ABS-GF
11 products from 11 makers. Most documented first. Select a column to sort, a product to see its values, print settings and documents.
11 products
Key
- set apart: test bar not described as printed, or no stated load
- measured after annealing
- from the Bambu Lab Filament Guide
- Izod where no Charpy is published
- sold as toughened
- hardened nozzle
- not published
How the numbers are worked out
Bambu Lab ABS-GFStrength XY, MPa36Strength Z, MPa29Modulus XY, GPa3.16Charpy notched, kJ/m²4.2HDT 0.45, °C99HDT 1.8, °C88Price, CAD/kg39Nozzle, °C240–280Bed, °C80–100Chamber, °C45–60Drying, °C, h808 h
Bambu Lab ABS-GFBambu Lab
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GF20 valuesUnless a row says otherwise: printed specimendryDried before testing (see preparation)annealed at 80 °C for 12 hAll the specimens were annealed and dried at 80 °C for 12 h before testingprint settingsSpecimen Printing Conditions Subjects Data Nozzle Temperature 270 °C Bed Temperature 80 °C Printing Speed 150 mm/s InfillDensity 100% * All the specimens were annealed and dried at 80 °C for 12 h before testing. And the suggested annealing temperature ofmodels printed with Bambu ABS-GF is80 to90 °C, and the time is6 to 12 hours. The annealing effect depends on the annealing t | |||
| Tensile modulus XY | 3160 ±170 MPap. 2: Young's Modulus (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile modulus Z | 2250 ± 130 MPAp. 2: Young's Modulus (Z) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) XY | 36 ±3 MPap. 2: Tensile Strength (X-Y) | ISO 527, GB/T 1040 | in the median |
| Tensile strength (yield or break not stated) Z | 29 ±3 MPap. 2: Tensile Strength (Z) | ISO 527, GB/T 1040 | in the median |
| Elongation at break XY | 1.2 %p. 2: Breaking Elongation Rate (X-Y) | ISO 527, GB/T 1040As the sheet prints it: ISO 527, GB/T 1040 6.3% ± | in the median |
| Elongation at break Z | 0.8 %p. 2: Breaking Elongation Rate (Z) | ISO 527, GB/T 1040As the sheet prints it: ISO 527, GB/T 1040 2.3% ± | in the median |
| Flexural modulus XY | 2860 ±130 MPap. 2: Bending Modulus (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural modulus Z | 1970 ±110 MPap. 2: Bending Modulus (Z) | ISO 178, GB/T 9341 | in the median |
| Flexural strength XY | 68 ±4 MPap. 2: Bending Strength (X-Y) | ISO 178, GB/T 9341 | in the median |
| Flexural strength Z | 46 ±3 MPap. 2: Bending Strength (Z) | ISO 178, GB/T 9341 | in the median |
| Charpy impact strength XY | 14.5 ± 1.5 kJ/m²p. 2: Impact Strength (X-Y) | ISO 179, GB/T 1043unnotched | not in the median: unnotched |
| Charpy impact strength XY | 4.2 ± 1.1 kJ/m² (notched)p. 2: Impact Strength (X-Y) (notched) | ISO 179, GB/T 1043 | in the median |
| Charpy impact strength Z | 5.3 ± 1.4 kJ/m²p. 2: Impact Strength (Z) | ISO 179, GB/T 1043 | not in the median: notch not stated |
| HDT at 0.45 MPa | 99 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 0.45 MPa | in the median |
| HDT at 1.8 MPa | 88 °Cp. 2: Heat Deflection Temperature | ISO 75As the sheet prints it: ISO 75 1.8 MPa | in the median |
| Vicat softening temperature | 103 °Cp. 2: Vicar Softening Temperature | ISO 306, GB/T 1633 | |
| Melting temperature | 202 °Cp. 2: Melting Temperature | DSCAs the sheet prints it: DSC, 10 °C/min | |
| Density | 1.08 g/cm³p. 2: Density | specimen not stated, ISO 1183 | |
| Water absorption | 0.53 %p. 2: Saturated Water | no standard namedAs the sheet prints it: ter Absorption Rate 25 °C, 55% RH | |
| Melt mass-flow rate | 7.56 ± 1.4 g/10 minp. 2: Melt Index | specimen not stated, no standard namedAs the sheet prints it: 210 °C, 2.16 kg | |
| Also named without a value: glass transition temperature, crystallization temperature. | |||
| Bambu Lab, Bambu Lab ABS-GF safety data sheet1 value | |||
| Fibre content | 10-20 %p. 4: Glass fibre | no standard stated | |
Print settings
- Nozzle
- 240–280 °Cown data sheet
- Bed
- 80–100 °Cown data sheet
- Heated chamber
- 45–60 °Cown data sheet
- Drying
- 80 °C for 8 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
- Annealing
- 80 °C for 12 hown data sheet
Its 2 print profiles, in the documents' words
- Nozzle 240 - 280 °C; Bed 80 -100 °C; Chamber 45 - 60 °C; Drying Blast Drying Oven: 80 °C, 8 hBambu Lab, Bambu Filament Technical Data Sheet - ABS-GFRecommended printing settings
- Drying Dry Out Before UseBambu Lab, ABS-GF official maker product pagep. 1: Cautions for Use
Price
39 CAD/kgits one regular price in the sample
1 listing
- Bambu Lab Canada: 39 CAD/kgABS-GF - White (41100) / Filament with spool / 1 kgin its price; seen 10 Sep 2026
Its 4 documents
What the maker says (6)
- Good for
ABS-GF is ideal for both mechanical parts and decorations due to the inherited water resistance, wear resistance, durability and vibrant colors.
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFp. 1 - Warping and shrinkage
Compared with regular ABS, ABS-GF outperforms in strength, stiffness, temperature resistance and dimensional stability, while being less prone to deformation and warping.
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFp. 1 - Surface finish
Glass fiber imparts a smooth matte finish with micro-spot gloss, blurring layer line.
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFp. 1 - Odour and emissions
Odor Odorless
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFp. 3 - Good for
ABS-GF outclasses regular ABS in strength and stiffness, making it perfect for load-bearing and bending-resistance parts.
Bambu Lab, ABS-GF official maker product pagep. 1: exact product features/description/application tips, source text line 124 - Warping and shrinkage
To minimize warping, avoid printing large-sized high infill density models. Use enclosed printers and ensure the build plate is properly applied with glue for better print adhesion before printing. Set lower printing speed and higher heatbed temperature. For more details please refer to: Common print quality problems and solutions on WIKI .
