PA6/66
7 products from 6 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
7 products
Key
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- Izod where no Charpy is published
- shared data sheet
- hardened nozzle
- not published
How the numbers are worked out
Polymaker PolyMide CoPAStrength XY, MPa78Strength Z, MPa45.8Modulus XY, GPa2.7Charpy notched, kJ/m²6.9HDT 0.45, °C111HDT 1.8, °C70Price, CAD/kg91Nozzle, °C250–270Bed, °C25–50Chamber, °C40–60Drying, °C, h8012 h
Polymaker PolyMide CoPAPolymaker
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Polymaker, PolyMide CoPA27 valuesThe same values also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA, Polymaker, PolyMide™ CoPA and Polymaker, PolyMide™ CoPA Technical Data Sheet.Unless a row says otherwise: printed specimenannealed at 80 °C for 0.5 hAll specimens were annealed at 80˚C for 30min and dried for 48h prior to testingprint settingsPrinting temperature 265 °C Bed temperature 50 °C Shell 2 Top & bottom layer 4 Infill 100% Environmental temperature 60 ˚C Cooling fan OFF The typical values presented in this data sheet are intended for reference and comparison purposes only. They should not be used for design specifications or quality control purpose | |||
| Tensile modulus XY | 2223 ± 199 MPap. 4: Young’s modulus (X-Y)also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Tensile modulus XY | 1053 ± 235 MPap. 4: Young’s modulus (X-Y) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Tensile modulus Z | 2564 ± 97 MPap. 4: Young’s modulus (Z) | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Tensile modulus Z | 702 ± 16 MPap. 4: Young’s modulus (Z) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 66.2 ± 0.9 MPap. 4: Tensile strength (X-Y)also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Tensile strength (yield or break not stated) XY | 31.4 ± 1.5 MPap. 4: Tensile strength (X-Y) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z | 43.3 ± 9.1 MPap. 4: Tensile strength (Z) | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Tensile strength (yield or break not stated) Z | 31.4 ± 1.5 MPap. 4: Tensile strength (Z) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Elongation at break XY | 9.9 ± 1.5 %p. 4: Elongation at break (X-Y)also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Elongation at break XY | 216.5 ± 12.1 %p. 4: Elongation at break (X-Y) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Elongation at break Z | 1.8 ± 0.4 %p. 4: Elongation at break (Z) | ISO 527, GB/T 1040dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Elongation at break Z | 4.6 ± 0.2 %p. 4: Elongation at break (Z) | ISO 527, GB/T 1040after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 1667 ± 118 MPap. 4: Bending modulus (X-Y)also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA | ISO 178, GB/T 9341dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Flexural modulus XY | 862.8 ± 133.3 MPap. 4: Bending modulus (X-Y) | ISO 178, GB/T 9341after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Flexural strength XY | 97 ± 1.1 MPap. 4: Bending strength (X-Y)also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA | ISO 178, GB/T 9341dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Flexural strength XY | 41.6 ± 11.6 MPap. 4: Bending strength (X-Y) | ISO 178, GB/T 9341after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 9.6 ± 1.4 kJ/m2p. 4: Charpy impact strength (X-Y) | ISO 179, GB/T 1043dryDried before testing (see preparation) | not in the median: another value of this product is in it |
| Charpy impact strength XY | 17.2 ± 1.4 kJ/m2p. 4: Charpy impact strength (X | ISO 179, GB/T 1043after moisture conditioningConditioned: 70% RH | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 4.5 ± 1.5 kJ/m2p. 4: Low temperature impact strength (X-Y), -30°C | ISO 179As the sheet prints it: ISO 179-1/1eA:2010dryDried before testing (see preparation) | not in the median: tested below room temperature |
| HDT at 0.45 MPa | 110.5 °Cp. 3: Heat deflection temperature | ISO 75As the sheet prints it: ISO 75 0.45MPadryDried before testing (see preparation) | in the median |
| HDT at 1.8 MPa | 69.8 °Cp. 3: Heat deflection temperature | ISO 75As the sheet prints it: ISO 75 1.8MPadryDried before testing (see preparation) | in the median |
| Glass transition temperature | 67 °Cp. 3: Glass transition temperaturealso in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA | DSCAs the sheet prints it: DSC, 10°C/min | in the median |
