PET-CF
8 products from 7 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
8 products
Key
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- from the Bambu Lab Filament Guide
- Izod where no Charpy is published
- hardened nozzle
- not published
How the numbers are worked out
Bambu Lab PET-CFStrength XY, MPa74Strength Z, MPa35Modulus XY, GPa4.73Charpy notched, kJ/m²8.6HDT 0.45, °C205HDT 1.8, °C182Price, CAD/kg116Nozzle, °C260–290Bed, °C80–100Chamber, °C45–60Drying, °C, h808–12 h
Bambu Lab PET-CFBambu Lab
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CF22 valuesUnless a row says otherwise: printed specimendryDried before testing (see preparation)annealed at 80 °C for 12 hAll the specimens were annealed and dried at 80 °C for 12 h before testingprint settingsSpecimen Printing Conditions Subjects Data Nozzle Temperature 270 °C Bed Temperature 80 °C Printing Speed 100 mm/s InfillDensity 100% * Allthe specimens were printed at the following settings: Nozzle Temperature = 270 °C, Printing Speed = 100 mm/s, Bed Temperature = 80 °C, InfillDensity = 100%. Allthe specimens were annealed and dried at 80 °C for 12 h before testing. And the | |||
| Tensile modulus XY | 4730 ± 260 MPap. 2: Young's Modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 2160 ± 170 MPap. 2: Young's Modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 74 ± 6 MPap. 2: Tensile Strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 35 ± 5 MPap. 2: Tensile Strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 4.5 ± 1.2 %p. 2: Breaking Elongation Rate (X-Y) | ISO 527, GB/T 1040 | in the median |
| Elongation at break Z | 2.4 ± 0.8 %p. 2: Breaking Elongation Rate (Z) | ISO 527, GB/T 1040 | in the median |
| Flexural modulus XY | 5320 ± 270 MPap. 2: Bending Modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 2210 ± 180 MPap. 2: Bending Modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 131 ± 6 MPap. 2: Bending Strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 49 ± 5 MPap. 2: Bending Strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 36.0 ± 2.7 kJ/m²;p. 2: Impact Strength (X-Y) — unnotched | ISO 179, GB/T 1043 | not in the median: unnotched |
| Charpy impact strength XY | 8.6 ± 0.5 kJ/m²p. 2: Impact Strength (X-Y) — notched | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength Z | 4.5 ± 0.6 kJ/m²p. 2: Impact Strength (Z) | ISO 179, GB/T 1043 | not in the median: notch not stated |
| HDT at 0.45 MPa | 205 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 0.45 MPa | in the median |
| HDT at 1.8 MPa | 182 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 1.8 MPa | in the median |
| Glass transition temperature | 75 °Cp. 2: Glass Transition Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | in the median |
| Vicat softening temperature | 226 °Cp. 2: Vicat Softening Temperature | ISO 306, GB/T 1633 | |
| Melting temperature | 250 °Cp. 2: Melting Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Crystallization temperature | 130 °Cp. 2: Crystallization Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Density | 1.29 g/cm³p. 2: Density | specimen not stated, ISO 1183 | |
| Water absorption | 0.37 %p. 2: Saturated Water | no standard namedAs the sheet prints it: ter Absorption Rate 25 °C, 55% RH | |
| Melt mass-flow rate | 25.3 ± 2.5 g/10 minp. 2: Melt Index | specimen not stated, no standard namedAs the sheet prints it: 280 °C, 2.16 kg | |
| Bambu Lab, Bambu Lab PET-CF safety data sheet1 value | |||
| Fibre content | 12-20 %p. 4: Carbon Fiber | no standard stated | |
Print settings
- Nozzle
- 260–290 °Cown data sheet
- Bed
- 80–100 °Cown data sheet
- Heated chamber
- 45–60 °Cown data sheet
- Drying
- 80 °C for 8–12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
- Annealing
- 80 °C for 12 hown data sheet
Its print profile, in the documents' words
- Nozzle 260 -290 °C; Bed 80 -100 °C; Chamber 45 -60 °C; Drying Blast Drying Oven: 80 °C, 8 -12 hBambu Lab, Bambu Filament Technical Data Sheet - PET-CFRecommended printing settings
Price
116 CAD/kgits one regular price in the sample
2 listings: 1 in its price, 1 with no regular price per kilogram recorded
- Bambu Lab Canada: 109 per kg, sale pricePET-CF - Black (71100) / Filament with spool / 1 kgnot used: no regular price per kilogram recorded; seen 10 Sep 2026
- Bambu Lab Canada: 116 CAD/kgPET-CF - Black (71100) / Filament with spool / 0.5 kgin its price; seen 10 Sep 2026
Its 4 documents
What the maker says (6)
- Good for
Its excellent strength, heat resistance, dimensional stability and low moisture absorption make Bambu PET-CF an ideal choice for load-bearing structures or prints used in high temperature and humid environments.
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 1 - Warping and shrinkage
Carbon fiber improves hardness and mechanical strength, while still help maintain the low warping and shrinkage of ordinary PET.
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 1 - Surface finish
Bambu PET-CF has excellent high temperature resistance and a soft glow appearance.
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 1 - Supports and removal
Support Material Support for PA/PET
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 2 - Odour and emissions
Odor Odorless
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 3 - Benefits
Due to the creep and warping resistance of PET-CF, prints can achieve excellent matching accuracy. *Specimens size (L*W*H): 240*8*15 mm³, Infill density: 60%
Bambu Lab, PET-CF official maker product pagep. 1: exact product features/description/application tips, source text line 116
Chemicals and environment (7)
- Flammability: flammable
Flammable
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFFlammability - Water solubility: insoluble
Insoluble in water
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFSolubility - Acid resistance: not resistant
Not resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFResistance to Acid - Alkali resistance: not resistant
Not resistant
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFResistance to Alkali - Organic solvent resistance: limited
Not resistant to some organic solvents
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFResistance to Organic Solvent - Oil and grease resistance: limited
Resistant to most kinds of oil and grease
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFResistance to Oil and Grease - Post-processing: described in words
the suggested annealing temperature of models printed with Bambu PET-CF is 80 to 140 °C, and the time is 6 to 12 hours.