Bambu Lab, ABS-GF official maker product pagep. 1: exact product features/description/application tips, source text line 162
Specimen preparation (1)
All the specimens were annealed and dried at 80 °C for 12 h before testing
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFTest specimen preparation
Chemicals and environment (7)
- Flammability: flammable
Flammable
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFFlammability - Water solubility: insoluble
Insoluble in water
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFSolubility - Acid resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFResistance to Acid - Alkali resistance: resistant
Resistant
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFResistance to Alkali - Organic solvent resistance: limited
Not resistant to some organic solvents
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFResistance to Organic Solvent - Oil and grease resistance: limited
Not resistant to some kinds of oil and grease
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFResistance to Oil and Grease - Post-processing: described in words
the suggested annealing temperature of models printed with Bambu ABS-GF is 80 to 90 °C, and the time is 6 to 12 hours.
Bambu Lab, Bambu Filament Technical Data Sheet - ABS-GFp. 3: Annealing note
QIDI NexABS-GF25Strength XY, MPa48.5Strength Z, MPa30.5Modulus XY, GPa3.75Charpy notched, kJ/m²8.91HDT 0.45, °C87HDT 1.8, °C81Price, CAD/kg—Nozzle, °C250–270Bed, °C100–110Chamber, °CenclosedDrying, °C, h704–6 h
QIDI NexABS-GF25QIDI
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| QIDI, Technical Data Sheet QIDI NexABS-GF2515 valuesUnless a row says otherwise: printed specimen | |||
| Tensile modulus XY | 3752.13 ± 68.39 MPap. 4: 杨氏模量(X-Y) Young's Modulus | no standard stated | in the median |
| Tensile modulus Z | 2843.56 ± 69.90 MPap. 4: 杨氏模量(Z) ISO 527 Young's Modulus | ISO 527 | in the median |
| Tensile break strength XY | 48.48 ± 0.61 MPap. 4: 拉伸断裂强度(X-Y) Tensile breaking strength | no standard stated | in the median |
| Tensile break strength Z | 30.48 ± 0.47 MPap. 4: 拉伸断裂强度(Z) Tensile breaking strength | no standard stated | in the median |
| Elongation at break XY | 2.10 ± 0.10 %p. 4: 断裂伸长率(X-Y) ISO 527 Elongation at break | ISO 527 | in the median |
| Elongation at break Z | 2.20 ± 0.44 %p. 4: 断裂伸长率(Z) Elongation at break | no standard stated | in the median |
| Flexural modulus XY | 3531.71 ± 75.79 MPap. 4: Bending Modulus | no standard stated | in the median |
| Flexural strength XY | 78.80 ± 1.26 MPap. 4: 弯曲强度(X-Y) Bending strength | no standard stated | in the median |
| Charpy impact strength XY | 8.91 ± 0.63 KJ/㎡p. 4: 缺口冲击强度(X-Y) ISO 179 Charpy impact strength | ISO 179notched | in the median |
| HDT at 0.45 MPa | 87 °Cp. 3: Heat deflection temperature | no standard namedAs the sheet prints it: 0.45MPa | in the median |
| HDT at 1.8 MPa | 81 °Cp. 3: 热变形温度 ISO 75:Method A | ISO 75As the sheet prints it: 1.8MPa ISO 75 | in the median |
| Glass transition temperature | 103 °Cp. 3: 玻璃化转变温度 ISO 11357 Glass transition temperature | specimen not stated, ISO 11357 | in the median |
| Density | 1.15 g/cm³p. 3: 密度 ISO 1183 Density | specimen not stated, ISO 1183 | |
| Melt mass-flow rate | 4.2 g/10minp. 3: Glass transition temperature 熔融指数 250°C,2.16kg Melt index | specimen not stated, no standard namedAs the sheet prints it: 250°C,2.16kg | |
| Fibre content | 25% chopped glass fiberp. 2: Fibre content | specimen not stated, no standard stated | |
| QIDI, QIDI Filament Guide | Choose the Right Filament2 values | |||
| Tensile strength (yield or break not stated) Z | 30.48MPap. 1: Tensile Strength - Z | no standard stated | not in the median: replaced by a newer edition of the sheet or by the data sheet, so not used in deciding |
| Water absorption | 0.38%p. 1: Saturated Water Absorption Rate | no standard statedafter moisture conditioningsaturation | |
Print settings
- Nozzle
- 250–270 °Cown data sheet
- Bed
- 100–110 °Cown data sheet
- Heated chamber
- enclosure needed, no temperatureBambu Lab Filament Guide
- Drying
- optional: 70 °C for 4–6 hown data sheet
- Hardened nozzle
- neededown data sheet
Differs in another document of this product, not used in deciding (a data sheet speaks before a product page, a newer edition before an older one): bed in QIDI, QIDI Filament Guide | Choose the Right Filament; drying in QIDI, QIDI Filament Guide | Choose the Right Filament.
Its 2 print profiles, in the documents' words
- Nozzle 250-270°C; Bed 100-110°C; Drying If the filament has been opened for a long time and problems such as air bubbles and stringing appear during the printing process, please dry the filament at 70°C for 4-6 hours.QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6: Drying note; p. 5: Nozzle temperature; p. 5: Build plate temperature; p. 6: Nozzle note
- Nozzle 250-270°C; Bed Textured PEI plate (90-110°C) / Smooth PEI plate with glue (90-110°C); Drying Required; Blast Drying Oven: 70-80°C / 4-6 hQIDI, QIDI Filament Guide | Choose the Right Filamentp. 1: Is drying highly recommended?; p. 1: Recommended hardware settings; p. 1: Bed Temperature & Type; p. 1: Extruder heat range
Price
Not in the price sample.
Its 3 documents
What the maker says (15)
- Benefits
The co-extrusion skin-core technology has greatly increased fiber content while maintaining the toughness of the filament and thus improved the mechanical properties as well as heat resistance of printed parts.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 1 - Nozzle wear
At the same time, the skin-core structured filament can also help to avoid contact between the reinforcing fibers of the filament and extruders or throats, which prolongs the service life of the entire extrusion parts of the 3D printer.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 2 - Nozzle wear
During the extrusion process, the QIDI can greatly reduce the wear of the nozzle.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 2 - Odour and emissions
Thanks to this advanced production process, the residual amount of solvents and monomers used in the production process in the final ABS product is so low that the filament has a low odor during printing.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 2 - Surface finish
Meanwhile, there is no floating fiber on the surface of the printed part, and the surface presents a bright matte texture.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 3 - Adhesion between layers
This skin-core structure not only contributes to the low shrinkage, warpage resistance and excellent mechanical properties which ordinary fiber-reinforced materials have, but stronger interlayer bonding performance for printed parts as well.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 3 - Adhesion between layers
It has fixed the defect that the ordinary fiber-reinforced material will lose the bonding strength between layers.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 3 - Supports and removal
QIDI S-White Quick-Remove Support Material
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 5 - Warping and shrinkage
This technology further improves the warping resistance and rigidity of ABS materials, so the chamber temperature can be properly reduced to achieve energy saving.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Surface finish
when the printing speed is too high, the melt flow state will become unstable, and the filaments extruded from the nozzle will no longer have the skin-core structure anymore, which can cause the rough surface of the printed part.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Moisture sensitivity
If the filament has been opened for a long time and problems such as air bubbles and stringing appear during the printing process, please dry the filament at 70°C for 4-6 hours.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Nozzle wear
It is recommended to use hardened steel nozzles or nozzles with greater abrasion resistance, which can effectively improve the printing quality.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Odour and emissions
It is recommended to place the printer in a well-ventilated environment when printing with ABS material.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Printing advice
When this phenomenon occurs, it is recommended to increase the printing temperature or reduce the extrusion speed.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6 - Printing advice
The thickness of the heating block is recommended to be no less than 12mm.