| Vicat softening temperature | 180 °Cp. 3: Vicat softening temperaturealso in Polymaker, PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA Technical Data Sheet | ISO 306, GB/T 1633dryDried before testing (see preparation) | |
| Melting temperature | 190 °Cp. 3: Melting temperaturealso in Polymaker, PolyMide™ CoPA | DSCAs the sheet prints it: DSC, 10°C/min | |
| Crystallization temperature | 128 °Cp. 3: Crystallization temperaturealso in Polymaker, PolyMide™ CoPA | DSCAs the sheet prints it: DSC, 10°C/min | |
| Density | 1.12 g/cm3p. 2: Densityalso in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA Technical Data Sheet | specimen not stated, ISO 1183, GB/T 1033treatment not stated | |
| Water absorption | 2.82 %p. 2: Equilibrium water absorption (%) | specimen not stated, no standard namedAs the sheet prints it: Equilibrium water absorption | |
| Also named without a value: flexural modulus, flexural strength, charpy impact strength, thermal conductivity. | |||
Polymaker, PolyMide™ CoPA Technical Data Sheet20 valuesThe same values also in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA and Polymaker, PolyMide™ CoPA.Unless a row says otherwise: printed specimenprint settingsPrinting temperature 260°C; Infill 100%; Bed temperature 50°C; Shell 2; Top & bottom layer 3; Cooling fan OFF; Environmental Temperature Ambient temp. | |||
| Tensile modulus XY | 2703 ± 259 MPap. 1: Young’s modulus (X-Y) | ISO 527, GB/T 1040dryDry Status | in the median |
| Tensile modulus XY | 724 ± 61 MPap. 1: Young’s modulus (X-Y), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Tensile modulus Z | 2209 ± 59 MPap. 1: Young’s modulus (Z) | ISO 527, GB/T 1040dryDry Status | in the median |
| Tensile modulus Z | 660 ± 29 MPap. 1: Young’s modulus (Z), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) XY | 78.0 ± 0.7 MPap. 1: Tensile strength (X-Y) | ISO 527, GB/T 1040dryDry Status | in the median |
| Tensile strength (yield or break not stated) XY | 34.3 ± 2.5 MPap. 1: Tensile strength (X-Y), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Tensile strength (yield or break not stated) Z | 45.8 ± 1.5 MPap. 1: Tensile strength (Z) | ISO 527, GB/T 1040dryDry Status | in the median |
| Tensile strength (yield or break not stated) Z | 13.7 ± 1.2 MPap. 1: Tensile strength (Z), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Elongation at break XY | 12.7 ± 2.1 %p. 1: Elongation at break (X-Y) | ISO 527, GB/T 1040dryDry Status | in the median |
| Elongation at break XY | 13.2 ± 2.3 %p. 1: Elongation at break (X-Y), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Elongation at break Z | 1.3 ± 0.1 %p. 1: Elongation at break (Z) | ISO 527, GB/T 1040dryDry Status | in the median |
| Elongation at break Z | 1.7 ± 0.2 %p. 1: Elongation at break (Z), Wet Status | ISO 527, GB/T 1040after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Flexural modulus XY | 2510 ± 25 MPap. 1: Bending modulus (X-Y) | ISO 178, GB/T 9341dryDry Status | in the median |
| Flexural modulus XY | 636 ± 11 MPap. 1: Bending modulus (X-Y), Wet Status | ISO 178, GB/T 9341after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Flexural strength XY | 109.8 ± 1.3 MPap. 1: Bending strength (X-Y) | ISO 178, GB/T 9341dryDry Status | in the median |
| Flexural strength XY | 22.6 ± 0.5 MPap. 1: Bending strength (X-Y), Wet Status | ISO 178, GB/T 9341after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Charpy impact strength XY | 6.9 ± 1.4 kJ/m2p. 1: Notched charpy impact strength (X-Y) | ISO 179, GB/T 1043dryDry Status | in the median |
| Charpy impact strength XY | 27.7 ± 1.2 kJ/m2p. 1: Notched charpy impact strength (X-Y), Wet Status | ISO 179, GB/T 1043after moisture conditioningWet Status | not in the median: measured after moisture conditioning |
| Glass transition temperature | 66 °Cp. 1: Glass transition temp. DSC, 10°C/min | specimen not stated, DSCprint settings not stated | not in the median: another value of this product is in it |
| Melt mass-flow rate | 12 g/10minp. 1: Melt index 260°C, 1.2kgalso in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAalso in Polymaker, PolyMide™ CoPA | specimen not stated, no standard namedAs the sheet prints it: 260°C 1.2kg | |
Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA4 valuesUnless a row says otherwise: printed specimenafter moisture conditioningConditioned: 50% RH, ambient temperatureannealed at 80 °C for 0.5 hAll specimens were annealed at 80 °C for 30 min, and conditioned at 50% relative humidity and ambient temperature for 15 days prior to testing www.polymaker.com | |||