Bambu Lab, Bambu Filament Technical Data Sheet - PET-CFp. 3: Annealing note
Polymaker Fiberon PET-CF17Strength XY, MPa65.9Strength Z, MPa27.9Modulus XY, GPa5.48Charpy notched, kJ/m²5.1HDT 0.45, °C148HDT 1.8, °C105Price, CAD/kg70Nozzle, °C270–300Bed, °C70–80Chamber, °CnoneDrying, °C, h10010 h
Polymaker Fiberon PET-CF17Polymaker
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Polymaker, Fiberon PET-CF17 Technical Data Sheet23 valuesUnless a row says otherwise: printed specimenannealed at 120 °C for 10 hAll specimens were annealed at 120 °C for 10 hprint settingsPrinted at 300 °C nozzle, 70 °C bed, 100% infill, 2 shells, 3 top and bottom layers, cooling fan off; tensile, flexural and impact specimens to the drawings on the sheet (ASTM D638 / ISO 527, GB/T 1040 and ISO 179, GB/T 1043) (p. 1: how to make specimens) | |||
| Tensile modulus XY | 5481.0 ± 223.7 MPap. 1: Young's modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 3558.8 ± 260.4 MPap. 1: Young's modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 65.9 ± 1.0 MPap. 1: Tensile strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 27.9 ± 1.3 MPap. 1: Tensile strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 2.4 ± 0.5%p. 1: Elongation at break (X-Y) | ISO 527, GB/T 1040 | in the median |
| Elongation at break Z | 0.8 ± 0.1%p. 1: Elongation at break (Z) | ISO 527, GB/T 1040 | in the median |
| Flexural modulus XY | 4744.4± 136.3 MPap. 1: Bending modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 2768.2 ± 422.6 MPap. 1: Bending modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 109.3 ± 2.0 MPap. 1: Bending strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 43.4 ± 8.8 MPap. 1: Bending strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 5.1 ± 0.2 kJ/m2p. 1: Charpy impact strength (X-Y) notched | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength XY | 25.1 ± 2.8 kJ/m2p. 1: Charpy impact strength (X-Y) un-notched | ISO 179, GB/T 1043unnotched | not in the median: unnotched |
| Charpy impact strength Z | 3.1 ± 0.7 kJ/m2p. 1: Charpy impact strength (Z) un-notched | ISO 179, GB/T 1043unnotched | not in the median: unnotched |
| HDT at 0.45 MPa | 147.5 °Cp. 1: Heat deflection temp. ISO 75 0.45MPa | ISO 75As the sheet prints it: ISO 75 0.45MPa | in the median |
| HDT at 1.8 MPa | 105 °Cp. 1: Heat deflection temp. ISO 75 1.8MPa | ISO 75As the sheet prints it: ISO 75 1.8MPa | in the median |
| Glass transition temperature | 79.3 °Cp. 1: Glass transition temp. | specimen not stated, DSCAs the sheet prints it: DSC, 10°C/min | in the median |
| Vicat softening temperature | 238.4 °Cp. 1: Vicat softening temp. | ISO 306, GB/T 1633 | |
| Melting temperature | 241.3 °Cp. 1: Melting temperature | specimen not stated, DSCAs the sheet prints it: DSC, 10°C/min | |
| Crystallization temperature | 202.9 °Cp. 1: Crystallization temp. | specimen not stated, DSCAs the sheet prints it: DSC, 10°C/min | |
| Density | 1.34 g/cm3p. 1: Density | specimen not stated, ISO 1183, GB/T 1033tested at 23°Ctreatment not statedprint settings not stated | |
| Water absorption | 0.53 %p. 1: Equilibrium water absorption | specimen not stated, no standard statedtreatment not statedprint settings not stated | |
| Melt mass-flow rate | 30.7 g/10minp. 1: Melt index | specimen not stated, no standard namedAs the sheet prints it: 270°C, 2.16 kg | |
| Fibre content | PET-CF17 %p. 1: Fibre content | specimen not stated, no standard statedtreatment not statedprint settings not stated | |
Print settings
- Nozzle
- 270–300 °Cown data sheet
- Bed
- 70–80 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 100 °C for 10 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
- Annealing
- 120 °C for 10 hown data sheet
Its print profile, in the documents' words
- Nozzle 270-300 °C; Bed 70-80 °C; Chamber Room temp.; Drying 100 °C/10HPolymaker, Fiberon PET-CF17 Technical Data Sheetp. 1: Build plate temperature, Chamber temperature, Drying temp. and time, Nozzle temperature
Price
70 CAD/kgits one regular price in the sample
1 listing
- Voxel Factory: 70 CAD/kgPolymaker Fiberon PET-CF17 1.75mm 500g (SKU PMK-FBR-PET-CF17-500)in its price; seen 30 Sep 2026
Its 2 documents
What the maker says (8)
- Benefits
It's the preferred choice for engineering 3D printing composite materials, featuring high modulus, heat resistance, moisture insensitivity, and ease of printing.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Warping and shrinkage
For thin-walled areas with a wall thickness of less than 4mm, you can try to add reinforcing ribs or increase the wall thickness to avoid possible annealing deformation.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Supports and removal
For prints with a bridge length of more than 3cm, or a thick layer on the upper part of the bridge; prints with large overhangs or small overhangs; all need to add supports and anneal in the oven together with the supports.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Printing advice
We strongly recommend 120°C, 10h annealing to achieve the best performance of the material.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Printing advice
Before returning the prints, please confirm that the prints have been printed for more than 24h, or placed in an 80-degree oven for 2h to eliminate the internal stress after printing.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Printing advice
During annealing, do not touch the sample with your hands or apply any additional load to the sample.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Printing advice
During annealing, ensure that the temperature in the oven is uniform and there are no obvious obstructions that cause uneven temperature of the sample.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1 - Printing advice
In principle, the sample placement method needs to be consistent with that during printing, and it is best to enter the oven directly together with the base plate.