QIDI, Technical Data Sheet QIDI NexABS-GF25p. 6
Eryone Glass Fiber ABSStrength XY, MPa37.2Strength Z, MPa19.2Modulus XY, GPa1.74Charpy notched, kJ/m²—HDT 0.45, °C82HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–280Bed, °C80–100Chamber, °CnoneDrying, °C, h75–856 h
Eryone Glass Fiber ABSEryone
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Eryone, Technical Data Sheet (TDS) Glass Fiber ABS14 values | |||
| Tensile modulus XY | 1735.8 MPap. 2: Elastic modulus X-Y MPa | no standard statedprint settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile modulus Z (X-Z) | 1651.2 MPap. 2: Elastic modulus X-Z MPa | no standard statedprint settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile strength (yield or break not stated) XY | 37.2 MPap. 2: Tensile strength X-Y 50mm/min GB/T 1040.4 MPa | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Tensile strength (yield or break not stated) Z (X-Z) | 19.2 ± 4 MPap. 2: Tensile strength X-Z 50mm/min GB/T 1843 MPa | GB/T 1843As the sheet prints it: 50mm/min GB/T 1843print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Elongation at break XY | 2.0 %p. 2: Elongation at break X-Y 50mm/min GB/T 1040.4 % | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Elongation at break Z (X-Z) | 1.6 %p. 2: Elongation at break X-Z 50mm/min GB/T 1040.4 % | GB/T 1040As the sheet prints it: 50mm/min GB/T 1040.4print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Flexural modulus orientation not stated | 2487.4 MPap. 2: Bending modulus 2mm/min GB/T 9341 MPa | GB/T 9341As the sheet prints it: 2mm/min GB/T 9341print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Flexural strength orientation not stated | 57.9 MPap. 2: Bending strength 2mm/min GB/T 9341 MPa | GB/T 9341As the sheet prints it: 2mm/min GB/T 9341print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | in the median |
| Impact strength, test unclear | 6.2 kJ/m2p. 2: Charpy Impact strenght 2.75J GB/T 1843 kJ/m2 | GB/T 1843As the sheet prints it: 2.75J GB/T 1843print settingsprinting temperature=270 ° C, printing speed=150mm/s, base plate 90° C, filling=100%, nozzle diameter=0.4mm | listed under other properties |
| HDT at 0.45 MPa | 82 ℃p. 1: Heat distortion temperature(° C) ASTM D648 0.45MPa ℃ | ASTM D648As the sheet prints it: 0.45MPa ASTM D648 | not in the median: set apart (never used to pass), test bar not described as printed |
| Glass transition temperature | 104 ℃p. 1: Glass transition temperature (° C) DSC, 10 ° C/min ℃ | DSCAs the sheet prints it: ° C DSC | in the median |
| Density | 1.1 g/cm³p. 1: Density(g/cm³ at 21.5 ° C) ASTM D792 (ISO 1183, GB/T 1033) g/cm³ | ASTM D792, ISO 1183, GB/T 1033As the sheet prints it: g/cm³ at 21.5 ° C) ASTM D792 ISO 1183 GB/T 1033 | |
| Melt mass-flow rate | 30 g/10minp. 1: Melt Index(g/10 min) 220 ° C, 10kg 240 ° C, 2.16 kg g/10min | no standard namedAs the sheet prints it: g/10 min 220 ° C 10kg 240 ° C 2.16 kg | |
| Fibre content | 10%p. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 240–280 °Cown data sheet
- Bed
- 80–100 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 75–85 °C for 6 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 240-280 ℃; Bed 80-100℃; Drying 75-85℃, 6hEryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1: Recommended printing settings; p. 1: Sealed printing
Price
Not in the price sample.
Its 2 documents
What the maker says (5)
- Good for
It offers excellent mechanical properties, thermal stability, and printing efficiency, making it suitable for 3D printing applications that require certain levels of strength, rigidity, and heat resistance, such as tooling fixtures, manufacturing jigs, enclosures, and structural components.
Eryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1 - Benefits
Eryone Glass Fiber ABS is a glass fiber reinforced ABS material that supports printing in open environments.
Eryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1 - Warping and shrinkage
It features a balanced combination of strength, rigidity, and warping resistance
Eryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1 - Surface finish
has a matte, fine sand-smooth surface texture.
Eryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1 - Printing advice
Sealed printing Sealing print quality is better, supporting open printing
Eryone, Technical Data Sheet (TDS) Glass Fiber ABSp. 1
Siraya Tech Fibreheart ABS-GFStrength XY, MPa46.5Strength Z, MPa—Modulus XY, GPa2.35Charpy notched, kJ/m²—HDT 0.45, °C97HDT 1.8, °C93Price, CAD/kg—Nozzle, °C250–270Bed, °C100–110Chamber, °C50Drying, °C, h654–6 h
Siraya Tech Fibreheart ABS-GFSiraya Tech
Sold as toughened or impact-modified: "Superior Toughness: Glass Fiber enhances durability and impact resistance." (Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GF, p. 1). The maker's statement, not a test result.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GF13 values | |||
| Tensile modulus orientation not stated | 2350 MPap. 2: Mechanical Properties, Young’s Modulus | ASTM D638 | in the median |
| Tensile break strength XY | 46.5 MPap. 2: Mechanical Properties, Tensile Stress at Break | ISO 527 | in the median |
| Elongation at break XY | 3 %p. 2: Mechanical Properties, Elongation at Break | ASTM D638 | in the median |
| Flexural modulus orientation not stated | 2705 MPap. 2: Mechanical Properties, Bending Modulus | no standard stated | in the median |
| Flexural strength orientation not stated | 66.4 MPap. 2: Mechanical Properties, Bending Strength | no standard stated | in the median |
| Charpy impact strength orientation not stated | 8.5 kJ/m²p. 2: Mechanical Properties, Charpy impact strength | no standard stated | not in the median: notch not stated |
| Hardness | 82 Shore Dp. 2: Other Properties, Shore Hardness (D) | no standard stated | in the median |
| HDT at 0.45 MPa | 97 °Cp. 2: Other Properties, HDT, Method B | no standard namedAs the sheet prints it: Method B | in the median |
| HDT at 1.8 MPa | 93 °Cp. 2: Other Properties, HDT, Method A | no standard namedAs the sheet prints it: Method A | in the median |
| Glass transition temperature | 101 °Cp. 2: Other Properties, Glass Transition Temperature | no standard stated | in the median |
| Vicat softening temperature | 106 °Cp. 2: Other Properties, Vicat softening temperature | ISO 306 | |
| Melting temperature | 225 °Cp. 2: Other Properties, Melting Point | no standard stated | |
| Density | 1.08 g/cm³p. 2: Filament Properties, Filament Density | ISO 1183 | |
| Siraya Tech, Material Safety Data Sheet: Siraya Tech ABS-GF1 value | |||
| Fibre content | 18-22 %p. 2: Glass Fiber | no standard stated | |
Print settings
- Nozzle
- 250–270 °Cown data sheet
- Bed
- 100–110 °Cown data sheet
- Heated chamber
- 50 °Cown data sheet
- Drying
- optional: 65 °C for 4–6 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 250°C to 270°C; Bed 100°C to 110°C; Chamber 50°C; Drying If moisture absorption is suspected, dry the filament at 65°C for 4-6 hoursSiraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 4: Drying note; p. 3: Nozzle note; p. 3: (3) Enclosure
Price
Not in the price sample.