| Flexural modulus orientation not stated | 862.8 ± 133.3 MPap. 1: Bending modulus ASTMD790 (ISO 178, GB/T 9341) | ASTM D790, ISO 178, GB/T 9341As the sheet prints it: 790 ASTMD790 ISO 178 GB/T 9341 | not in the median: measured after moisture conditioning |
| Flexural strength orientation not stated | 41.6 ± 11.6 MPap. 1: Bending strength ASTMD790 (ISO 178, GB/T 9341) | ASTM D790, ISO 178, GB/T 9341As the sheet prints it: 790 ASTMD790 ISO 178 GB/T 9341 | not in the median: measured after moisture conditioning |
| Impact strength, test unclear XY | 9.6 ± 1.4 kJ/m2p. 1: Charpy impact strength (X-Y) ASTM D256 (ISO 179, GB/T 1043) | ASTM D256, ISO 179, GB/T 1043dryDried before testing (see preparation) | listed under other properties |
| Impact strength, test unclear | 17.2 ± 1.4 kJ/m2p. 1: Charpy impact strength ASTM D256 (ISO 179, GB/T 1043) | ASTM D256, ISO 179, GB/T 1043As the sheet prints it: 256 ASTM D256 ISO 179 GB/T 1043 | listed under other properties |
| Polymaker, PolyMide™ CoPA3 valuesUnless a row says otherwise: printed specimen (implied by the document) | |||
| Flexural modulus orientation not stated | 1667 ± 118 MPap. 6: Bending modulus ASTM D790 (ISO 178, GB/T 9341) | ASTM D790, ISO 178, GB/T 9341As the sheet prints it: 790 ASTM D790 ISO 178 GB/T 9341 | not in the median: another value of this product is in it |
| Flexural strength orientation not stated | 97.0 ± 1.1 MPap. 6: Bending strength ASTM D790 (ISO 178, GB/T 9341) | ASTM D790, ISO 178, GB/T 9341As the sheet prints it: 790 ASTM D790 ISO 178 GB/T 9341 | not in the median: another value of this product is in it |
| Impact strength, test unclear | 9.6 ± 1.4 kJ/m2p. 6: Charpy impact strength ASTM D256 (ISO 527, GB/T 1040) | specimen not stated, ASTM D256, ISO 527, GB/T 1040As the sheet prints it: 256 ASTM D256 ISO 527 GB/T 1040 | listed under other properties |
Print settings
- Nozzle
- 250–270 °Cown data sheet
- Bed
- 25–50 °Cown data sheet
- Heated chamber
- 40–60 °Cown data sheet
- Drying
- 80 °C for 12 hown data sheet
- Hardened nozzle
- neededown data sheet
- Annealing
- 80 °C for 0.5 hown data sheet
Differs in another document of this product, not used in deciding (a data sheet speaks before a product page, a newer edition before an older one): bed in Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPA.
Its 5 print profiles, in the documents' words
- Nozzle 250 - 270 (℃); Bed 25 - 50 (˚C); Chamber 40 - 60 (˚C)Polymaker, PolyMide CoPARecommended printing settings; p. 5: Nozzle note
- Nozzle 250 - 270 (˚C); Bed 25 - 70 (˚C); Chamber 40 - 60 (˚C)Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAp. 2: Recommended printing settings: Nozzle temperature
- Nozzle 250°C - 270°C; Bed 25°C - 50°C; Drying 80˚C for 12hPolymaker, PolyMide™ CoPAp. 6: Recommended printing settings; p. 6: Drying settings; p. 4: Nozzle note
- Nozzle 250-270°C; Bed 25-50°C; Chamber Needed (ambient temp.); Drying 100°C/8HPolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: Recommended printing settings: Nozzle temperature; p. 1: Closure chamber; p. 1: Drying temp. and time; p. 1: Nozzle note
- Nozzle 250-270 °C; Bed 25-50 °C; Drying 80°C for 8hPolymaker, Polymaker PolyMide CoPA official maker product pagep. 1: Technical Specifications
Price
90.7 CAD/kgits one regular price in the sample
1 listing
- Voxel Factory: 90.7 CAD/kgPolymaker PolyMide Nylon CoPA 1.75mm 0.75kg / Black (SKU PMK-CPA-BLK-175-750)in its price; seen 30 Sep 2026
Its 6 documents
What the maker says (25)
- Nozzle wear
When used extensively, PolyMide™ CoPA can be abrasive to brass nozzles.
Polymaker, PolyMide™ CoPAp. 4 - Nozzle wear
When using PolyMide™ CoPA, we recommend to switch to a wear resistant nozzle such as hardened steel nozzle.
Polymaker, PolyMide™ CoPAp. 4 - Odour and emissions
It is recommended to place the printer in a well ventilated area.
Polymaker, PolyMide™ CoPAp. 4 - Moisture sensitivity
If you hear popping sounds and notice that the surface quality of your print is uneven aor the color is not consistent, the filament has absorbed too much moisture.
Polymaker, PolyMide™ CoPAp. 5 - Moisture sensitivity
PolyMide™ CoPA parts will keep absorbing moisture after the printing process making the parts tougher with more flexibility.
Polymaker, PolyMide™ CoPAp. 5 - Moisture sensitivity
It is highly recommended to store PolyMide™ CoPA in the PolyBox™ to prevent moisture absorption which will lower the quality and the mechanical properties of the print.
Polymaker, PolyMide™ CoPAp. 5 - Printing advice
PolyMide™ CoPA can be annealed right after the printing process at 70˚C for 2 hours to enhance its thermal and mechanical properties.