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1
Chemicals and environment (1)
- Post-processing: described in words
Annealing temp. and time 120 °C/10H
Polymaker, Fiberon PET-CF17 Technical Data Sheetp. 1: Annealing temp. and time
BASF Forward AM Ultrafuse PET CF15Strength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²5.4HDT 0.45, °C74HDT 1.8, °C72Price, CAD/kg—Nozzle, °C250–270Bed, °C65–85Chamber, °CnoneDrying, °C, h654–16 h
BASF Forward AM Ultrafuse PET CF15BASF Forward AM
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summary37 valuesUnless a row says otherwise: printed specimen | |||
| Tensile modulus XY | 6178 MPap. 4: Young’s Modulus7) ISO 527 | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Tensile modulus Z (ZX) | 2822 MPap. 4: Young’s Modulus, ZX-Direction | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 63.2 MPap. 4: Tensile strength, XY-Direction | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z (ZX) | 12.5 MPap. 4: Tensile strength, ZX-Direction | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Elongation at break XY | 3.7 %p. 4: Elongation at Break6) ISO 527 | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Elongation at break Z (ZX) | 0.5 %p. 4: Elongation at Break, ZX-Direction | ISO 527after moisture conditioningSamples were conditioned in standard climate (23°C, 50% RH 72h) | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 5452 MPap. 4: Flexural Modulus ISO 178 | ISO 178 | in the median |
| Flexural modulus XZ | 6293 MPap. 4: Flexural Modulus, XZ-Direction | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural modulus ZX | 2253 MPap. 4: Flexural Modulus, ZX-Direction | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 108 MPap. 4: Flexural Strength ISO 178 | ISO 178 | in the median |
| Flexural strength XZ | 145 MPap. 4: Flexural Strength, XZ-Direction | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural strength ZX | 19.7 MPap. 4: Flexural Strength, ZX-Direction | ISO 178 | not in the median: measured on a bar in another orientation |
| Flexural elongation at break XY | 3.7 %p. 4: Flexural Elongation at Break ISO 178 | ISO 178 | listed under other properties |
| Flexural elongation at break XZ | 2.8 %p. 4: Flexural Elongation at Break, XZ-Direction | ISO 178 | listed under other properties |
| Flexural elongation at break ZX | 0.9 %p. 4: Flexural Elongation at Break, ZX-Direction | ISO 178 | listed under other properties |
| Charpy impact strength XY | 5.4 kJ/m2p. 5: Impact Strength Charpy ISO 179-2 | ISO 179As the sheet prints it: ISO 179-2 | in the median |
| Charpy impact strength XY | 27.8 kJ/m2p. 5: Impact Strength Charpy (unnotched), XY-Direction | ISO 179As the sheet prints it: ISO 179-2 | not in the median: unnotched |
| Charpy impact strength XZ | 4.8 kJ/m2p. 5: Impact Strength Charpy (notched), XZ-Direction | ISO 179As the sheet prints it: ISO 179-2 | not in the median: measured on a bar in another orientation |
| Charpy impact strength ZX | 0.5 kJ/m2p. 5: Impact Strength Charpy (notched), ZX-Direction | ISO 179As the sheet prints it: ISO 179-2 | not in the median: measured on a bar in another orientation |
| Charpy impact strength XZ | 32.0 kJ/m2p. 5: Impact Strength Charpy (unnotched), XZ-Direction | ISO 179As the sheet prints it: ISO 179-2 | not in the median: unnotched |
| Charpy impact strength ZX | 1.3 kJ/m2p. 5: Impact Strength Charpy (unnotched), ZX-Direction | ISO 179As the sheet prints it: ISO 179-2 | not in the median: unnotched |
| Izod impact strength XY | 5.7 J/mphysically implausiblep. 5: Impact Strength Izod (notched), XY-Direction | ISO 180 | not in the median: in J/m |
| Izod impact strength XY | 25.1 J/mphysically implausiblep. 5: Impact Strength Izod (unnotched), XY-Direction | ISO 180 | not in the median: in J/m |
| Izod impact strength XZ | 5.0 J/mphysically implausiblep. 5: Impact Strength Izod (notched), XZ-Direction | ISO 180 | not in the median: in J/m |
| Izod impact strength ZX | 2.0 J/mphysically implausiblep. 5: Impact Strength Izod (notched), ZX-Direction | ISO 180 | not in the median: in J/m |
| Izod impact strength XZ | 22.6 J/mphysically implausiblep. 5: Impact Strength Izod (unnotched), XZ-Direction | ISO 180 | not in the median: in J/m |
| Izod impact strength ZX | 2.4 J/mphysically implausiblep. 5: Impact Strength Izod (unnotched), ZX-Direction | ISO 180 | not in the median: in J/m |
| Hardness | 67 Shore Dp. 5: Shore Hardness D (15s) DIN ISO 7619-1 | ISO 7619As the sheet prints it: 15s DIN ISO 7619-1 | in the median |
| HDT at 0.45 MPa | 74 °Cp. 5: HDT B at 0.45 MPa ISO 75-2 | ISO 75As the sheet prints it: 0.45 MPa ISO 75-2 | in the median |
| HDT at 1.8 MPa | 72 °Cp. 5: HDT A at 1.8 MPa ISO 75-2 | ISO 75As the sheet prints it: 1.8 MPa ISO 75-2 | in the median |
| Glass transition temperature | 79 °Cp. 5: Glass Transition ISO 11357-2 | ISO 11357As the sheet prints it: ISO 11357-2 | in the median |
| Vicat softening temperature | 203 °Cp. 5: Vicat softening point at 50 N ISO 306 | ISO 306As the sheet prints it: 50 N ISO 306 | |
| Vicat softening temperature | 243 °Cp. 5: Vicat softening point at 10 N ISO 306 | ISO 306As the sheet prints it: 10 N ISO 306 | |
| Melting temperature | 245 °Cp. 5: Melting Temperature ISO 11357-3 | ISO 11357As the sheet prints it: ISO 11357-3 | |
| Crystallization temperature | 204 °Cp. 5: Crystallization Temperature ISO 11357-3 | ISO 11357As the sheet prints it: ISO 11357-3 | |
| Melt volume-flow rate | 25 cm3/10 minp. 5: Melt Volume-Flow Rate ISO 1133 | specimen not stated, ISO 1133 | |
| Fibre content | PET CF15 %p. 1: Fibre content | specimen not stated, no standard stated | |
Print settings
- Nozzle
- 250–270 °Cown data sheet
- Bed
- 65–85 °Cown data sheet
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 65 °C for 4–16 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle ) 250 – 270 °C; Bed 65 – 85 °C; Drying to 65 °C in a hot air dryer or vacuum oven 4 to 16 hours.BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summaryp. 3: Recommended printing settings; p. 3: Bed Material
Price
Not in the price sample.