Its 3 documents
What the maker says (12)
- Good for
Automotive Industry: Interior and exterior trim parts, engine covers, dashboards, etc. Consumer Electronics: Casings for electronic products, etc. Sports Equipment: Used in manufacturing various sports equipment, such as bicycle parts, etc. Industrial Applications: Gears, valve components, various brackets, and mechanical parts, etc.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 1 - Benefits
Superior Toughness: Glass Fiber enhances durability and impact resistance.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 1 - Benefits
Stability: Maintains integrity under high temperatures and chemicals.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 1 - Warping and shrinkage
Precision Printing: Glass fiber increases rigidity, brings dimensional stability, and reduces warpage.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 1 - Warping and shrinkage
An enclosure is crucial for maintaining consistent printing temperatures, ideally around 50°C, to significantly reduce issues like warping and failure rates, particularly in cold climates.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 3 - Nozzle wear
For printing Fibreheart ABS-GF, use a hardened steel or diamond-tipped nozzle to withstand the abrasive nature of glass fiber.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 3 - Printing advice
Start with short and slow retraction first.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 3 - Printing advice
While nozzles larger than 0.2mm work, a 0.4mm nozzle often yields the best results, ensuring long-term printing consistency and quality.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 3 - Moisture sensitivity
Using a dry box with desiccant, maintaining humidity below 15% is ideal for prolonged storage.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 4 - Moisture sensitivity
ABS filaments, including Fibreheart ABS-GF, are prone to moisture absorption, which can adversely affect print quality.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 4 - Printing advice
Adjust retraction settings and print speed to tackle stringing.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 4 - Printing advice
Improve bed adhesion using a glue stick or hairspray, or by slightly increasing the bed temperature.
Siraya Tech, Technical Data Sheet: Siraya Tech Fibreheart ABS-GFp. 4
Chemicals and environment (3)
- Safety: described in words
Handle in accordance with good industrial hygiene and safety practice. Do not eat, drink or smoke at the workplace. Avoid dust formation by cutting or grinding. During printing, ensure good ventilation and local exhaust.
Processing ventilationSiraya Tech, Material Safety Data Sheet: Siraya Tech ABS-GFp. 3: section 7.1, Precautions for safe handling - Moisture sensitivity: described in words
To ensure technical integrity of the product store in the original container/box and keep at temperatures below 50ºC and in a dry place. Protect from moisture, product may be hygroscopic.
Moisture handlingSiraya Tech, Material Safety Data Sheet: Siraya Tech ABS-GFp. 3: section 7.2, Conditions for safe storage - Disposal and circularity: described in words
Dispose of in accordance with local regulations.
Siraya Tech, Material Safety Data Sheet: Siraya Tech ABS-GFp. 4: section 13.1, Waste treatment methods
SUNLU ABS-GFStrength XY, MPa55Strength Z, MPa—Modulus XY, GPa2.08Charpy notched, kJ/m²6IzodHDT 0.45, °C100HDT 1.8, °C—Price, CAD/kg—Nozzle, °C260–280Bed, °C90–100Chamber, °CnoneDrying, °C, h80
SUNLU ABS-GFSUNLU
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| SUNLU, ABS-GF14 valuesThe same values also in SUNLU, TECHNICAL DATA SHEET ISO ABS-GF. | |||
| Tensile modulus XY | 2085 MPap. 1: Young’s Modulus(X-Y) ISO527/2 1mm/min MPa | ISO 527As the sheet prints it: 1mm/min ISO527/2 | in the median |
| Tensile strength (yield or break not stated) XY | 54 MPap. 1: Tensile Strength(X-Y) ISO527/2 50mm/min MPa | ISO 527As the sheet prints it: 50mm/min ISO527/2 | not in the median: another value of this product is in it |
| Elongation at break XY | 10 %p. 1: Elongation at break(X-Y) ISO527/2 50mm/min % | ISO 527As the sheet prints it: 50mm/min ISO527/2 | not in the median: another value of this product is in it |
| Flexural modulus XY | 3490 MPap. 1: Flexural Modulus(X-Y) ISO178 2mm/min MPa | ISO 178As the sheet prints it: 2mm/min ISO178 | not in the median: another value of this product is in it |
| Flexural strength XY | 90 MPap. 1: Flexural Strength(X-Y) ISO178 2mm/min MPa | ISO 178As the sheet prints it: 2mm/min ISO178 | not in the median: another value of this product is in it |
| Izod impact strength XY | 6.7 KJ/m2p. 1: IZOD Impact Notched(X-Y) ISO180 23℃ KJ/m2 | ISO 180As the sheet prints it: 23℃ ISO180 | not in the median: another value of this product is in it |
| Izod impact strength ZX | 4.9 KJ/m2p. 1: IZOD Impact Notched (Z-X) ISO180 23℃ KJ/m2 | ISO 180As the sheet prints it: Z-X 23℃ ISO180 | not in the median: measured on a bar in another orientation |
| HDT at 0.45 MPa | 104 ℃p. 1: Heat Deflection (HDT) ISO75 0.45MPa ℃ | ISO 75As the sheet prints it: 0.45MPa ISO75 | not in the median: another value of this product is in it |
| Vicat softening temperature | 95 ℃p. 1: Vicat Softening Temp. ISO306 5kg,50℃/h ℃also in SUNLU, TECHNICAL DATA SHEET ISO ABS-GF | ISO 306As the sheet prints it: 5kg ISO306 | |
| Melting temperature | 148 ℃p. 1: Melting Point ISO11357-3 10℃/min ℃also in SUNLU, TECHNICAL DATA SHEET ISO ABS-GF | ISO 11357As the sheet prints it: ISO11357-3 | |
| Decomposition temperature | 418 ℃p. 1: @5%Decomposition Temp. ISO11358 20℃/min ℃ | ISO 11358 | |
| Density | 1.016 g/cm3p. 1: Density ISO1183 23℃ g/cm3 | ISO 1183As the sheet prints it: 23℃ ISO1183 | |
| Melt mass-flow rate | 6 g/10minp. 1: Melt Flow Rate ISO1133 190℃/2.16kg g/10min | ISO 1133As the sheet prints it: 190℃/2.16kg ISO1133 | |