Polymaker, PolyMide™ CoPAp. 5 - Benefits
The filament combines excellent strength, toughness, and heat resistance of up to 180˚C.
Polymaker, PolyMide™ CoPAp. 6 - Moisture sensitivity
PolyMide™ CoPA is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker, PolyMide CoPAp. 5 - Nozzle wear
Abrasion of the brass nozzle happens quite often when printing PolyMide™ CoPA.
Polymaker, PolyMide CoPAp. 5 - Nozzle wear
A wear-resistant nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with PolyMide™ CoPA.
Polymaker, PolyMide CoPAp. 5 - Supports and removal
Otherwise the support structure can be permanently bonded to the model.
Polymaker, PolyMide CoPAp. 5 - Supports and removal
Recommended support material PolyDissolve™ S1
Polymaker, PolyMide CoPAp. 5 - Supports and removal
If PolyMide™ CoPA is used as the support material for itself, please remove the support structure before excessive moisture absorption.
Polymaker, PolyMide CoPAp. 5 - Moisture sensitivity
It is highly recommended to use the PolyBox™ when printing with PolyMide™ CoPA and to store it in the resealable bag.
Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAp. 2 - Printing advice
To ensure a good heat resistance of your printed part it is recommended to anneal your PolyMide™ CoPA 3d printed model.
Polymaker, Nov. 2018 Technical Data Sheet Version 4.0 PolyMide™ CoPAp. 2 - Benefits
The filament combines excellent strength, toughness, and heat resistance of up to 180˚C.
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Moisture sensitivity
PolyMide™ CoPA is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Nozzle wear
Abrasion of the brass nozzle happens quite often when printing PolyMide™ CoPA.
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Nozzle wear
A wear-resistant nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with PolyMide™ CoPA.
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Supports and removal
Otherwise, the support structure can be permanently bonded to the model.
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Supports and removal
If PolyMide™ CoPA is used as the support material for itself, please remove the support structure before excessive moisture absorption.
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1 - Good for
Ideal for Engineering and Industrial Parts Choose PolyMide™ CoPA when your project demands high strength, toughness, and heat resistance - perfect for automotive, mechanical, and industrial applications.
Polymaker, Polymaker PolyMide CoPA official maker product pagep. 1: exact product Description/Printing Requirements/FAQ; source text line 177 - Pitfalls and limitations
Moisture conditioning refers to allowing the print to absorb moisture. This is inevitble since nylons are hygroscopic, but you can expedite the process by keeping the print in a high humidity climate, or submerging them in water, for 48 hours. All of our test specimens were annealed at 100˚C for 16 hours, and then immerged in water at 60˚C for 48 hours. The average moisture content of specimens is 2.57%.
Polymaker, Polymaker PolyMide CoPA official maker product pagep. 1: exact product Description/Printing Requirements/FAQ; source text line 275 - Printing advice
Drying Settings: 80˚C for 10h (Only if the material has absorbed moisture)
Polymaker, Polymaker PolyMide CoPA official maker product pagep. 1: own product Printing Requirements/Recommendations, source text line 186
Specimen preparation (1)
All specimens were annealed at 80˚C for 30min and dried for 48h prior to testing
Polymaker, PolyMide CoPATest specimen preparation
Chemicals and environment (13)
- Acid resistance: not resistant
Not resistant
Effect of weak acids · weakPolymaker, PolyMide CoPAEffect of weak acids - Acid resistance: not resistant
Not resistant
Effect of strong acids · strongPolymaker, PolyMide CoPAEffect of strong acids - Alkali resistance: limited
Slight resistant
Effect of weak alkalis · weakPolymaker, PolyMide CoPAEffect of weak alkalis - Alkali resistance: not resistant
Not resistant
Effect of strong alkalis · strongPolymaker, PolyMide CoPAEffect of strong alkalis - Organic solvent resistance: not resistant
Not resistant
Effect of organic solventPolymaker, PolyMide CoPAEffect of organic solvent - Oil and grease resistance: resistant
Resistant
Effect of oils and greasePolymaker, PolyMide CoPAEffect of oils and grease - Post-processing: described in words
After the printing process, it is recommended to anneal the model in the oven at 80°C for 6 hours.