Its 2 documents
What the maker says (4)
- Benefits
strong | stiff
BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summaryp. 1 - Nozzle wear
low abrasiveness
BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summaryp. 1 - Benefits
Easy to print strong and stiff filament with high dimensional stability.
BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summaryp. 3 - Supports and removal
Support material Single material breakaway, Ultrafuse BVOH
BASF Forward AM, Ultrafuse PET CF15 Extended TDS: Complete Technical Documentation and Testing Summaryp. 4
Flashforge PET-CFStrength XY, MPa45Strength Z, MPa—Modulus XY, GPa3.6Charpy notched, kJ/m²5IzodHDT 0.45, °C100HDT 1.8, °C—Price, CAD/kg—Nozzle, °C280–300Bed, °C70–100Chamber, °C25–50Drying, °C, h80≥ 12 h
Flashforge PET-CFFlashforge
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Flashforge, Technical Data Sheet PET-CF Filament9 values | |||
| Tensile modulus XY | 3600-4000 Mpap. 1: Modulus of Elasticity ISO 527 Mpa | ISO 527print settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.6mm; Nozzle Temperature 290 °C; Printing Speed 50mm/s; Wall Thickness 1.8mm; Infill 100% | in the median |
| Tensile strength (yield or break not stated) XY | 45-50 Mpap. 1: Tensile Strength ISO 527 Mpa | ISO 527print settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.6mm; Nozzle Temperature 290 °C; Printing Speed 50mm/s; Wall Thickness 1.8mm; Infill 100% | in the median |
| Elongation at break XY | 6-7 %p. 1: Elongation at Break ISO 527 % | ISO 527print settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.6mm; Nozzle Temperature 290 °C; Printing Speed 50mm/s; Wall Thickness 1.8mm; Infill 100% | in the median |
| Izod impact strength | 5-6 KJ/m2p. 1: Izod Impact Strength ISO 180 KJ/m2 | ISO 180notchedprint settingsTest Equipment Guider IIs (Flashforge); Nozzle Diameter 0.6mm; Nozzle Temperature 290 °C; Printing Speed 50mm/s; Wall Thickness 1.8mm; Infill 100% | in the median |
| HDT at 0.45 MPa | 100 ℃p. 1: HDT@ 0.455 MPa (66 psi) ISO 75 ℃ | ISO 75As the sheet prints it: 0.455 MPa 66 psi ISO 75as printedthe printed model has not been annealed | in the median |
| Density | 1.4 g/cm3p. 1: Density ISO 1183 g/cm3 | ISO 1183 | |
| Water absorption | 0.3 %p. 1: Water Absorption (23℃/24h) ISO 62 % | ISO 62As the sheet prints it: 23℃/24h ISO 62 | |
| Melt mass-flow rate | 3-6 g/10minp. 1: Melt Index MFR (250℃/2.16Kg) ISO 1133 g/10min | ISO 1133As the sheet prints it: 250℃/2.16Kg ISO 1133 | |
| Fibre content | 15% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 280–300 °Cown data sheet
- Bed
- 70–100 °Cown data sheet
- Heated chamber
- 25–50 °Cown data sheet
- Drying
- optional: 80 °C for ≥ 12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 280~300℃ (290℃ recommended); Bed 70~100℃ (90℃ recommended); Chamber Room temperature~50℃; Drying In case the filament has become wet, it should be dried before being used; Using a hot dry air oven at 80℃ for at least 12 hours is recommendedFlashforge, Technical Data Sheet PET-CF Filamentp. 2: Recommended printing settings: Nozzle Temperature; p. 2: Ambient Temperature for Printing; p. 3: Drying note; p. 2: Nozzle Diameter (recommended printing settings)
Price
Not in the price sample.
Its 2 documents
What the maker says (6)
- Benefits
High rigidity/Low warpage/Temperature resistance
Flashforge, Technical Data Sheet PET-CF Filamentp. 1 - Benefits
PET-CF is a polyester modified material containing 15% carbon fiber, characterized by high temperature resistance, low shrinkage and easy-to-print property, with the ability to be printable on non-heated chamber FFF 3D printers.
Flashforge, Technical Data Sheet PET-CF Filamentp. 1 - Supports and removal
Recommended Support Material PVA,PVOH,BVOH
Flashforge, Technical Data Sheet PET-CF Filamentp. 2 - Supports and removal
Otherwise the support structure can be permanently bonded to the model, which makes the support hard to remove.
Flashforge, Technical Data Sheet PET-CF Filamentp. 3 - Supports and removal
If PET-CF is used as the support material for itself, please remove the support structure after the model cools down.
Flashforge, Technical Data Sheet PET-CF Filamentp. 3 - Printing advice
After the printing process, it is recommended to dry the model in an oven at 80-100°C for 1-3 hours in order to increase the strength of the model.
Flashforge, Technical Data Sheet PET-CF Filamentp. 3
Chemicals and environment (1)
- Post-processing: described in words
After the printing process, it is recommended to dry the model in an oven at 80-100°C for 1-3 hours in order to increase the strength of the model.