| Mould shrinkage orientation not stated | 0.5 %p. 1: Mold Shrinkage ISO294 23℃ % | ISO 294As the sheet prints it: 23℃ ISO294 | |
| SUNLU, TECHNICAL DATA SHEET ISO ABS-GF11 valuesThe same values also in SUNLU, ABS-GF.Unless a row says otherwise: printed specimen | |||
| Tensile strength (yield or break not stated) XY | 55 ± 5 MPap. 1: (X-Y) Tensile Strength ISO 527/2 50 mm/min MPa | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | in the median |
| Elongation at break XY | 10 ± 2 %p. 1: (X-Y) Elongation at break ISO 527/2 50 mm/min % | ISO 527As the sheet prints it: 50 mm/min ISO 527/2print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural modulus XY | 3300 ± 500 MPap. 1: (X-Y) Flexural Modulus ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | in the median |
| Flexural strength XY | 85 ± 5 MPap. 1: (X-Y) Flexural Strength ISO 178 2 mm/min MPa | ISO 178As the sheet prints it: 2 mm/min ISO 178print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength XY | 6 ± 2 KJ/m2p. 1: (X-Y) Izod Impact Strength of Notched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | in the median |
| Izod impact strength ZX | 5 ± 2 KJ/m2p. 1: (Z-X) Izod Impact Strength of Unnotched ISO 180 23℃ KJ/m2 Specimen | ISO 180As the sheet prints it: 23℃ KJ/m2 Specimen ISO 180print settingsPrinting speed 100-200 mm/s; Printing temperature 270 °C; Infill: 100%; 90° raster orientation | not in the median: unnotched |
| Hardness | 80 Shore Dp. 1: Shore Hardness ISO 868 23℃ HA/HDalso in SUNLU, ABS-GF | ISO 868As the sheet prints it: 23℃ HA/HD ISO 868 | in the median |
| HDT XY, at 0.45 MPa | 100 ± 5 ℃p. 1: (X-Y) Heat Distortion (HDT) ISO 75 0.45 MPa ℃ | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | in the median |
| Glass transition temperature | 135 ℃p. 1: Glass Transition (Tg) ISO 11357-2 10 ℃/min ℃also in SUNLU, ABS-GF | ISO 11357As the sheet prints it: ISO 11357-2 | in the median |
| Density | 1.016 ± 0.01 g/cm3p. 1: Density ISO 1183 23℃ g/cm3 | specimen not stated, ISO 1183As the sheet prints it: 23℃ ISO 1183 | |
| Melt mass-flow rate | 7 ± 2 g/10 minp. 1: Melt Mass-flow Rate ISO 1133 220℃/10 kg g/10 min | ISO 1133As the sheet prints it: 220℃/10 kg ISO 1133 | |
| SUNLU, SUNLU ABS-GF safety data sheet1 value | |||
| Fibre content | 10 %p. 2: Glass fiber | no standard stated | |
Print settings
- Nozzle
- 260–280 °Cown data sheet
- Bed
- 90–100 °Cown data sheet
- Heated chamber
- not requiredown data sheet
- Drying
- 80 °Cown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Its 2 print profiles, in the documents' words
- Nozzle 260-280; Bed 90-100℃; Chamber Room Temperature; Drying 80℃SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 2: Recommended printing settings; p. 2: Nozzle Temp. ℃
- Nozzle 260-280; Bed 90-100 °C; Chamber Normal; Drying 80℃SUNLU, ABS-GFp. 1: Recommended printing settings; p. 2: Nozzle Print Temp.
Price
Not in the price sample.
Its 4 documents
What the maker says (10)
- Good for
Engineering/functional parts, ornaments, toys, accessories, figurines.
SUNLU, ABS-GFp. 1 - Benefits
High heat deflection temperature, high strength
SUNLU, ABS-GFp. 1 - Warping and shrinkage
low warping
SUNLU, ABS-GFp. 1 - Surface finish
matte texture.
SUNLU, ABS-GFp. 1 - Adhesion between layers
excellent layer adhesion
SUNLU, ABS-GFp. 1 - Good for
Engineering/functional parts, decorative items, toys, accessories, and figurines.
SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 1 - Benefits
High heat resistance and strength
SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 1 - Precision and tolerance
fine detail reproduction
SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 1 - Surface finish
with a matte finish
SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 1 - Adhesion between layers
excellent interlayer adhesion
SUNLU, TECHNICAL DATA SHEET ISO ABS-GFp. 1
3DXTECH FibreX ABS+GF10 Glass Fiber ABSStrength XY, MPa68Strength Z, MPa—Modulus XY, GPa4.21Charpy notched, kJ/m²—HDT 0.45, °C98HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–280Bed, °C90–100Chamber, °CenclosedDrying, °C, h808 h
3DXTECH FibreX ABS+GF10 Glass Fiber ABS3DXTECH
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
3DXTECH, Technical Data Sheet: FibreX™ ABS+GF10 Glass Fiber ABS9 valuesUnless a row says otherwise: printed specimenprint settingsPrinted Specimen Conditions Printer: Open Source FDM/FFF Nozzle: 0.4mm Layer Height: 0.25mm Infill: 100%, +/- 45° Extrusion Temp: 245°C Bed Temp: 110°C Specimen Orientation: XY Flat | |||
| Tensile modulus XY | 4210 MPap. 1: Tensile Modulus ISO 527 MPa | ISO 527 | in the median |
| Tensile break strength XY | 68 MPap. 1: Tensile Strength, Break ISO 527 MPa | ISO 527 | in the median |
| Elongation at break XY | 2 %p. 1: Tensile Elongation, Break ISO 527 % | ISO 527 | in the median |
| Flexural modulus XY | 4420 MPap. 1: Flexural Modulus ISO 178 MPa | ISO 178 | in the median |
| Flexural strength XY | 70 MPap. 1: Flexural Strength ISO 178 MPa | ISO 178 | in the median |
| HDT at 0.45 MPa | 98 °Cp. 1: Deflection Temperature at 0.45 ISO 75 °C | ISO 75As the sheet prints it: ISO 75, 0.45 MPa (66psi) | in the median |
| Glass transition temperature | 105 °Cp. 1: Glass Transition Temperature DSC °C | DSCAs the sheet prints it: DSC Tg | in the median |
| Density | 1.15 g/ccp. 1: Density ISO 1183 g/cc | ISO 1183As the sheet prints it: 1183 g/cc ISO 1183 | |
| Fibre content | ABS+GF10 %p. 1: Fibre content | specimen not stated, no standard statedprint settings not stated | |
Print settings
- Nozzle
- 240–280 °CBambu Lab Filament Guide
- Bed
- 90–100 °CBambu Lab Filament Guide
- Heated chamber
- enclosure needed, no temperatureBambu Lab Filament Guide
- Drying
- optional: 80 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- No temperature stated3DXTECH, Technical Data Sheet: FibreX™ ABS+GF10 Glass Fiber ABSp. 1: Printed Specimen Conditions, which are not printing guidance
Price
Not in the price sample.