Polymaker, PolyMide CoPAp. 5: Annealing note - Post-processing: described in words
Annealing setting 80°C/6H
Polymaker, PolyMide™ CoPA Technical Data Sheetp. 1: Annealing setting - Acid resistance: not resistant
Poor
Effect of weak acids · weakPolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: Effect of weak acids Poor - Acid resistance: not resistant
Poor
Effect of strong acids · strongPolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: Effect of strong acids Poor - Alkali resistance: limited
Fair
Effect of weak alkalis · weakPolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: CHEMICAL RESISTANCE DATA, Effect of weak alkalis and its own generic-rating legend - Alkali resistance: not resistant
Poor
Effect of strong alkalis · strongPolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: CHEMICAL RESISTANCE DATA, Effect of strong alkalis and its own generic-rating legend - Oil and grease resistance: resistant
Good
Effect of oils and greasePolymaker, PolyMide™ CoPA Technical Data Sheetp. 1: CHEMICAL RESISTANCE DATA, Effect of oils and grease and its own generic-rating legend
SUNLU Easy PAStrength XY, MPa61Strength Z, MPa—Modulus XY, GPa1.79Charpy notched, kJ/m²11IzodHDT 0.45, °C119HDT 1.8, °C—Price, CAD/kg—Nozzle, °C255–265Bed, °C30–50Chamber, °CnoneDrying, °C, h80–110
SUNLU Easy PASUNLU
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SUNLU, Product Information Easy PA14 valuesThe same values also in SUNLU, TECHNICAL DATA SHEET ISO Easy PA. | |||
| Tensile modulus orientation not stated | 1790 MPap. 1: Young’s Modulus ASTM D638 1mm/min MPa | ASTM D638As the sheet prints it: 1mm/min ASTM D638 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile strength (yield or break not stated) orientation not stated | 75 MPap. 1: Tensile Strength ASTM D638 50mm/min MPa | ASTM D638As the sheet prints it: 50mm/min ASTM D638 | not in the median: another value of this product is in it |
| Elongation at break orientation not stated | 32 %p. 1: Elongation at break ASTM D638 50mm/min % | ASTM D638As the sheet prints it: 50mm/min ASTM D638 | not in the median: another value of this product is in it |
| Flexural modulus orientation not stated | 2350 MPap. 1: Flexural Modulus ASTM D790 2mm/min MPa | ASTM D790As the sheet prints it: 2mm/min ASTM D790 | not in the median: another value of this product is in it |
| Flexural strength orientation not stated | 98 MPap. 1: Flexural Strength ASTM D790 2mm/min MPa | ASTM D790As the sheet prints it: 2mm/min ASTM D790 | not in the median: another value of this product is in it |
| Izod impact strength | 62 J/mp. 1: IZOD Impact Notched ASTM D256 3.2mm, 23℃ J/m | ASTM D256As the sheet prints it: 3.2mm 23℃ ASTM D256 | not in the median: in J/m |
| HDT at 0.45 MPa | 121 ℃p. 1: Heat Deflection (HDT) ASTM D648 0.45MPa ℃ | ASTM D648As the sheet prints it: 0.45MPa ASTM D648 | not in the median: another value of this product is in it |
| Vicat softening temperature | 135 ℃p. 1: Vicat Softening Temp. ASTM D1525 5kg,50℃/h ℃also in SUNLU, TECHNICAL DATA SHEET ISO Easy PA | ASTM D1525As the sheet prints it: 5kg ASTM D1525 | |
| Melting temperature | 198 ℃p. 1: Melting Point ASTM D7426 10℃/min ℃also in SUNLU, TECHNICAL DATA SHEET ISO Easy PA | ASTM D7426 | |
| Decomposition temperature | 300 ℃p. 1: @5%Decomposition Temp. ASTM E2402 20℃/min ℃also in SUNLU, TECHNICAL DATA SHEET ISO Easy PA | ASTM E2402As the sheet prints it: E2402 | |
| Density | 1.08 g/cm3p. 1: Density ASTM D792 23℃ g/cm3 | ASTM D792As the sheet prints it: 23℃ ASTM D792 | |
| Melt mass-flow rate | 17 g/10minp. 1: Melt Flow Rate ASTM D1238 250℃/2.16kg g/10min | ASTM D1238As the sheet prints it: 250℃/2.16kg ASTM D1238 | |
| Mould shrinkage orientation not stated | 1.3-1.6 %p. 1: Mold Shrinkage ASTM D955 23℃ %also in SUNLU, TECHNICAL DATA SHEET ISO Easy PA | ASTM D955As the sheet prints it: 23℃ ASTM D955 | |
| Relative permittivity | 3.4p. 1: Dielectric Constant | ASTM D150As the sheet prints it: ASTM D150; frequency=1 kHz | |
| SUNLU, TECHNICAL DATA SHEET ISO Easy PA10 valuesThe same values also in SUNLU, Product Information Easy PA.Unless a row says otherwise: printed specimen | |||
| Tensile strength (yield or break not stated) XY | 61 ± 6 MPap. 1: (X-Y) Tensile Strength ISO 527/2 50 mm/min MPa | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | in the median |