Flashforge, Technical Data Sheet PET-CF Filamentp. 3: Post-processing note
SIDDAMENT PET CFStrength XY, MPa75Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C260–300Bed, °C60–100Chamber, °CnoneDrying, °C, h90–100≥ 12 h
SIDDAMENT PET CFSIDDAMENT
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SIDDAMENT, PET CF Technical Data Sheet12 values | |||
| Tensile strength (yield or break not stated) XY | 75-85 Mpap. 1: Tensile strength (X-Y) ISO 527 Mpa | ISO 527 | in the median |
| Elongation at break XY | 4~5 %p. 1: Elongation at break (X-Y) | ISO 527 | in the median |
| Elongation at break XZ | 1.5~2.5 %p. 1: Elongation at break (X-Z) | ISO 527 | not in the median: measured on a bar in another orientation |
| Flexural modulus XY | 4500-5000 Mpap. 1: Flexural Modulus (X-Y) ISO 527 Mpa | ISO 527 | in the median |
| Flexural modulus XZ | 2000~2500 Mpap. 1: Flexural Modulus (X-Z) | ISO 527 | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 140-150 Mpap. 1: Flexural Strength (X-Y) ISO178 Mpa | ISO 178 | in the median |
| Izod impact strength XY | 25~30 KJ/m2p. 1: Impact Strength (X-Y) | ISO 180 | not in the median: notch not stated |
| HDT at 0.45 MPa | 190 °Cphysically implausiblep. 1: HDT@ 0.455 MPa(66 psi) ISO75 | ISO 75As the sheet prints it: ISO75; 0.455 MPa (66 psi)print settingsTest Sample Printing Conditions: (p. 2; the conditions are drawn on the page image) | not in the median: physically implausible as published |
| Continuous service temperature | 150 °Cp. 1: Continuous Use Temperature | IEC 60216 | |
| Density | 1.3~1.31 g/cm3p. 1: Density | ISO 1183 | |
| Melt mass-flow rate | 3-6 g/10minp. 1: MFR(190°C/2.16Kg) ISO 1133 g/10min | ISO 1133As the sheet prints it: 190°C/2.16Kg ISO 1133 | |
| Fibre content | 10% carbon fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 260–300 °CBambu Lab Filament Guide
- Bed
- 60–100 °CBambu Lab Filament Guide
- Heated chamber
- not requiredown data sheet
- Drying
- 90–100 °C for ≥ 12 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Chamber used on non-heated chamber FDM 3D printers; Drying It is recommended to dry the consumables in a hot air oven at 90°C~100°C for at least 12 hoursSIDDAMENT, PET CF Technical Data Sheetp. 1: Drying note; p. 1: Description
Price
Not in the price sample.
Its 2 documents
What the maker says (6)
- Benefits
High stiffness
SIDDAMENT, PET CF Technical Data Sheetp. 1 - Benefits
High temperature resistance
SIDDAMENT, PET CF Technical Data Sheetp. 1 - Benefits
It has the characteristics of temperature resistance, low shrinkage and easy printing.
SIDDAMENT, PET CF Technical Data Sheetp. 1 - Benefits
It can be used on non-heated chamber FDM 3D printers.
SIDDAMENT, PET CF Technical Data Sheetp. 1 - Benefits
It has excellent rigidity and tensile strength and can be used for a long time at temperatures of 150°C
SIDDAMENT, PET CF Technical Data Sheetp. 1 - Warping and shrinkage
Low warping
SIDDAMENT, PET CF Technical Data Sheetp. 1
Chemicals and environment (1)
- Post-processing: described in words
After the model is printed, it is recommended to dry it in an oven at a temperature of 120~130°C for 6~8 hours to improve the strength of the model.
SIDDAMENT, PET CF Technical Data Sheetp. 1: Post-processing note
Spectrum PET CF15Strength XY, MPa80Strength Z, MPa—Modulus XY, GPa9Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C245–270Bed, °C50–70Chamber, °CnoneDrying, °C, h808–12 h
Spectrum PET CF15Spectrum
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Spectrum, TECHNICAL DATA SHEET PET CF158 valuesUnless a row says otherwise: specimen not stateddryDry | |||
| Tensile modulus orientation not stated | 9 GPap. 1: Modulus of elasticity (dry, at 1 mm/min) | printed specimen (implied by the document), ISO 527As the sheet prints it: dry at 1 mm/min ISO 527 | in the median |
| Tensile strength (yield or break not stated) orientation not stated | 80 MPap. 1: Tensile strength (dry, at 50 mm/min) | ISO 527As the sheet prints it: dry at 50 mm/min ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile strain at strength orientation not stated | 2,50 %p. 1: Elongation at max. force (dry, at 50 mm/min) | ISO 527As the sheet prints it: dry at 50 mm/min ISO 527 | listed under other properties |
| Flexural modulus orientation not stated | 8 GPap. 1: Flexural modulus (dry, at 2 mm/min) | printed specimen (implied by the document), ISO 178As the sheet prints it: dry at 2 mm/min ISO 178 | in the median |
| Flexural strength orientation not stated | 130 MPap. 1: Flexural strength (dry, at 10 mm/min) | ISO 178As the sheet prints it: dry at 10 mm/min ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength | 40 kJ/m2p. 1: Charpy impact strength, dry | ISO 179As the sheet prints it: dry ISO 179 | not in the median: unnotched |
| Density | 1.40 g/cm3p. 1: Specific gravity | ISO 1183moisture state not stated | |
| Water absorption | 0.3 %p. 1: Water absorption, 23°C/24h | ISO 62As the sheet prints it: 23°C/24h ISO 62 | |
| Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–291 value | |||
| Fibre content | 15% Carbon fiber reinforcedp. 21: Fibre content | no standard stated | |
Print settings
- Nozzle
- 245–270 °Cown data sheet
- Bed
- 50–70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 80 °C for 8–12 hBambu Lab Filament Guide
- Hardened nozzle
- neededown data sheet
Its 3 print profiles, in the documents' words
- Nozzle 245-270°C; Bed 50-70°CSpectrum, TECHNICAL DATA SHEET PET CF15p. 1: Recommended printing settings; p. 1: Recommended nozzle
- Bed 50-70 °C; Chamber not necessarySpectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIOp. 5: Bed temp. [°C]; p. 5: Closed chamber for printing; p. 5: Dry box recommended; p. 5: Ruby or hardened nozzle recommended; p. 5: Adhesive
- No temperature statedSpectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29p. 24: Dry box recommended; p. 24: Ruby or hardened nozzle recommended
Price
Not in the price sample.
Its 4 documents
What the maker says (12)
- Benefits
chemical resistance to lubricants and oils
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Benefits
a relatively high resistance to thermal ageing
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Benefits
It is the easiest-to-print material filled with carbon fiber on the market and shows much better temperature and mechanical properties than PET-G based materials.
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Benefits
It presents no retraction issues and does not require a heating chamber.
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Surface finish
It demonstrates a perfect surface finish directly from the printer, thus reducing the need for further treatments.