Its 2 documents
Fiberlogy ABS GFStrength XY, MPa50Strength Z, MPa—Modulus XY, GPa3.5Charpy notched, kJ/m²10HDT 0.45, °C90HDT 1.8, °C80Price, CAD/kg—Nozzle, °C270–295Bed, °C90Chamber, °CenclosedDrying, °C, h604 h
Fiberlogy ABS GFFiberlogy
Sold as toughened or impact-modified: "has been optimized for impact strength and dimensional accuracy" (Fiberlogy, ABS+GF Filament, p. 1). The maker's statement, not a test result.
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Fiberlogy, TECHNICAL DATA SHEET Fiberlogy ABS GF10 valuesUnless a row says otherwise: specimen not stated; its document points to a moulded or resin bar | |||
| Tensile modulus orientation not stated | 3500 MPap. 1: Tensile Modulus ISO 527 MPa | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile break strength orientation not stated | 50 MPap. 1: Tensile Strength @ Break ISO 527 MPa | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 3.5 %p. 1: Elongation @ Break ISO 527 % | ISO 527 | not in the median: set apart (never used to pass), test bar not described as printed |
| Flexural strength orientation not stated | 70 MPap. 1: Flexular Strength ISO 178 MPa | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength | 10 kJ/m2p. 1: Charpy Impact Strength (Notched) @ 23℃ ISO 179 kJ/m2 | ISO 179As the sheet prints it: 23℃ ISO 179 | not in the median: set apart (never used to pass), test bar not described as printed |
| Charpy impact strength | 30 kJ/m2p. 1: Charpy Impact Strength (Unnotched) @ 23℃ ISO 179 kJ/m2 | ISO 179As the sheet prints it: 23℃ ISO 179 | not in the median: unnotched |
| HDT at 0.45 MPa | 90 °Cp. 1: Heat Distortion Temperature @ 0.45 MPa ISO 75 °C | ISO 75As the sheet prints it: 0.45 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| HDT at 1.8 MPa | 80 °Cp. 1: Heat Distortion Temperature @ 1.8 MPa ISO 75 °C | ISO 75As the sheet prints it: 1.8 MPa ISO 75 | not in the median: set apart (never used to pass), test bar not described as printed |
| Vicat softening temperature | 95 °Cp. 1: Vicat Softening Temperature ISO 306 °C | specimen not stated, ISO 306 | |
| Density | 1.12 g/cm3p. 1: Specific Density ISO 1183 g/cm3 | specimen not stated, ISO 1183 | |
| Fiberlogy, ABS+GF Filament2 valuesUnless a row says otherwise: printed specimen (implied by the document); set apart, as the same figure on a better document of the product istested at 23°C | |||
| Charpy impact strength orientation not stated | 10 kJ/m²p. 1: Charpy impact strength (notched) @ 23°C | ISO 179 | not in the median: another value of this product is in it |
| Charpy impact strength orientation not stated | 30 kJ/m²p. 1: Charpy impact strength (unnotched) @ 23°C | ISO 179 | not in the median: unnotched |
| Fiberlogy, Fiberlogy ABS GF safety data sheet (Polish)1 value | |||
| Fibre content | 10 %p. 2: 3.2 Mieszaniny, Włókno szklane (Udział masowy [%]) | no standard stated | |
Print settings
- Nozzle
- 270–295 °Cown data sheet
- Bed
- 90 °Cown data sheet
- Heated chamber
- enclosure needed, no temperatureown data sheet
- Drying
- 60 °C for 4 hown data sheet
- Hardened nozzle
- neededBambu Lab Filament Guide
Differs in another document of this product, not used in deciding (a data sheet speaks before a product page, a newer edition before an older one): nozzle in Fiberlogy, ABS+GF Filament.
Its 2 print profiles, in the documents' words
- Nozzle 270°C - 295°C; Bed 90°CFiberlogy, TECHNICAL DATA SHEET Fiberlogy ABS GFp. 1: Recommended printing settings
- Nozzle 270–285°C; Bed 90°C; Drying 60°C / 4 hoursFiberlogy, ABS+GF Filamentp. 1: Printing temperature; p. 1: Bed temperature; p. 1: Bed material; p. 1: Drying conditions; p. 1: Enclosed chamber
Price
Not in the price sample.
Its 4 documents
What the maker says (2)
- Benefits
Prints feature excellent layer bonding, improved adhesion to the build plate, and reduced shrinkage compared to standard ABS.