| Elongation at break XY | 15 ± 3 %p. 1: (X-Y) Elongation at break ISO 527/2 50 mm/min % | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural modulus XY | 2314 ± 250 MPap. 1: (X-Y) Flexural Modulus ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural strength XY | 91 ± 5 MPap. 1: (X-Y) Flexural Strength ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength XY | 11 ± 3 KJ/m2p. 1: (X-Y) Izod Impact Strength of Notched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength ZX | 5.1 ± 1.5 KJ/m2p. 1: (Z-X) Izod Impact Strength of Unnotched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 70-160 mm/s; Printing temperature 280 °C; Infill: 100%; 90° raster orientation | not in the median: unnotched |
| HDT XY, at 0.45 MPa | 119 ± 3 ℃p. 1: (X-Y) Heat Distortion (HDT) ISO 75 0.45 MPa ℃ | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | in the median |
| Glass transition temperature | 65 ℃p. 1: Glass Transition (Tg) ISO 11357-2 10 ℃/min ℃also in SUNLU, Product Information Easy PA | ISO 11357As the sheet prints it: ISO 11357-2 | in the median |
| Density | 1.10 g/cm3p. 1: Density ISO 1183 23℃ g/cm3 | specimen not stated, ISO 1183As the sheet prints it: 23℃ ISO 1183 | |
| Melt mass-flow rate | 19 ± 2 g/10 minp. 1: Melt Mass-flow Rate ISO 1133 250℃/2.16 kg g/10 min | ISO 1133As the sheet prints it: 250℃/2.16 kg ISO 1133 | |
Print settings
- Nozzle
- 255–265 °Cown data sheet
- Bed
- 30–50 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 80–110 °Cown data sheet
- Hardened nozzle
- not stated
Its 3 print profiles, in the documents' words
- Nozzle 255-265℃; Bed 30-50℃; Chamber Room Temperature; Drying 80- 110℃SUNLU, Product Information Easy PAp. 2: Recommended printing settings; p. 2: Nozzle Print Temp.; p. 2: Room Temp.
- Nozzle 250-270; 270-280; Bed 30-50℃; Chamber Room Temperature; Drying 80-110℃SUNLU, TECHNICAL DATA SHEET ISO Easy PAp. 2: Recommended printing settings; p. 2: Nozzle Temp.
- Nozzle 265-280℃; Bed 30-50℃; Chamber Room Temperature; Drying 80- 110℃SUNLU, Product Information Easy PAp. 2: Recommended Printing Parameters: Zonal Temperature, 100-200mm/s
Price
Not in the price sample.
Its 3 documents
What the maker says (6)
- Benefits
high toughness, strong impact resistance
SUNLU, Product Information Easy PAp. 1 - Warping and shrinkage
No warping, no cracking
SUNLU, Product Information Easy PAp. 1 - Supports and removal
Support Material PVA
SUNLU, Product Information Easy PAp. 2 - Good for
Structural parts, decorative items, toys, accessories, and figurines
SUNLU, TECHNICAL DATA SHEET ISO Easy PAp. 1 - Benefits
high toughness, and excellent impact resistance
SUNLU, TECHNICAL DATA SHEET ISO Easy PAp. 1 - Warping and shrinkage
Low warping and cracking
SUNLU, TECHNICAL DATA SHEET ISO Easy PAp. 1
BigRep PA6/66Strength XY, MPa66Strength Z, MPa—Modulus XY, GPa2.2Charpy notched, kJ/m²31HDT 0.45, °C110HDT 1.8, °C69Price, CAD/kg—Nozzle, °C240–270Bed, °C40–60Chamber, °C—Drying, °C, h806–8 h
BigRep PA6/66BigRep
Only 2.85 mm filament was found; the H2C takes 1.75 mm.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| BigRep, FILAMENT PA6/6610 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile modulus orientation not stated | 2200 MPap. 1: Tensile Modulus (ISO 527) | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile strength (yield or break not stated) orientation not stated | 66 MPap. 1: Tensile Strength (ISO 527) | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural modulus orientation not stated | 1650 MPap. 1: Flexural Modulus (ISO 178) | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 90 MPap. 1: Flexural Strength (ISO 178) | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength | 31 kJ/m²p. 1: Impact Strength, Notched (ISO 179) | ISO 179 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 0.45 MPa | 110 °Cp. 1: HDT B - 0.45 MPa (ISO 75) | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 1.8 MPa | 69 °Cp. 1: HDT A - 1.8 MPa (ISO 75) | ISO 75As the sheet prints it: 1.8 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 66 °Cp. 1: Glass Transition Temperature (Tg) (DSC) | DSCAs the sheet prints it: Tg DSC | in the median |
| Melting temperature | 190 °Cp. 1: Melting Temperature (Tm) (DSC) | DSCAs the sheet prints it: Tm DSC | |
| Density | 1.12 g/cm³p. 1: Density (ISO 1183) | ISO 1183 | |
Print settings
- Nozzle
- 240–270 °Cown data sheet
- Bed
- 40–60 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 80 °C for 6–8 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 240 - 270 °C; Bed 40 - 60 °C; Drying 80 °C for 6 - 8 hoursBigRep, FILAMENT PA6/66p. 1: Recommended printing settings; p. 1: Bed Temperature
Price
Not in the price sample.
Its 2 documents
What the maker says (1)
- Benefits
An excellent choice for industrial applications, BigRep PA6/66 is strong, durable, and lightweight with high resistance to heat and chemicals.