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Adhesion between layers
very robust interlayer lamination
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Moisture sensitivity
Dry box recommended
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Nozzle wear
Ruby or hardened nozzle recommended
Spectrum, TECHNICAL DATA SHEET PET CF15p. 1 - Benefits
15% Carbon fiber reinforced, high Z-strength; high hardness, stiffness & creep resistance
Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29p. 21 - Adhesion between layers
interlayer adhesion, chemical resistance to lubricants & oils
Spectrum, Spectrum Filaments Product Portfolio 2025 — Prografen pp28–29p. 21 - Benefits
15% Carbon fiber reinforced, high Z-strength; high hardness, stiffness & creep resistance,
Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIOp. 3 - Adhesion between layers
excellent interlayer adhesion, chemical resistance to lubricants & oils
Spectrum, 3D Printing Filament Manufacturer PRODUCT PORTFOLIOp. 3
Raise3D Hyper Speed PET CFStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C150HDT 1.8, °C110Price, CAD/kg—Nozzle, °C260–300Bed, °C60–100Chamber, °CnoneDrying, °C, h808–12 h
Raise3D Hyper Speed PET CFRaise3D
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheet30 valuesUnless a row says otherwise: printed specimenafter moisture conditioningConditionedprint settingsNozzle temp. = 300 ºC; Bed temp.= 70 ºC; Infill= 100% | |||
| Tensile modulus XY | 5400 ± 200 MPap. 1: Young’s modulus (MPa) (5400 ± 200) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Tensile modulus XY | 5000± 170 MPap. 2: Young’s modulus (MPa) (XY) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile modulus Z (ZX) | 2600 ± 150 MPap. 2: Young’s modulus (MPa) (ZX) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile modulus ZX | 3500 ± 300 MPap. 1: Young’s modulus (MPa) (3500 ± 300) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 70 ± 1.0 MPap. 1: Tensile strength (MPa) (70 ± 1.0) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 55± 0.3 MPap. 2: Tensile strength (MPa) (XY) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z (ZX) | 25± 2.0 MPap. 2: Tensile strength (MPa) (ZX) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) ZX | 28 ± 1.1 MPap. 1: Tensile strength (MPa) (28 ± 1.1) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Elongation at break XY | 2.8 ± 0.5 %p. 1: Elongation at break (%) (2.8 ± 0.5) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Elongation at break XY | 4 ± 0.5 %p. 2: Elongation at break (%) (XY) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Elongation at break Z (ZX) | 1.5 ± 0.6 %p. 2: Elongation at break (%) (ZX) | ISO 527as printedbefore annealed | not in the median: measured after moisture conditioning |
| Elongation at break ZX | 0.9 ± 0.1 %p. 1: Elongation at break (%) (0.9 ± 0.1) | ISO 527annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 4700 ± 150 MPap. 1: Bending modulus (MPa) (4700 ± 150) | ISO 178annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 4500 ± 35.0 MPap. 2: Bending modulus (MPa) (XY) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural modulus ZX | 2700 ± 450 MPap. 1: Bending modulus (MPa) (2700 ± 450) | ISO 178annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Flexural modulus ZX | 3300± 100.0 MPap. 2: Bending modulus (MPa) (ZX) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural strength XY | 110 ± 2.0 MPap. 1: Bending strength (MPa) (110 ± 2.0) | ISO 178annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Flexural strength XY | 95 ± 1.0 MPap. 2: Bending strength (MPa) (XY) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Flexural strength ZX | 45 ± 8.8 MPap. 1: Bending strength (MPa) (45 ± 8.8) | ISO 178annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Flexural strength ZX | 45 ± 2 MPap. 2: Bending strength (MPa) (ZX) | ISO 178as printedbefore annealed | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 27 ± 2.8 (Un-notched) kJ/m²p. 1: Charpy impact strength (kJ/m²) (27 ± 2.8 (Un-notched)) | ISO 179annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 5.0 ± 0.3 kJ/m²p. 2: Charpy impact strength (kJ/m²) (XY) | ISO 179as printedbefore annealed | not in the median: measured after moisture conditioning |
| Charpy impact strength ZX | 3.3± 0.7 (Un-notched) kJ/m²p. 1: Charpy impact strength (kJ/m²) (3.3± 0.7 (Un-notched)) | ISO 179annealed at 120 °C for 10 hafter annealed; annealed at 120 ºC for 10h | not in the median: measured after moisture conditioning |
| Charpy impact strength ZX | 3.0 ± 0.1 kJ/m²p. 2: Charpy impact strength (kJ/m²) (ZX) | ISO 179as printedbefore annealed | not in the median: measured after moisture conditioning |
| HDT at 0.45 MPa | 150 °Cp. 2: Heat distortion temperature (°C) (150) | ISO 75As the sheet prints it: ISO 75; 0.45 MPaannealed at 120 °C for 10 hannealed at 120 ºC for 10h | in the median |
| HDT at 1.8 MPa | 110 °Cp. 2: Heat distortion temperature (°C) (110) | ISO 75As the sheet prints it: ISO 75; 1.8 MPaannealed at 120 °C for 10 hannealed at 120 ºC for 10h | in the median |
| Density | 1.34 g/cm³p. 1: Density | specimen not stated, ISO 1183, GB/T 1033moisture state not statedprint settings not stated | |
| Water absorption | 0.53 %p. 1: Water absorption | specimen not stated, no standard statedmoisture state not statedprint settings not stated | |
| Melt mass-flow rate | 31 g/10 minp. 2: Melt flow index (g/10 min) | specimen not stated, no standard namedAs the sheet prints it: 2.16 kg | |
| Fibre content | 15 wt.%p. 1: Fibre content | specimen not stated, no standard statedmoisture state not statedprint settings not stated | |
Print settings
- Nozzle
- 260–300 °CBambu Lab Filament Guide
- Bed
- 60–100 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 80 °C for 8–12 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
- Annealing
- 120 °C for 10 hown data sheet
Its 2 print profiles, in the documents' words
- No temperature statedRaise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1: the conditions the test specimens were printed under, which are not printing guidance
- No temperature statedRaise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 2: the conditions the test specimens were printed under, which are not printing guidance
Price
Not in the price sample.
Its 2 documents
What the maker says (5)
- Good for
an ideal choice for engineering-grade composite parts used in many heavy-duty, humidity and high-temp applications.