Fiberlogy, ABS+GF Filamentp. 1 - Benefits
has been optimized for impact strength and dimensional accuracy
Fiberlogy, ABS+GF Filamentp. 1
Flashforge ABSGF10Strength XY, MPa35.5Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C88HDT 1.8, °C—Price, CAD/kg—Nozzle, °C220–260Bed, °C100–120Chamber, °C25–60Drying, °C, h80≥ 5 h
Flashforge ABSGF10Flashforge
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Flashforge, Technical Data Sheet ABSGF10 Filament14 values | |||
| Tensile strength (yield or break not stated) XY | 35.5-36.5 Mpap. 1: Tensile Strength (X-Y) ISO 527 Mpa | ISO 527print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | in the median |
| Elongation at break XY | 3-3.5 %p. 1: Elongation at Break (X-Y) ISO 527 % | ISO 527print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | in the median |
| Flexural modulus XY | 3360-3456 Mpap. 1: Bending Modulus (X-Y) ISO 178 Mpa | ISO 178print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | in the median |
| Flexural modulus XZ | 1805-2075 Mpap. 1: Bending Modulus (X-Z) ISO 178 Mpa | ISO 178print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | not in the median: measured on a bar in another orientation |
| Flexural strength XY | 81-83.5 Mpap. 1: Bending Strength (X-Y) ISO 178 Mpa | ISO 178print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | in the median |
| Flexural strength XZ | 45-48.6 Mpap. 1: Bending Strength (X-Z) ISO 178 Mpa | ISO 178print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | not in the median: measured on a bar in another orientation |
| Izod impact strength XY | 8.2~8.6 KJ/m²p. 1: Izod Impact Strength (X-Y) | ISO 180print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | not in the median: notch not stated |
| Izod impact strength XZ | 6~7.3 KJ/m²p. 1: Izod Impact Strength (X-Z) | ISO 180print settingsTest Equipment Flashforge Guider 3 Ultra; Nozzle Diameter 0.4mm; Nozzle Temperature 240 °C; Printing Speed 200mm/s; Infill Density 100%; Infill Pattern Concentric | not in the median: notch not stated |
| HDT at 0.45 MPa | 88 ℃p. 1: HDT@ 0.455 MPa (66 psi) ISO 75 ℃ | ISO 75As the sheet prints it: 0.455 MPa 66 psi ISO 75 | in the median |
| Continuous service temperature | 85 ℃p. 1: Continuous Service Temperature IEC 60216 ℃ | IEC 60216 | |
| Density | 1.08-1.09 g/cm³p. 1: Density ISO 1183 g/cm³ | ISO 1183 | |
| Water absorption | 1 %p. 1: Water Absorption (23℃/24h) ISO 62 % | ISO 62As the sheet prints it: 23℃/24h ISO 62 | |
| Melt mass-flow rate | 20-30 g/10minp. 1: Melt Flow Rate (MFR) (220℃/10Kg) ISO 1133 g/10min | ISO 1133As the sheet prints it: MFR 220℃/10Kg ISO 1133 | |
| Fibre content | 10% glass fiberp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 220–260 °Cown data sheet
- Bed
- 100–120 °Cown data sheet
- Heated chamber
- 25–60 °Cown data sheet
- Drying
- 80 °C for ≥ 5 hown data sheet
- Hardened nozzle
- neededown data sheet
Its print profile, in the documents' words
- Nozzle 220~260°C (240°C recommended); Bed 100~120°C (110°C recommended); Chamber Room temperature~60℃; Drying Using a hot dry air oven at 80°C for at least 5 hours is recommendedFlashforge, Technical Data Sheet ABSGF10 Filamentp. 2: Recommended printing settings: Nozzle Temperature; p. 2: Ambient Temperature for Printing; p. 3: Drying note; p. 2: Build Surface Material; p. 2: Nozzle & Gear Material; p. 2: Nozzle Diameter (recommended printing settings)
Price
Not in the price sample.
Its 2 documents
What the maker says (5)
- Benefits
Dimensional stability/High rigidity/Heat resistance.
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 1 - Nozzle wear
Nozzle & Gear Material Hardened steel
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 2 - Printing advice
Higher speeds require higher temperatures.
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 2 - Moisture sensitivity
As the ABSGF10 filament absorbs moisture easily due to the added glass fiber, it should be dried before being used.
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 3 - Printing advice
After the printing process, it is recommended to dry the model in the oven at 80°C for 1-3 hours to increase the strength of the model.
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 3
Chemicals and environment (1)
- Post-processing: described in words
After the printing process, it is recommended to dry the model in the oven at 80°C for 1-3 hours to increase the strength of the model.
Flashforge, Technical Data Sheet ABSGF10 Filamentp. 3: Post-processing note
Fabru Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)Strength XY, MPa81Strength Z, MPa—Modulus XY, GPa4.2Charpy notched, kJ/m²—HDT 0.45, °C100HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–260Bed, °C80–110Chamber, °CenclosedDrying, °C, h804 h
Fabru Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)Fabru
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| Fabru, Acrylnitrilbutadienstyrol Glasfaser 10% (ABS GF10)8 values | |||
| Tensile modulus orientation not stated | 4200 MPap. 1: Zug-E-Modul (ISO 178) | ISO 178 | not in the median: set apart (never used to pass), test bar not described as printed |
| Tensile yield strength orientation not stated | 81 MPap. 1: Streckspannung (ISO 527-1,2) | ISO 527As the sheet prints it: ISO 527-1,2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 3 %p. 1: Reissdehnung (ISO 527-1,2) | ISO 527As the sheet prints it: ISO 527-1,2 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at yield orientation not stated | 3 %p. 1: Streckdehnung (ASTM D638) | ASTM D638 | listed under other properties |
| Vicat softening temperature | 95 °Cp. 1: Vicat Erweichungstemperatur A | no standard stated | |
| Density | 1.11 g/cm3p. 1: Dichte (ISO 1183) | ISO 1183 | |
| Melt mass-flow rate | 24 g/10minp. 1: MFR (ISO 1133) | ISO 1133 | |
| Mould shrinkage orientation not stated | 0.2-0.4 %p. 1: Schwindung (ISO 294-4, 2577) | ISO 294As the sheet prints it: 2577 ISO 294-4 | |
| Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)2 values | |||
| HDT at 0.45 MPa | 100 °Cp. 1: Heat deflection temperature 0.45 MPa (ASTM D648) | ASTM D648As the sheet prints it: ASTM D648; 0.45 MPa | not in the median: set apart (never used to pass), test bar not described as printed |
| Fibre content | 10% glass fibersp. 1: Fibre content | no standard stated | |
Print settings
- Nozzle
- 240–260 °Cown data sheet
- Bed
- 80–110 °Cown data sheet
- Heated chamber
- enclosure needed, no temperatureown data sheet
- Drying
- 80 °C for 4 hown data sheet
- Hardened nozzle
- neededown data sheet
Its 3 print profiles, in the documents' words
- Nozzle 240-260 °C; Bed 80-110 °C; Drying 80°C; Drying time 2-4hFabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1: Nozzle note
- Nozzle 240-260 ° C; Bed 80-110 ° CFabru, purefil ABS GF10 tiefschwarz 1kg 1.75mmp. 1: Nozzle temperature; p. 1: Printing table temperature; p. 1: Description
- Nozzle 240-260 °C; Bed 80-110 °C; Drying 80°C; 2-4hFabru, Acrylnitrilbutadienstyrol Glasfaser 10% (ABS GF10)p. 1: Drucktemperatur; p. 1: Heizbett Temperatur; p. 1: Trocknungstemperatur / Trocknungsdauer
Price
Not in the price sample.
Its 4 documents
What the maker says (11)
- Pitfalls and limitations
The disadvantage of glass fiber reinforcement is the lower elongation at break.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Warping and shrinkage
Low shrinkage
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Warping and shrinkage
ABS GF10 has less shrinkage than unreinforced ABS and is therefore much easier to print because the material warps significantly less and therefore adheres better to the printing plate.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Warping and shrinkage
Shrinkage (ISO 294-4, 2577) 0.2-0.4 %
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Nozzle wear
Increased abrasion in the printing nozzle
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Nozzle wear
Hardened steel nozzle recommended
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Nozzle wear
We therefore recommend using a hardened steel nozzle to print large objects.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Odour and emissions
When ABS filament is melted, an odor develops.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Odour and emissions
Make sure your printer is in a well-ventilated room and avoid breathing in these fumes.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Odour and emissions
Make sure that no people who are sensitive to chemicals, children or pets stay in this room for a long time.