BigRep, FILAMENT PA6/66p. 1
3DXTECH AMIDEX PA6 Copolymer v1 0Strength XY, MPa55Strength Z, MPa—Modulus XY, GPa1.98Charpy notched, kJ/m²—HDT 0.45, °C140HDT 1.8, °C—Price, CAD/kg—Nozzle, °C255–275Bed, °C60–70Chamber, °CnoneDrying, °C, h904 h
3DXTECH AMIDEX PA6 Copolymer v1 03DXTECH
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
3DXTECH, Technical Data Sheet: AmideX™ PA6 Copolymer 3D Printing Filament8 valuesUnless a row says otherwise: printed specimenprint settingsPrinted Specimen Conditions Printer: Gearbox™ HT2 Nozzle: 0.4mm Layer Height: 0.25mm Infill: 100%, +/- 45° Extrusion Temp: 270°C Bed Temp: 80°C Specimen Orientation: XY Flat | |||
| Tensile modulus XY | 1980 MPap. 1: Tensile Modulus | ISO 527 | in the median |
| Tensile break strength XY | 55 MPap. 1: Tensile Strength, Break | ISO 527 | in the median |
| Elongation at break XY | 100 %p. 1: Tensile Elongation, Break | ISO 527 | in the median |
| Flexural modulus XY | 2050 MPap. 1: Flexural Modulus | ISO 178 | in the median |
| Flexural strength XY | 76 MPap. 1: Flexural Strength | ISO 178 | in the median |
| HDT at 0.45 MPa | 140 °Cp. 1: Deflection Temperature at 0.45 | ISO 75As the sheet prints it: ISO 75, 0.45 MPa (66 psi) | in the median |
| Glass transition temperature | 76 °Cp. 1: Glass Transition Temperature | DSC | in the median |
| Density | 1.12 g/ccp. 1: Density | ISO 1183 | |
Print settings
- Nozzle
- 255–275 °Cown data sheet
- Bed
- 60–70 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 90 °C for 4 hown data sheet
- Hardened nozzle
- not neededown data sheet
Its 2 print profiles, in the documents' words
- No temperature stated3DXTECH, Technical Data Sheet: AmideX™ PA6 Copolymer 3D Printing FilamentRecommended printing settings
- Nozzle 255-275C; Bed 60-70C; Chamber Not required; Drying 90C for 4 hours3DXTECH, AmideX Nylon 6-66Print Recommendations
Price
Not in the price sample.
Its 3 documents
MatterHackers PRO Series NylonStrength XY, MPa36.3Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C102HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–260Bed, °C65Chamber, °C—Drying, °C, h758 h
MatterHackers PRO Series NylonMatterHackers
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylon3 valuesUnless a row says otherwise: specimen not stated | |||
| Tensile yield strength orientation not stated | 5260 Yield PSIp. 1: Tensile Strength | ASTM D638As the sheet prints it: ASTM D638, Type IV | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 34 %p. 1: Tensile Elongation | ASTM D638 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 0.45 MPa | 102 °Cp. 1: Heat Deflection Temperature | ASTM D648As the sheet prints it: 66 PSI ASTM D648 | not in the median: set apart (never used to pass), test bar not described as printed |
| MatterHackers, Black PRO Series Nylon Filament - 1.75mm (0.75kg) | MatterHackers1 value | |||
| Density | 1.14 g/cm3p. 1: Density | no standard stated | |
Print settings
- Nozzle
- 240–260 °Cown data sheet
- Bed
- 65 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 75 °C for 8 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 240°C - 260°C; Bed 65°C; Drying 75°C for 8 hoursMatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1: Recommended printing settings; p. 1: Suggested printing bed material
Price
Not in the price sample.
Its 3 documents
What the maker says (6)
- Benefits
PRO Series Nylon has excellent Impact Resistance as well as high Chemical Resistance
MatterHackers, Black PRO Series Nylon Filament - 1.75mm (0.75kg) | MatterHackersp. 1: exact-product Benefits paragraph - Moisture sensitivity
Suggested drying temperature 75°C for 8 hours
MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1 - Moisture sensitivity
Nylon materials inherently take up moisture from the surrounding atmosphere due to the nature of their chemistry.
MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1 - Moisture sensitivity
If moisture is present during extrusion, degradation can occur, resulting in a weaker part.
MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1 - Moisture sensitivity
A tell-tale sign of your nylon being too wet is popping noises and visible air bubbles escaping the extru- date.
MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1 - Moisture sensitivity
We recommend drying all nylons prior to printing.
MatterHackers, TECHNICAL DATA SHEET - PRO Series Nylonp. 1
eSUN ePAStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg39Nozzle, °C250–290Bed, °C70–90Chamber, °C—Drying, °C, h70≥ 12 h
eSUN ePAeSUN
Data sheet shared with eSUN PA Nylon Filament (1kg) Natural: their values are one table, recorded once.