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1 - Benefits
Raise3D Hyper Speed PET CF is a carbon fiber-reinforced (15 wt.%) polyethylene terephthalate (PET) filament engineered for Hyper FFF® (L2, 300 mm/s) and high-performance applications.
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1 - Benefits
Hyper speed PET CF exhibits superior mechanical properties high (E >4.5 GPa) and enhanced thermal resistance(HDT > 110 °C), while maintaining low moisture absorption and excellent printability thanks to the optimized carbon fiber length distribution and crystallinity of PET.
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1 - Precision and tolerance
Printed part from Hyper Speed PET CF is long-term dimensional accurate and stable with smooth matt surface finishing
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1 - Odour and emissions
Odor / Almost odorless
Raise3D, Raise3D Hyper Speed PET CF Technical Data Sheetp. 1
Raise3D Industrial PET CFStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C87HDT 1.8, °C77Price, CAD/kg113Nozzle, °C260–300Bed, °C60–100Chamber, °CnoneDrying, °C, h70–808–12 h
Raise3D Industrial PET CFRaise3D
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Raise3D, Raise3D Industrial PET CF Technical Data Sheet23 valuesThe same values also in Raise3D, Raise3D Industrial PET CF Technical Data Sheet.Unless a row says otherwise: printed specimen | |||
| Tensile modulus XY | 5731 ± 261 MPap. 1: Young’s modulus (MPa), XY, Flat | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Tensile modulus XY | 6228 ± 544 MPap. 2: Young’s modulus (MPa), XY Flat, after annealing | ISO 527after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Tensile modulus Z (ZX) | 3270 ± 63 MPap. 1: Young’s modulus (MPa), ZX, Upright | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Tensile modulus orientation not stated | 6 GPap. 1: tensile modulus and strength of over | specimen not stated, no standard statedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8h | not in the median: annealed; the as-printed value is in it |
| Tensile strength (yield or break not stated) XY | 73 ± 2 MPap. 1: Tensile strength (MPa), XY, Flat | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 68 ± 3 MPap. 2: Tensile strength (MPa), XY Flat, after annealing | ISO 527after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z (ZX) | 34 ± 2 MPap. 1: Tensile strength (MPa), ZX, Uprightalso in Raise3D, Raise3D Industrial PET CF Technical Data Sheet | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Elongation at break XY | 2.49 ± 0.22 %p. 1: Elongation at break (%), XY, Flat | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Elongation at break XY | 1.47 ± 0.10 %p. 2: Elongation at break (%), XY Flat, after annealing | ISO 527after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Elongation at break Z (ZX) | 1.20 ± 0.08 %p. 1: Elongation at break (%), ZX, Upright | ISO 527after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 5346 ± 232 MPap. 1: Bending modulus (MPa), XY, Flat | ISO 178after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 5670 ± 334 MPap. 2: Bending modulus (MPa), XY Flat, after annealing | ISO 178after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Flexural strength XY | 115 ± 2 MPap. 1: Bending strength (MPa), XY, Flat | ISO 178after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Flexural strength XY | 109 ± 4 MPap. 2: Bending strength (MPa), XY Flat, after annealing | ISO 178after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 7.75 ± 1.08 kJ/m²p. 1: Charpy impact strength (kJ/m²), XY, Flat | ISO 179after moisture conditioningAll specimens were immerged in ambient temperature for 3 days prior to testingas printedConditioned, before annealedprint settingsNozzle temp.= 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100 %; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 4.30 ± 0.28 kJ/m²p. 2: Charpy impact strength (kJ/m²), XY Flat, after annealing | ISO 179after moisture conditioningConditionedannealed at 100 °C for 8 hAll specimens were annealed at 100 ºC for 8hprint settingsNozzle temp. = 320 ºC; Bed temp.= 80 ºC; Print speed= 45 mm/s; Infill= 100%; Infill angle= ±45 °. | not in the median: measured after moisture conditioning |
| HDT at 0.45 MPa | 175 °Cp. 2: Heat distortion temperature, ISO 75 @0.45 MPa, annealed | ISO 75As the sheet prints it: ISO 75 @0.45 MPaannealed at 100 °C for 8 hannealed at 100 ºC for 8h | not in the median: annealed; the as-printed value is in it |
| HDT at 0.45 MPa | 87 °Cp. 2: Heat distortion temperature, ISO 75 @0.45 MPa, before annealing | ISO 75As the sheet prints it: ISO 75 @0.45 MPaas printedas printed without annealing | in the median |
| HDT at 1.8 MPa | 105 °Cp. 2: Heat distortion temperature, ISO 75 @1.8 MPa, annealed | ISO 75As the sheet prints it: ISO 75 @1.8 MPaannealed at 100 °C for 8 hannealed at 100 ºC for 8h | not in the median: annealed; the as-printed value is in it |
| HDT at 1.8 MPa | 77 °Cp. 2: Heat distortion temperature, ISO 75 @1.8 MPa, before annealing | ISO 75As the sheet prints it: ISO 75 @1.8 MPaas printedas printed without annealing | in the median |
| Density | 1.30 g/cm3p. 1: Density (g/cm³)also in Raise3D, Raise3D Industrial PET CF Technical Data Sheet | specimen not stated, ISO 1183, GB/T 1033 | |
| Water absorption | 0.5 %p. 1: Water absorption (%)also in Raise3D, Raise3D Industrial PET CF Technical Data Sheet | specimen not stated, ISO 62As the sheet prints it: ISO 62: Method 1 | |
| Melt mass-flow rate | 6.8 g/10 minp. 2: Melt flow index (g/10 min) | specimen not stated, no standard namedAs the sheet prints it: 270 °C, 2.16 kg | |
Raise3D, Raise3D Industrial PET CF Technical Data Sheet12 valuesUnless a row says otherwise: printed specimenannealed at 80 °C for 8 hAll specimens were annealed at 80˚C for 8hprint settingsAll testing specimens were printed under the following conditions: Nozzle temp. 300ºC; Bed temp. 80ºC; Print speed 45mm/s; Infill 100%; Infill angle ±45° | |||
| Tensile modulus XY | 6030 ± 350 MPap. 1: Young’s modulus (X-Y) ISO 527, GB/T 1040 | ISO 527, GB/T 1040 | not in the median: annealed; the as-printed value is in it |
| Tensile modulus Z | 3200 ± 75 MPap. 1: Young’s modulus (Z) ISO 527, GB/T 1040 | ISO 527, GB/T 1040 | not in the median: annealed; the as-printed value is in it |
