not in the median: physically implausible as published |
| Glass transition temperature | 55 – 60 °Cp. 1: Tg | no standard stated | in the median |
| Density | 1,25 g/cm3p. 1: Density | ISO 1183 | |
| Melt mass-flow rate | 7 – 9 g / 10 minp. 1: Melt Flow rate (MFR) | ISO 1133 | |
Print settings
- Nozzle
- 200–230 °Cown data sheet
- Bed
- 50–70 °Cown data sheet
- Heated chamber
- 20 °Cown data sheet
- Drying
- optional: 50 °C for 4 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 200 – 230 °C; Bed 50 – 70 °C; Chamber 20 °C; Drying Dehydrate for 4h at 50°C prior to printing after prolonged exposure to humidity.Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1: Recommended printing settings; p. 1: Drying note; p. 1: Nozzle (minimal)
Price
Not in the price sample.
Its 2 documents
What the maker says (5)
- Good for
The organic look of this filament makes it ideal for decorative objects and toys.
Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1 - Benefits
Easy to print
Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1 - Benefits
Combining PLA’s ease of printing with flax fibers’ mechanical properties, Nanovia PLA Flax will allow you to create mechanical 3D prints with ease.
Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1 - Benefits
Biocourced and biodegradable
Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1 - Surface finish
This biosourced composite 3D filament, certified endocrine disruptor free, can be browned by varying the printing temperature up to 260 °C.
Nanovia, Nanovia PLA Flax : Flax fiber reinforced : Nanoviap. 1
Filamentive Hemp PLAStrength XY, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C55HDT 1.8, °C—Nozzle, °C185–215Bed, °C≤ 45Chamber, °C—Drying, °C, h—
Filamentive Hemp PLAFilamentive
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Filamentive, Hemp PLA Technical Data Sheet12 values | |||
| Tensile modulus orientation not stated | 3.5 GPap. 1: Tensile Modulus | ASTM D882As the sheet prints it: D 882 | not in the median: measured on film |
| Tensile yield strength orientation not stated | 60 MPap. 1: Tensile Yield Strength | ASTM D882As the sheet prints it: D 882 | not in the median: measured on film |
| Tensile break strength orientation not stated | 53 MPap. 1: Tensile Strength at Break | ASTM D882As the sheet prints it: D 882 | not in the median: measured on film |
| Elongation at break orientation not stated | 6%p. 1: Tensile Elongation | ASTM D882As the sheet prints it: D 882 | not in the median: measured on film |
| Flexural modulus orientation not stated | 3.8 MPaphysically implausiblep. 1: Flexural Modulus | ASTM D790As the sheet prints it: D 790 | not in the median: physically implausible as published |
| Flexural strength orientation not stated | 83 MPap. 1: Flexural Strength | ASTM D790As the sheet prints it: D 790 | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength orientation not stated | 16 J/mp. 1: Notched Izod Impact | ASTM D256As the sheet prints it: D 256 | not in the median: in J/m |
| HDT | 55 °Cp. 1: Heat Distortion Temperature | ASTM E2092As the sheet prints it: E 2092 | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 55–60 °Cp. 1: Glass Transition Temperature | ASTM D3418As the sheet prints it: D 3418 | in the median |
| Density | 1.24 g/cm3p. 1: Specific Gravity | ASTM D792As the sheet prints it: D 792 | |
| Melt mass-flow rate | 6 g/10minp. 1: Melt Flow Rate (210 °C, 2.16kg) | ASTM D1238As the sheet prints it: D 1238 | |
| Fibre content | 10% hemp byproductsp. 1: Description | no standard stated | |
Print settings
- Nozzle
- 185–215 °Cown data sheet
- Bed
- 45 °Cown data sheet
- Heated chamber
- not stated
- Drying
- not stated
- Hardened nozzle
- not neededown data sheet
Its print profile, in the documents' words
- Nozzle 200 ± 15°C; Bed ≤45°CFilamentive, Hemp Based PLA – Sustainable 3D Printing Filament - 1.75mm, 1 kg - Filamentivep. 1: Hardened nozzle; Printing temperature; Bed temperature
No product matches "".
Not published by any product: tensile strength (Z) and price.
Values are for the colour each sheet tested; pigment can change them.