Published values
No value is on file for this product.
Print settings
- Nozzle
- 250–290 °Cown data sheet
- Bed
- 70–90 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 70 °C for ≥ 12 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 250 - 290℃; Bed 70-90°C; Drying 70℃/> 12 heSUN, ePA Technical Data Sheetp. 2: Extruder Temperature, Build Platform Temperature
Price
39 CAD/kgits one regular price in the sample
1 listing
- DigitMakers: 39 CAD/kgESun ePA Natural - Nylon 1.75mm 1Kg (SKU ESUN-FL-EPA-NTRL-1.75-1KG)in its price; seen 30 Sep 2026
Its 2 documents
What the maker says (5)
- Good for
Machinery
eSUN, ePA Technical Data Sheetp. 1 - Good for
Self-lubricating wear resistance makes it suitable for printing gears
eSUN, ePA Technical Data Sheetp. 1 - Benefits
Self-lubricating wear-resisting
eSUN, ePA Technical Data Sheetp. 1 - Warping and shrinkage
Low shrinkage, not easy to warp and crack when printing.
eSUN, ePA Technical Data Sheetp. 1 - Moisture sensitivity
Drying (70℃/> 12 h) before printing to achieve the best printing effect, it is recommended to use with eBOX when printing.
eSUN, ePA Technical Data Sheetp. 2
eSUN PA Nylon Filament (1kg) NaturalStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg40Nozzle, °C250–290Bed, °C70–90Chamber, °C—Drying, °C, h70≥ 12 h
eSUN PA Nylon Filament (1kg) NaturaleSUN
Data sheet shared with eSUN ePA: their values are one table, recorded once.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| eSUN, PA Technical Data Sheet7 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile strength (yield or break not stated) orientation not stated | 52.45 MPap. 1: Tensile Strength GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Elongation at break orientation not stated | 175.32 %p. 1: Elongation at Break GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Flexural modulus orientation not stated | 1370 MPap. 1: Flexural Modulus GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Flexural strength orientation not stated | 58 MPap. 1: Flexural Strength GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Izod impact strength | 18.4 kJ/㎡p. 1: IZOD Impact Strength | GB/T 1843 | not in the median: measured on a moulded bar |
| HDT at 0.45 MPa | 50 ℃p. 1: Heat distortion Temperature GB/T 1634 | GB/T 1634As the sheet prints it: 0.45MPa GB/T 1634 | not in the median: measured on a moulded bar |
| Density | 1.12 g/cm3p. 1: Density GB/T 1033 | specimen not stated, GB/T 1033 | |
| eSUN, ePA Technical Data Sheet4 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile strength (yield or break not stated) | 52.45 MPap. 1: Tensile Strength | GB/T 1040 | not in the median: measured on a moulded bar |
| Elongation at break | 175.32 %p. 1: Elongation at Break | GB/T 1040 | not in the median: measured on a moulded bar |
| Flexural modulus | 1370 MPap. 1: Flexural Modulus | GB/T 9341 | not in the median: measured on a moulded bar |
| Flexural strength | 58 MPap. 1: Flexural Strength | GB/T 9341 | not in the median: measured on a moulded bar |
Print settings
- Nozzle
- 250–290 °Cown data sheet
- Bed
- 70–90 °Cown data sheet
- Heated chamber
- not stated
- Drying
- 70 °C for ≥ 12 hown data sheet
- Hardened nozzle
- not stated
Its print profile, in the documents' words
- Nozzle 250 - 290℃; Bed 70-90°C; Drying Drying (70℃/> 12 h) before printingeSUN, PA Technical Data Sheetp. 2: Recommended printing settings; p. 2: Drying note
Price
40 CAD/kgits one regular price in the sample
1 listing
- Shop3D.ca: 40 CAD/kgeSun PA Nylon Filament (1kg) Natural / 1.75mm (SKU PA175T1TZ1)in its price; seen 30 Sep 2026
Its 3 documents
What the maker says (7)
- Good for
Machinery
eSUN, PA Technical Data Sheetp. 1 - Good for
Self-lubricating wear resistance makes it suitable for printing gears
eSUN, PA Technical Data Sheetp. 1 - Benefits
Excellent printability
eSUN, PA Technical Data Sheetp. 1 - Benefits
Self-lubricating wear-resisting
eSUN, PA Technical Data Sheetp. 1 - Benefits
High toughness and impact resistance, with an elongation at break of up to 175%, which can print strong and durable parts with high fracture resistance
eSUN, PA Technical Data Sheetp. 1 - Warping and shrinkage
Low shrinkage, not easy to warp and crack when printing.
eSUN, PA Technical Data Sheetp. 1 - Moisture sensitivity
Drying (70℃/> 12 h) before printing to achieve the best printing effect, it is recommended to use with eBOX when printing.
eSUN, PA Technical Data Sheetp. 2
No product matches "".
Values are for the colour each sheet tested; pigment can change them.