| Tensile strength (yield or break not stated) XY | 87 ± 4 MPap. 1: Tensile strength (X-Y) ISO 52 7, GB/T 1040 | ISO 527, GB/T 1040 | not in the median: annealed; the as-printed value is in it |
| Elongation at break XY | 2.01 ± 0.17 %p. 1: Elongation at break (X-Y) ISO 527, GB/T 1040 | ISO 527, GB/T 1040 | not in the median: annealed; the as-printed value is in it |
| Elongation at break Z | 1.25 ± 0.09 %p. 1: Elongation at break (Z) ISO 527, GB/T 1040 | ISO 527, GB/T 1040 | not in the median: annealed; the as-printed value is in it |
| Flexural modulus XY | 5300 ± 200 MPap. 2: Bending modulus (X-Y) ISO 178, GB/T 9341 | ISO 178, GB/T 9341 | not in the median: annealed; the as-printed value is in it |
| Flexural strength XY | 123 ± 5 MPap. 2: Bending strength (X-Y) ISO 178, GB/T 9341 | ISO 178, GB/T 9341 | not in the median: annealed; the as-printed value is in it |
| Charpy impact strength XY | 5.60 ± 0.58 KJ/m2p. 2: Charpy impact strength (X-Y) ISO 179, GB/T 1043 | ISO 179, GB/T 1043 | not in the median: annealed; the as-printed value is in it |
| HDT at 0.45 MPa | 149 °Cp. 1: Heat Deflection Temperature (°C), ISO75 0.45 MPa | printed specimen (implied by the document), ISO 75As the sheet prints it: ISO75 0.45 MPa | not in the median: annealed; the as-printed value is in it |
| HDT at 1.8 MPa | 112 °Cp. 1: Heat Deflection Temperature (°C), ISO75 1.8MPa | printed specimen (implied by the document), ISO 75As the sheet prints it: ISO75 1.8MPa | not in the median: annealed; the as-printed value is in it |
| Melt mass-flow rate | 4.7 g/10 minp. 1: Melt index (g/10 min) | specimen not stated, no standard namedAs the sheet prints it: 270 °C, 2.16 kg | |
| Fibre content | 15wt% carbon fibersp. 1: Fibre content | specimen not stated, no standard statedtreatment not statedprint settings not stated | |
Print settings
- Nozzle
- 260–300 °CBambu Lab Filament Guide
- Bed
- 60–100 °CBambu Lab Filament Guide
- Heated chamber
- not requiredBambu Lab Filament Guide
- Drying
- 70–80 °C for 8–12 hown data sheet
- Hardened nozzle
- neededown data sheet
- Annealing
- 80 °C for 8 h; 100 °C for 8 hown data sheet
Its 2 print profiles, in the documents' words
- Drying Dry PET CF at 70-80°C for 8-12 hours before printingRaise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2: the notes under the test specimens' conditions, the sheet's only printing guidance; p. 2: Notes. Its nozzle and bed temperatures are the specimens' print conditions, which are not printing guidance.
- Drying Dry PET CF at 70-80°C for 8-12 hours before printingRaise3D, Raise3D Industrial PET CF Technical Data Sheetp. 1: the notes under the test specimens' conditions, the sheet's only printing guidance; p. 2: Notes. Its nozzle and bed temperatures are the specimens' print conditions, which are not printing guidance.
Price
113 CAD/kgthe median of its 2 regular prices in the sample
2 listings
- Shop3D.ca: 115 CAD/kgRaise3D Industrial PET CF Filament - 1.75mm (1kg) - Black (SKU [S]5.11.19025A01)in its price; seen 30 Sep 2026
- DigitMakers: 110 CAD/kgRaise3D Industrial PET CF Filament 1.75mm 1kg Black (SKU R3D-FL-PET-CF-1.75-1KG-BLK)in its price; seen 30 Sep 2026
Its 3 documents
What the maker says (15)
- Benefits
Well-dispersed 15wt% carbon fibers enhance the rigidity, strength, heat and chemical resistance of PET matrix.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 1 - Odour and emissions
Odor / Almost odorless
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 1 - Warping and shrinkage
After annealing, a maximum of 0.1 % dimensional shrinkage could be observed along the Z-axis, depending on infill and layer height, and no significant dimensional shrinkage along the XY-axes
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Moisture sensitivity
Dry PET CF at 70-80°C for 8-12 hours before printing, as low moisture content is crucial for final printed part quality.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Moisture sensitivity
After drying, we recommend storing PET CF filaments inside Raise3D Filament Dry Box during the printing process.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Nozzle wear
Using an abrasion-resistant nozzle, such as hardened steel or a ruby nozzle, is highly recommended.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Supports and removal
If PET CF is also used as the support material, please remove the support structure after annealing.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Printing advice
For a small size model (side length <50 mm), annealing at 80°C for 8 hours is recommended; For a medium-size model (50mm<side length <150 mm), annealing at 80°C for 12 hours is recommended; For a large size model, 100°C for at least 12 hours is recommended.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Good for
strong and cost-effective end-use applications, such as jigs & fixtures and functional parts.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 1 - Benefits
Well-dispersed 15 wt% carbon fibers enhance the rigidity, strength, heat and chemical resistance of PET matrix.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 1 - Warping and shrinkage
After annealing, max. 0.1 % dimensional shrinkage could be observed in Z-axis depending on infill
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Moisture sensitivity
Dry PET CF at 70-80°C for 8-12 hours before printing, moisture content is crucial for final printed part quality.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Moisture sensitivity
After drying, we recommend to store PET CF filaments into Raise3D Filaments Dry Box during the printing.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Nozzle wear
Using abrasion resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2 - Supports and removal
If PET CF is used as the support material for itself, please remove the support structure after annealing.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 3
Chemicals and environment (1)
- Post-processing: described in words
After printing, it is recommended to anneal the model in an oven at 80-100°C for 8-12 hours.
Raise3D, Raise3D Industrial PET CF Technical Data Sheetp. 2: Annealing note
No product matches "".
Values are for the colour each sheet tested; pigment can change them.