Fabru, Acrylnitrilbutadienstyrol glass fiber 10% (ABS GF10)p. 1 - Nozzle wear
We therefore recommend using a hardened steel nozzle to print large objects.
Fabru, purefil ABS GF10 tiefschwarz 1kg 1.75mmp. 1
iSANMATE ABS Glass FiberStrength XY, MPa51Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²27IzodHDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–280Bed, °C90–100Chamber, °CenclosedDrying, °C, h808 h
iSANMATE ABS Glass FiberiSANMATE
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| iSANMATE, ABS玻纤原料物性表5 valuesThe same values also in iSANMATE, ABS Glass Fiber Technical Data Sheet.Unless a row says otherwise: specimen not stated | |||
| Izod impact strength orientation not stated | 27 KJ/M2p. 1: 缺口冲击强度 | specimen not stated; its document points to a moulded or resin bar, ISO 180As the sheet prints it: ISO 180-A | not in the median: another value of this product is in it |
| Vicat softening temperature | 88 ℃p. 1: 维卡软化点 A/120also in iSANMATE, ABS Glass Fiber Technical Data Sheet | ASTM D648As the sheet prints it: ASTM D-648; method=A/120 | |
| Melting temperature | 180-200 ℃p. 1: 熔点also in iSANMATE, ABS Glass Fiber Technical Data Sheet | DSC | |
| Density | 1.10-1.13 g/cm3p. 1: 密度also in iSANMATE, ABS Glass Fiber Technical Data Sheet | ASTM D792 | |
| Water absorption | <1 %p. 1: 吸水率also in iSANMATE, ABS Glass Fiber Technical Data Sheet | ASTM D570 | |
| iSANMATE, ABS Glass Fiber Technical Data Sheet4 valuesThe same values also in iSANMATE, ABS玻纤原料物性表.Unless a row says otherwise: specimen not stated | |||
| Tensile strength (yield or break not stated) orientation not stated | 51 MPap. 1: Tensile Strengthalso in iSANMATE, ABS玻纤原料物性表 | ASTM D638 | not in the median: set apart (never used to pass), test bar not described as printed |
| Elongation at break orientation not stated | 12 %p. 1: Elongation at breakalso in iSANMATE, ABS玻纤原料物性表 | ASTM D638 | not in the median: set apart (never used to pass), test bar not described as printed |
| Izod impact strength | 27 KJ/M2p. 1: Notched impact strength | ISO 180As the sheet prints it: ISO 180-A | not in the median: set apart (never used to pass), test bar not described as printed |
| Melt mass-flow rate | 18-22 g/10minp. 1: Melt Flow Indexalso in iSANMATE, ABS玻纤原料物性表 | ASTM D1238As the sheet prints it: 220℃ 10Kg) ASTM D-1238 | |
Print settings
- Nozzle
- 240–280 °CBambu Lab Filament Guide
- Bed
- 90–100 °CBambu Lab Filament Guide
- Heated chamber
- enclosure needed, no temperatureBambu Lab Filament Guide
- Drying
- optional: 80 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
Price
Not in the price sample.
Its 2 documents
What the maker says (2)
- Warping and shrinkage
Low shrinkage and low shrinkage, which reduces the warpage of the printed model
iSANMATE, ABS Glass Fiber Technical Data Sheetp. 1 - Surface finish
Good matte texture
iSANMATE, ABS Glass Fiber Technical Data Sheetp. 1
eSUN eABS-GFStrength XY, MPa—Strength Z, MPa—Modulus XY, GPa—Charpy notched, kJ/m²—HDT 0.45, °C—HDT 1.8, °C—Price, CAD/kg—Nozzle, °C240–280Bed, °C90Chamber, °CenclosedDrying, °C, h808 h
eSUN eABS-GFeSUN
Published values
| Property | As published | Conditions | On the Overview |
|---|---|---|---|
| eSUN, eABS-GF Technical Data Sheet7 valuesUnless a row says otherwise: moulded bar (resin supplier's value) | |||
| Tensile strength (yield or break not stated) orientation not stated | 19.84 MPap. 1: Tensile Strength GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Elongation at break orientation not stated | 3.82 %p. 1: Elongation at Break GB/T 1040 | GB/T 1040 | not in the median: measured on a moulded bar |
| Flexural modulus orientation not stated | 2185.5 MPap. 1: Flexural Modulus GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Flexural strength orientation not stated | 60.08 MPap. 1: Flexural Strength GB/T 9341 | GB/T 9341 | not in the median: measured on a moulded bar |
| Izod impact strength | 4.42 kJ/m2p. 1: IZOD Impact Strength GB/T 1843 | GB/T 1843 | not in the median: measured on a moulded bar |
| HDT at 0.45 MPa | 97.65 ℃p. 1: Heat distortion Temperature | GB/T 1634As the sheet prints it: GB/T 1634 0.45Mpa | not in the median: measured on a moulded bar |
| Density | 1.07 g/cm3p. 1: Density GB/T 1033 | specimen not stated, GB/T 1033 | |
Print settings
- Nozzle
- 240–280 °Cown data sheet
- Bed
- 90 °Cown data sheet
- Heated chamber
- enclosure needed, no temperatureBambu Lab Filament Guide
- Drying
- optional: 80 °C for 8 hBambu Lab Filament Guide
- Hardened nozzle
- neededBambu Lab Filament Guide
Its print profile, in the documents' words
- Nozzle 240 - 280℃; Bed 90℃eSUN, eABS-GF Technical Data Sheetp. 2: Recommended printing settings: Extruder Temperature; p. 2: Based on Bambu P1S 0.4 mm nozzle
Price
Not in the price sample.
Its 2 documents
What the maker says (4)
- Good for
Aerospace • Automotive • Industrial applications
eSUN, eABS-GF Technical Data Sheetp. 1 - Benefits
High strength Wear resistance Impact resistance
eSUN, eABS-GF Technical Data Sheetp. 1 - Benefits
Chemical resistance
eSUN, eABS-GF Technical Data Sheetp. 1 - Benefits
Adding glass fiber reinforced materials to ABS and modifying,it strengthens the rigidity and toughness of ABS,it has excellent impact resistance and chemical corrosion resistance, and has good performance in scenes with high strength requirements such as some tooling and fixtures.
eSUN, eABS-GF Technical Data Sheetp. 1
No product matches "".
Values are for the colour each sheet tested; pigment can change them.